PIA053TR10YN SUPERWORLD | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
Molded Choke Coil – PIA053T Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 17/11/2017 1. Part No. Expression: P I A 0 5 3 T 1 R 0 M N a) Series Code d) Inductance Code (a) (b) (c) (d) (e)(f) b) Dimension Code e) Tolerance Code c) Type Code f) Internal Controlled Code 2. Configuration & Dimensions: B C E D 1R0 1526 T A 3. Schematic: 4. Material List: a) Core b) Wire c) Terminal d) Ink A A\` B C D E T L G H L G H Recommended PC Board Pattern Note: 1. The above PCB layout is for reference only. 2. Solder paste thickness of 0.12mm and above is recommended. 3. Marking: Top row – Inductance code, Bottom row – YYWW Marking D/C Unit: mm
Molded Choke Coil – PIA053T Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 17/11/2017 5. General Specification: (a) Operating Temp. : -40°C to +125°C (Inclusive of coil temp rise). (b) Storage Temp. : -40°C to +125°C (on board).. (c) Humidity Range. : 85 ± 2% RH. (d) Heat Rated Current (Irms) will cause the coil temperature rise approximately ∆t of 40°C. (e) Saturation Current (Isat) will cause L0 to drop approximately 30%. (f) Part Temp. (Ambient + Temp. Rise) should not exceed 125°C under worst case operating conditions. (g) Storage condition (component in its packaging) i) Temperature: Less than 40°C ii) Humidity : 60% RH 6. Electrical Characteristics: Part Number Inductance L (uH) @ 0A Test Frequency (Hz) Irms (A) Typ. Irms (A) Max. Isat (A) Typ. Isat (A) Max. DCR (mΩ) Typ. DCR (mΩ) Max. *Tolerance code: M = ±20%, Y= ±30%
Molded Choke Coil – PIA053T Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 17/11/2017 7. Characteristics Curves: 0 8 16 24 32 40 DC CURRENT(A) 0.03 0.06 0.09 0.12 0.15 INDUCTANCE (uH) TEMP. RISE(oC) 0 8 16 24 32 40 DC CURRENT(A) 0.036 0.072 0.108 0.144 0.18 INDUCTANCE (uH) TEMP. RISE(oC) 0 5 10 15 20 25 DC CURRENT(A) 0.07 0.14 0.21 0.28 0.35 INDUCTANCE (uH) TEMP. RISE(oC) 0 3.6 7.2 10.8 14.4 18 DC CURRENT(A) 0.11 0.22 0.33 0.44 0.55 INDUCTANCE (uH) TEMP. RISE(oC) 0 3.2 6.4 9.6 12.8 16 DC CURRENT(A) 0.15 0.3 0.45 0.6 0.75 INDUCTANCE (uH) TEMP. RISE(oC) 0369 1 2 1 5 DC CURRENT(A) 0.24 0.48 0.72 0.96 1.2 INDUCTANCE (uH) TEMP. RISE(oC) 0369 1 2 1 5 DC CURRENT(A) 0.36 0.72 1.08 1.44 1.8 INDUCTANCE (uH) TEMP. RISE(oC) 02468 1 0 DC CURRENT(A) 0.36 0.72 1.08 1.44 1.8 INDUCTANCE (uH) TEMP. RISE(oC) 0 1.6 3.2 4.8 6.4 8 DC CURRENT(A) 0.5 1.5 2.5 INDUCTANCE (uH) TEMP. RISE(oC) 0 1.6 3.2 4.8 6.4 8 DC CURRENT(A) 0.7 1.4 2.1 2.8 3.5 INDUCTANCE (uH) TEMP. RISE(oC) 0 1.4 2.8 4.2 5.6 7 DC CURRENT(A) INDUCTANCE (uH) TEMP. RISE(oC) 0 1.4 2.8 4.2 5.6 7 DC CURRENT(A) 1.6 3.2 4.8 6.4 INDUCTANCE (uH) TEMP. RISE(oC) PIA053TR10YN PIA053TR12YN PIA053TR22MN PIA053TR35MN PIA053TR47MN PIA053TR68MN PIA053T1R0MN PIA053T1R2MN PIA053T1R5MN PIA053T2R2MN PIA053T3R3MN PIA053T4R7MN
Molded Choke Coil – PIA053T Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 17/11/2017 8. Soldering: Mildly activated rosin fluxes are preferred. The minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. Our terminations are suitable for all re-flow solderin g systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air. 8-1 Solder Re-flow Recommended temperature profiles for re-flow soldering in Figure 1. 8 - 2 Soldering Iron (Figure 2) Products attachment with soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. N o t e : a) Preheat circuit and products to 150°C. b) 355°C tip temperature (Max.) c ) N e v e r c o n t a c t t h e c e r a m i c w i t h t h e i r o n t i p d) 1.0mm tip diameter (Max.) e) Use a 20 watt soldering iron with tip diameter of 1.0mm f ) L i m i t s o l d e r i n g t i m e t o 4 ~ 5 s e c s .
Molded Choke Coil – PIA053T Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 17/11/2017 9. Packaging Information: 9-1 Reel Dimension 9 - 2 T a p e D i m e n s i o n D P W F T 200mm or more Direction of tape 400mm or more Blank portions 4.0 Chip cavity Blank portions 9-3 Packaging Quantity Type A(mm) B(mm) C(mm) D(mm) PIA 053 Chip / Reel 1000 Inner box 2000 Carton 8000 Series Size Bo(mm) Ao(mm) Ko(mm) P(mm) W(mm) F(mm) T(mm) D(mm)
Molded Choke Coil – PIA053T Series NOTE: Specifications subject to change without notice. Please check our website for latest information. Proprietary and Confidential Document of Superworld 17/11/2017 9-4 Tearing Off Force Application Notice: 1. Storage Conditions: To maintain the solderabililty of terminal electrodes: a) Recommended products should be used within 12 months from the time of delivery. b) The packaging material should be kept where no chlorine or sulfur exists in the air. 2. Transportation: a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) Vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. The force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions. Room Temp. (℃) Room Humidity (%) Room atm (hPa) Tearing Speed mm/min 5~35 45~85 860~1060 300