PIA0624SR10YN SUPERWORLD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 1. Part No. Expression: P I A 0 6 2 4 S 1 R 0 M N a) Series Code e) Tolerance Code (a) (b) (c) (d) (e)(f) b) Dimension Code f) Internal Controlled Code c) Type Code d) Inductance Code 2. Configuration & Dimensions: 3. Schematic: 4. Material List: a) Core b) Wire c) Terminal d) Ink A B C D E G H L L G H Recommended PC Board Pattern Note: 1. The above PCB layout is for reference only. 2. Solder paste thickness of 0.15mm and above is recommended. 3. Marking: Top row – Inductance code, Bottom row – YYWW Marking D/C Unit: mm
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 5. General Specification: (a) Operating Temp. : -40°C to +125°C (Inclusive of coil temp rise) (b) Storage Temp. : -40°C to +125°C (on board) (c) Humidity Range : 85 ± 2% RH (d) Heat Rated Current (Irms) will cause the coil temperature rise approximately ∆t of 40°C (keep 1min) (e) Saturation Current (Isat Typ.) will cause L0 to drop approximately 30%. (f) Part Temp. (Ambient + Temp. Rise) should not exceed 125°C under worst case operating conditions. (g) Storage condition (component in its packaging) i) Temperature: Less than 40°C ii) Humidity : 60% RH
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 6. Electrical Characteristics: Part Number Inductance Lo (uH) @ 0A Test Frequency, L Heat Rating Current DC ( A ) Irms. Saturation Current DC (A) Isat. DCR (mΩ)Typ. DCR (mΩ)Max. Typ. Max. Typ. Max. PIA0624SR10YN 0.10 100kHz/1.0V 30 25 70 60 1.2 1.35 PIA0624SR15MN 0.15 100kHz/1.0V 32 30 41 34 1.5 1.80 PIA0624SR22MN 0.22 100kHz/1.0V 26 23 34 28 2.2 2.53 PIA0624SR33MN 0.33 100kHz/1.0V 24 21 27 24 3.2 3.52 PIA0624SR36MN 0.36 100kHz/1.0V 23 20 25 22 3.4 3.80 PIA0624SR45MN 0.45 100kHz/1.0V 20 17 22 18 4.0 4.40 PIA0624SR47MN 0.47 100kHz/1.0V 19 16 22 18 4.4 5.06 PIA0624SR68MN 0.68 100kHz/1.0V 17 14 17 15 5.2 6.00 PIA0624SR82MN 0.82 100kHz/1.0V 16 13 16 14 7.3 8.10 PIA0624S1R0MN 1.00 100kHz/1.0V 13 11 15 13 10.0 11.8 *Tolerance code : M = ±20%, Y= ±30% Notes: 1) At all times, the current supplied to the product should not exceed Isat Max. value.
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 7. Characteristics Curves: PIA0624SR10YN PIA0624SR15MN PIA0624SR22MN PIA0624SR33MN PIA0624SR36MN PIA0624SR45MN PIA0624SR47MN PIA0624SR68MN PIA0624SR82MN PIA0624S1R0MN PIA0624S1R5MN PIA0624S2R2MN
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 PIA0624S3R3MN PIA0624S4R7MN PIA0624S5R6MN PIA0624S6R8MN PIA0624S100MN
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 8. Soldering: Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all re-flow solderin g systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air. 8-1 Solder Re-flow: Recommended temperature profiles for re-flow soldering in Figure 1. 8 - 2 Soldering Iron (Figure 2): Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. N o t e : a) Preheat circuit and products to 150°C. b) 355°C tip temperature (Max.) c ) N e v e r c o n t a c t t h e c e r a m i c w i t h t h e i r o n t i p d) 1.0mm tip diameter (Max.) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f ) L i m i t s o l d e r i n g t i m e t o 4 ~ 5 s e c s .
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 9. Packaging Information: 9-1 Reel Dimension 9 - 2 T a p e D i m e n s i o n D P W F T 200mm or more Direction of tape 400mm or more Blank portions 4.0 Chip cavity Blank portions 9-3 Packaging Quantity Type A(mm) B(mm) C(mm) D(mm) PIA 0624 Chip / Reel 1500 Inner box 3000 Carton 12000 Series Size Bo(mm) Ao(mm) Ko(mm) P(mm) W(mm) F(mm) T(mm) D(mm)
Molded Choke Coil – PIA0624S Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 16/11/2017 9-4 Tearing Off Force Application Notice: 1. Storage Conditions: To maintain the solderabililty of terminal electrodes: a) Recommended products should be used within 12 months from the time of delivery. b) The packaging material should be kept where no chlorine or sulfur exists in the air. 2. Transportation: a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) Vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. Room Temp. (℃) Room Humidity (%) Room atm (hPa) Tearing Speed mm/min 5~35 45~85 860~1060 300 The force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions.