PD110-10 TRUMPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● sales@trumpower.com ● www.TRUMPower.com

110 WATT DC TO DC CONVERTERS

DESCRIPTION

The PD110 series of DC/DC conv erters provide up to 110 watts of continuous output power. Available in three standard input range of 10-20 VDC, 18-36 VDC and 36-72 VDC, they are ideal for a variety of applicatio ns including telecoms, portable equipment and vehicle mounted instrumentation. All units are available in compact “open PCB” or “enclosed” mechanical formats.

FEATURES

‧ Low cost ‧ Small size, light weight ‧ 100 ﹪ burn-in ‧ Overvoltage protection ‧ Overcurrent protection ‧ Three wide input ranges: 10-20 VDC, 18-36 VDC and 36-72 VDC PD110 SERIES INPUT SPECIFICATIONS Input voltage ： 10 to 20 VDC （ PD110 “L” series ） 18 to 36 VDC （ PD110 “M” series ） 36 to 72 VDC （ PD110 “H” series ） Input current ： 15A （ rms ） for 12VDC 9.4A （ rms ） for 24VDC 4.7A （ rms ） for 48VDC ENVIRONMENTAL SPECIFICATIONS Operating temperature ： 0 ℃ to +70 ℃ Storage temperature ： -40 ℃ to +85 ℃ Relative humidity ： 5 ﹪ to 95 ﹪ non-condensing Derating ： Derate from 100 ﹪ at +50 ℃ linearly to 50 ﹪ at +70 ℃ OUTPUT SPECIFICATIONS Output voltage/current ： See rating chart Total output power ： 110 watts maximum Ripple and noise ： 1﹪peak to peak max. Overvoltage protection ： set at 112 - 132 ﹪of its nominal output voltage Overcurrent protection ： All outputs protected to short circuit conditions Temperature coefficient ： All outputs ±0.04 ﹪/℃ maximum Transient response ： Maximum excursion of 4 ﹪or better on all models, recovering to 1 ﹪of final value within 500us after a 25 ﹪step load change GENERAL SPECIFICATIONS Switching frequency ： 50KHz ±5KHz Efficiency ： 70 ﹪minimum at full load Line regulation ： ±0.5 ﹪maximum at full load Withstand voltage ： 1000VDC from input to output MTBF ： 400,000 hours minimum at full load at 25 ℃ambient, calculated per MIL-HDBK-217F

DC TO DC CONVERTERS PD110 SERIES OUTPUT VOLTAGE/CURRENT RATING CHART Maximum (3) Output #1 Output #2(1) Output #3 Output #4 Output PD110-10 5V 0A 22A 3% (N/A) (N/A) (N/A) 110W PD110-12 12V 0A 9.0A 2% (N/A) (N/A) (N/A) 110W PD110-13 15V 0A 7.5A 2% (N/A) (N/A) (N/A) 110W PD110-14 24V 0A 4.5A 2% (N/A) (N/A) (N/A) 110W PD110-16 30V 0A 3.6A 2% (N/A) (N/A) (N/A) 110W PD110-23 +5V 0.8A 10A 3% + 12V 0A 5A 9.0A 3% (N/A) (N/A) 110W PD110-31 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% (N/A) 110W PD110-32 +5V 0.8A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% (N/A) 110W PD110-40 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% -5V 0A 1A 4% 110W PD110-41 +5V 0.8A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% +24V 0A 1A 4% 110W PD110-42 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PD110-45-1 +5V 0.8A 10A 3% +12V 0A 5A 9.0A 3% -12V 0A 1A 4% +24V 0A 1.5A 10% 110W PD110-45-2 +5V 0.8A 10A 3% +24V 0A 3A 5.0A 3% -12V 0A 1A 4% +12V 0A 1A 4% 110W PD110-46 +5V 0.8A 10A 3% +15V 0A 4A 7.5A 3% -15V 0A 1A 4% -5V 0A 1A 4% 110W Notes: (1) Peak output current with 10% maximum duty cycle for less than 60 seconds. (2) PD110”M” & “H” series are suitable only for 110 watts ma ximum at 20 CFM forced air cooling or 80 watts maximum at convection cooling. PD110”L” series are suitable only for 90 watts maximum at 20 CFM forced air cooling or 70 watts maximum at convection cooling. (3) Suffix codes for input range, mechan ical format and connector are as follows. PD110-X1X2X3X4X5, “X1X2” is the model code from the above table, “X3” is the input range (L=10-20 VDC, M=18-36 VDC, H=36-72 VDC), “X4” is the mechanical format (A=open PCB, B=L-bracket, C=enclosed) and “X5” is the input and output connector code (Blank=Molex KK type, T=miniature terminal block), e.g. PD110-31MCT (18-36 VDC input range, enclosed format and miniature terminal blocks). MECHANICAL SPECIFICATIONS NOTES: 1. Dimensions shown in inch [mm] 2. Tolerance 0.02 [0.5] maximum 3. Molex KK type connectors: Input connector mates with Molex housing 09-50-3051 and Molex 2878 series crimp terminal. Output connector mates with Molex housing 09-50-3131 and Molex 2878 series crimp terminal. 4. Miniature terminal blocks: Input terminals allow wires up to 2mm (AWG #14). Output terminals allow wires up to 2mm2 (AWG #14). 5. Weight: 640grams (PCB format) 6. See the mechanical details of L-bracket and enclosed formats in page 7-2. PIN CHART 1 2 3 4 5 6 1,2,3 4,5 6,7 8,9 10 11 12 13 PD110-10 PD110-13 PD110-16 PD110-12 PD110-14 OUTPUT #1 RETURN RETURN OUTPUT PD110-23 OUTPUT COMMON RETURN COMMON RETURN OUTPUT PD110-31 PD110-32 OUTPUT COMMON RETURN COMMON RETURN OUTPUT #2 N.C. OUTPUT #3 KEY N.C. PD110-40 PD110-42 PD110-45-2 PD110-41 PD110-45-1 PD110-46 OUTPUT COMMON RETURN COMMON RETURN OUTPUT #2 N.C. OUTPUT #3 KEY OUTPUT Tumbler Technologies + TRUMPower 3350 Scott Blvd., Bldg. 13, Santa Clara, California 95054, USA Phone: 408-988-6616 ● sales@trumpower.com ● www.TRUMPower.com MINI. TERMINAL MOLEX CONNECTOR MODEL