PCQA24-5750-U8-P1D-L02MM

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 16

Technical content

Resolution Refer to output specification Sampling rate Up to 1 kHz, depending on the measurement range Linearity Ranges >500 mm: L10 = ±0.10 % f.s. L02 = ±0.02 % f.s. Ranges ≤500 mm: L10 = ±0.5 mm L02MM = ±0.2 mm Repeatability ±3 µm Housing material AlMgSi1 / Zn / V4A Protection class IP67 (optional IP67/IP69K; connector version: with mating connector only) Shock EN 60068-2-27:2010, 50 g 11 ms, 100 shocks Vibration EN 60068-2-6:2008, 20 g 10 Hz-2 kHz, 10 cycles Connection Connector M12, 8 pin / cable 2 m EMC, temperature Refer to output specification POSICHRON® position sensor in square profile

• Protection class up to IP67/IP69K
• Absolute position measurement
• Easy installation with mounting brackets
• Wear free position magnet
• Contactless
• Also available with guided position magnet
• Analog output Order code mounting set (see page 7) POSICHRON® PCQA24 Square Profile Housing with Analog Output 1 channel Order code PCQA24 Model name Measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request Output = 0 ... 10 V signal conditioner U1/H = U1 with Alarm_HOLD (see page 11) U2 = 0.5 ... 10 V signal conditioner U2/U; U2/H = U2 with Alarm_LOW; U2 with Alarm_HOLD (see page 11) U8/U; U8/H = U8 with Alarm_LOW; U8 with Alarm_HOLD (see page 11) I1 = 4 ... 20 mA signal conditioner (3 wire) I1/U; I1/H = I1 with Alarm_LOW; I1 with Alarm_HOLD (see page 11) Function and characteristics output P1A = Position Magnet 1, increasing P1D = Position Magnet 1, decreasing PMU = Start value, direction & end value adjustable by the customer Linearity L02 / L02MM / L10 (for definition see "Specifications" above) Connection M12 = Connector M12, 8 pin KAB2M = Cable, standard length 2 m, other lengths upon request DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

KAB-...M-M12/8F/G-LITZE PCMAG ... PCQA24 Order code mating connecting cable (see page 15) Order code position magnet/slider (see page 8) POSICHRON® PCQA24 Square Profile Housing with Analog Output 1. Order example: PCQA24 - 1000 - I1 - P1A - P2D - L10 - M12 Square profile, measurement range 1000 mm, 2 current outputs 4 ... 20 mA (I1) Output 1: Position magnet 1, increasing signal (P1A) Output 2: Position magnet 2, decreasing signal (P2D) 2. Order example: PCQA24 - 1000 - U1 - P1A - VZ1.0 - L10 - M12 Square profile, measurement range 1000 mm, 2 voltage outputs 0.5 ... 10 V (U2) Output 1: Position magnet 1, increasing signal (P1A) Order Code PCQA24 Model name Measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request Output = 0 ... 10 V signal conditioner U1/H = U1 with Alarm_HOLD (see page 11) U2 = 0.5 ... 10 V signal conditioner U2/U; U2/H = U2 with Alarm_LOW; U2 with Alarm_HOLD (see page 11) U8/U; U8/H = U8 with Alarm_LOW; U8 with Alarm_HOLD (see page 11) I1 = 4 ... 20 mA signal conditioner (3 wire) I1/U; I1/H = I1 with Alarm_LOW; I1 with Alarm_HOLD (see page 11) Function and characteristics output 1 P1A = Position magnet 1, increasing P1D = Position magnet 1, decreasing DA = Difference magnet 1/2, increasing (2 magnets required) DD = Difference magnet 1/2, decreasing (2 magnets required) Function and characteristics output 2 P2A = Position magnet 2, increasing P2D = Position magnet 2, decreasing DA = Difference magnet 1/2, increasing DD = Difference magnet 1/2, decreasing VZx.x = Velocity with direction detection (with 1 magnet only) VZx.x = Velocity in steps of 0.1 m/s Example: VZ1.5 towards start position towards end position Output U2: 0.5 V 5.25 V 10 V Output I1: 4 mA 12 mA 20 mA VAx.x = Velocity without direction detection (with 1 magnet only) VAx.x = Velocity in steps of 0.1 m/s Example: VA1.5 towards start position towards end position Output U2: 10 V 0.5 V 10 V Output I1: 20 mA 4 mA 20 mA Linearity L02 / L02MM / L10 (for definition see "Specifications" above) Connection M12 = Connector M12, 8 pin KAB2M = Cable, standard length 2 m, other lengths upon request 2 channel, configurable 2 magnets required DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

KAB-...M-M12/8F/G-LITZE PCQA-BFS1 PCMAG ... / / PCQA24 / / Specifications Output Synchronous serial interface (SSI) Resolution 5, 10, 20, 50, 100 µm Sampling rate Up to 1 kHz, depending on the measurement range Linearity Ranges >500 mm: L10 = ±0.10 % f.s. L02 = ±0.02 % f.s. Ranges ≤500 mm: L10 = ±0.5 mm L02MM = ±0.2 mm Repeatability ±3 µm Housing material AlMgSi1 / Zn / V4A Protection class IP67 (optional IP67/IP69K; connector version: with mating connector only) Shock EN 60068-2-27:2010, 50 g 11 ms, 100 shocks Vibration EN 60068-2-6:2008, 20 g 10 Hz-2 kHz, 10 cycles Connection 8 pin socket / cable 2 m EMC, temperature Refer to output specification POSICHRON® position sensor in square profile

• Protection class IP67/IP69K
• Absolute position measurement
• Easy installation with mounting brackets
• Wear free position magnet
• Contactless
• Also available with guided position magnet
• Synchronous serial interface (SSI) Order code position magnet/slider (see page 8) Order code mounting set (see page 7) Order example: PCQA24 - 2500 - 10 - SSI/G/24 - L10 - M12 Order code mating connecting cable (see page 15) POSICHRON® PCQA24 Square Profile Housing with SSI Output Order Code PCQA24 Model name Measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request Resolution (in µm) 5 / 10 / 20 / 50 / 100 Output SSI = Synchronous serial interface Code G / D = Gray / Dual Number of data bits Linearity L02 / L02MM / L10 (for definition see "Specifications" above) Connection M12 = Connector M12, 8 pin KAB2M = Cable, standard length 2 m, other lengths upon request DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

PCMAG ... PCQA-BFS1 KAB-...M-M12/5F/G-M12/5M/G - CAN PCQA24 POSICHRON® PCQA24 Square Profile Housing with CAN Output POSICHRON® position sensor in square profile

• Protection class IP67/IP69K
• Absolute position measurement
• Easy installation with mounting brackets
• Wear free position magnet
• Contactless
• Also available with guided position magnet
• CANopen bus or CAN SAE J1939 output Specifications Output CANopen bus; CAN SAE J1939 Resolution 50 µm Sampling rate Up to 1 kHz, depending on the measurement range Linearity Ranges >500 mm: L10 = ±0.10 % f.s. L02 = ±0.02 % f.s. Ranges ≤500 mm: L10 = ±0.5 mm L02MM = ±0.2 mm Repeatability ±3 µm Housing material AlMgSi1 / Zn / V4A Protection class IP67 (optional IP67/IP69K; connector version: with mating connector only) Shock EN 60068-2-27:2010, 50 g 11 ms, 100 shocks Vibration EN 60068-2-6:2008, 20 g 10 Hz-2 kHz, 10 cycles Connection 5 pin socket M12 EMC, temperature Refer to output specification Order code bus cable (see page 16) Order code position magnet/slider (see page 8) Order code mounting set (see page 7) Order example: PCQA24 - 1000 - CANOP - L10 - M12/CAN Order Code PCQA24 Model name Measurement range (in mm) 100 ... 5750 (in 10 mm increments) other lengths upon request Output CANOP = CANopen bus CANOP/R = CANopen-Bus with integrated terminating resistance CANJ1939 = CAN SAE J1939 Linearity L02 / L02MM / L10 (for definition see "Specifications" above) Connection M12/CAN = Connector M12, 5 pin DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

POSICHRON® PCQA24 Square Profile Housing Cable output Connector M12 Cable: outer diameter 5.2 mm ±0.2 mm, wire: cross sectional area 0.25 mm² Status Änderungen Datum Name Datum Name Gezeichnet Kontrolliert Norm AS M AUTOMATION SENSORIK MESSTECHNIK ASM GmbH Am Bleichbach 18-22 D-85452 Moosinning Tel.: 08123/986-0 Allgemeintoleranzen Maßstab BMC: Benennung Werkstoff, Halbzeug CT: Zeichnungsnummer / Datei Blatt Nicht bemaßte Werkstückkanten DIN 6784 -0,1 -0,2 +0,1 +0,2 121404_PCQA24-ML(100-5750)-M12_003_LMZ.idw

29.11.2009 ScF

1:1 Maßzeichnung / general drawing 2768-mH PCQA24-ML(100-5750)-(10V|420T)-M12 Zeichnung ist Eigentum der Firma ASM, Vervielfältigung nur mit Genehmigung Schutzvermerk nach DIN 34 beachten © Copyright by ASM GmbH Maße in mm [inch] dimensions in mm [inch] 10,2 [.402] 37,25 [1.467] start position PCMAG5 end position PCMAG5 total length A = measurement length + 155 [6.102] (e.g. 255 [10.039]) mounting set PCQA-BFS1 35,5 [1.3 98] 39 [1.535] 26 [1.024] 54,25 [2.136] 59,25 .333] 46 [1.811] 58 [2.283] 79 12 [.472] ± 15,95 [.628] Status Änderungen Datum Name Datum Name Gezeichnet Kontrolliert Norm AS M AUTOMATION SENSORIK MESSTECHNIK ASM GmbH Am Bleichbach 18-22 D-85452 Moosinning Tel.: 08123/986-0 Allgemeintoleranzen Maßstab BMC: Benennung Werkstoff, Halbzeug CT: Zeichnungsnummer / Datei Blatt Nicht bemaßte Werkstückkanten DIN 6784 -0,1 -0,2 +0,1 +0,2 121404_PCQA24-ML(100-5750)-KAB_001_JMZ.idw

11.05.2005 ScF

1:2 Maßzeichnung 2768-mH PCQA24-ML(100-5750)-(10|420T)-KAB Zeichnung ist Eigentum der Firma ASM, Vervielfältigung nur mit Genehmigung Schutzvermerk nach DIN 34 beachten © Copyright by ASM GmbH 85 [3.346] 46 [1.811] 58 [2.283] 54,2 .136] 59,25 33] 26 [1.024] 39 [1.535] 10,2 [0.402] mounting set PCQA-BFS1 start position PCMAG5 end position PCMAG5 Maße in mm [inch] [0.079 0.039] measurement length (e.g. 100 [3.937]) 70 [2.756] total length A = measurement length + 155 [6.102] (e.g.255 [10.039]) 12 [0.472]± 20,9 [0.823] 37,25 .467] 35,5 [1.3 98] Dimensions informative only. For guaranteed dimensions consult factory.Dimensions in mm [inch] Dimensions informative only. For guaranteed dimensions consult factory.Dimensions in mm [inch] DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

POSICHRON® PCQA24 Square Profile Housing Status Änderungen Datum Name Datum Name Gezeichnet Kontrolliert Norm AS M AUTOMATION SENSORIK MESSTECHNIK ASM GmbH Am Bleichbach 18-22 D-85452 Moosinning Tel.: 08123/986-0 Allgemeintoleranzen Maßstab BMC: Benennung Werkstoff, Halbzeug CT: Zeichnungsnummer / Datei Blatt Nicht bemaßte Werkstückkanten DIN 6784 -0,1 -0,2 +0,1 +0,2 121404_PCQA24-(100-5750)-M12-PCQA BFS1+PCMAG3_002_AMZ.idw 22.04.2008 waneck ISO 1:1 general drawing 2768-mH PCQA24 + Zubehör Zeichnung ist Eigentum der Firma ASM, Vervielfältigung nur mit Genehmigung Schutzvermerk nach DIN 34 beachten © Copyright by ASM GmbH 35,5 [1.3 98] 46 [1.811] 38,3 [1.5 06] 64,5 [2.539] 58 [2.283] PCMAG3 PCMAG3 15,95 [0.628] dimensions in mm [inch] 58 [2.2 83] 39,1 [1.5 28,3 [1.11] measurement length (e.g. 100 [3.937]) total length A = measurement length + 155 [6.102] (e.g. 255[10.041]) 28,3 [1.11] 26,3 [1.0 19,8 [0.78] start position end position PCQA-BFS1 mounting set Dimensions informative only. For guaranteed dimensions consult factory.Dimensions in mm [inch] DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

35 [1.378] 44 [1.732] 24,65 [.97] 26,5 25 [.984]Ø 55 [2.165] 25 [.984] 20 [.787] 17,5 [.6 89] 42,5 [1.673] 5 [.197] 5 [.1 97] 2 [.079] 4x R2,75 [.108] POSICHRON® PCQA Mounting Sets Mounting set PCQA-BFS1 with mounting clamps Option -BFW Mounting brackets for PCQA22 and PCQA24 Note: The option -BFW can only be ordered with a new sensor, not separately! Applicable for sensor lengths up to 1000 mm. Isolation strip Mounting clamp P Isolation sleeve Dimensions informative only. For guaranteed dimensions consult factory. Dimensions in mm [inch] Order example: PCQA24 - 1000 - U2 - P1A - L10 - M12 - BFW DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

9,6 [0.3 78] 26 [1.0 12] 16 [0.6 30] 78 [3.071] Mit eingesetztem Magnet Gesamtlänge A = Messlänge + 155 [6.102] (z.B. 255 [10.041]) 35,5 [1.3 98] 46 [1.811] 58 [2.283] 54,2 5 [2.1 36] 59,2 5 [2.333] 37,2 5 [1.4 67] 26 [1.024] 39 [1.535] 10,2 [0.402] Befestigungssatz PCQA-BFS1 Anfangsposition PCMAG5 Endposition PCMAG5 16 [0.630] ± 12 [0.472] 2 ± [0.0 79 ± 0.0 39] POSICHRON® PCQA Mounting Sets - Magnets PCMAG3 Guided magnet slider with internal position magnet PCMAG5 Standard magnet Internal magnet Dimensions informative only. For guaranteed dimensions consult factory. Dimensions in mm [inch] DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

U1, U2, POSICHRON® Output Specification U2, U8 and I1 Configurable, 1 or 2 channels U1, U2, U8 Voltage output Excitation current Typ. 35 mA, 80 mA max. Output current 2 mA max. Output load > 5 kΩ Resolution 16 bit f.s., min. 10 µm Stability (temperature) ±50 x 10-6 / °C f.s. Protection Reverse polarity, short circuit Output noise 0.5 mVRMS Operating temperature -40 ... +85 °C EMC EN 61326-1:2013 Excitation + Excitation GND Signal 1 + Signal GND Signal diagram Excitation + Excitation GND Signal 1 + Signal GND Current output (3 wire) Excitation current Typ. 60 mA, 80 mA max. Load resistor 350 Ω max. Output current 4 ... 20 mA, 30 mA max (at failure) Resolution 16 bit f.s., min. 10 µm Stability (temperature) ±50 x 10-6 / °C f.s. Protection Reverse polarity, short circuit Output noise 0.5 mVRMS Operating temperature -40 ... +85 °C EMC EN 61326-1:2013 SPAN/ZERO (PMU, as option) Signal 2 + (as option) SPAN/ZERO (PMU, as option) Signal 2 + (as option) Signal diagram Signal diagram DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

POSICHRON® Output Specification U2, U8 and I1 Configurable, 1 or 2 channels Signal Plug connection Cable connection View to the sensor connector Excitation + 1 white Excitation GND 2 brown Signal 1 + 3 green Signal GND 4 yellow Signal 2 + (optional*) 5 grey SPAN/ZERO (PMU** only, optional) 6 pink Connector M12, 8-pin Signal wiring * When using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** Description page 11 Signal Plug connection View to the sensor connector Excitation + 1 Signal 1 + 2 GND 3 Signal 2 + (optional*) 4 PMU** (optional) 5 Connector M12, 5-pin Signal wiring * When using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. Description page 11 Signal Plug connection View to the sensor connector Excitation + 1 Excitation GND 2 Signal + 3 PMU (optional) 4 Connector M8, 4-pin Signal wiring * When using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. ** Description page 11 DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

U1, U2, U8 and I1 Programming of the start and end value by the customer: The option PMU allows to program the start value and the end value of the output range by a programming signal SPAN/ZERO available at the connector. This Signal SPAN/ZERO must be connected with GND via a push button, then position magnet of the sensor must be moved to the start resp. end position. Pushing the button between 2 and 4 seconds sets the actual position as start position, pushing the button more than 5 seconds sets the actual position as end position. The values will be stored and are available after switching off the sensor. To reset the sensor to the factory values the button must be pushed for longer than two seconds when the sensor is switched on. POSICHRON® Description of Output Options Diagnostic on analog outputs Error signal for SSI output If the sensor cannot detect a magnet the position value will assume the maximum value (0xFFFFFFF). Alarm_HIGH (standard) Alarm_LOW (.../U) Alarm_HOLD (.../H) U1 Uout ≥ 10,5 V — keeps last valid state (Order code U1/H) U2 Uout ≥ 10,5 V Uout < 0,25 V (Order code U2/U) keeps last valid state (Order code U2/H) U8 Uout ≥ 10 V Uout < 0,25 V (Order code U8/U) keeps last valid state (Order code U8/H) I1 Iout ≥ 21 mA 1,5 ... 2 mA (Order code I1/U) keeps last valid state (Order code I1/H) Behaviour of the analog signal output in case of error In case of error (magnet missing or outside the measuring range) the analog output signal will assume a state according to the following options: Alarm_HIGH The output voltage resp. the output current is at HIGH level (overrange). Alarm_LOW The output voltage resp. the output current is at LOW level (underrange). Alarm_HOLD The output voltage resp. the output current will keep the last valid state. DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

POSICHRON® Output Specification SSI Description The data transmission takes place by means of the two signals CLOCK and DATA. The pro- cessing unit (PLC, microcomputer) sends pulse sequences which clock the data transmissi- on at the required transfer rate. With the first falling edge of the pulse sequence the position of the sensor is recorded and stored. The following rising edges control the bit-by-bit transfer of the data word. After a delay time the next new position information can be transwithted. Data format (Train of 26 pulses) Synchronous serial interface SSI Output RS422 Excitation voltage 10 ... 36 V DC, residual ripple 10 mVSS Excitation current Typ. 80 mA, 150 mA max. Clock frequency 100 kHz ... 1 MHz Code Gray code, dual code Resolution ≥ 5 µm Delay between pulse trains >25 µs Stability (temperature) ±50 x 10-6 / °C f.s. Operating temperature -40 ... +85 °C EMC EN 61326-1:2013 Sensor circuit Subsequent circuit Cable length Baud rate 50 m 100-1000 kHz 100 m 100-300 kHz Note: Extension of the cable length will reduce the maximum transmission rate. The signals CLOCK/CLOCK and DATA/DATA must be connected in a twisted pair cable, common shielded. CLOCK CLOCK DATA DATA Signal diagram Error indication see page 11. Signal wiring Signal Plug connection Cable connection View to sensor connector Excitation + 1 white Excitation GND 2 brown CLOCK 3 green CLOCK 4 yellow DATA 5 grey DATA 6 pink DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

POSICHRON® Output Specification CANopen Interface CANOP Communication profile CANopen CiA 301 V 4.02, Slave Encoder profile Encoder CiA 406 V 3.2 Error Control Node Guarding, Heartbeat, Emergency Message Node ID Adjustable via LSS or via object dictionary PDO 4 TxPDO, 0 RxPDO, no linking, static mapping PDO Modes Event-/Time triggered, Remote-request, Sync cyclic/acyclic SDO 1 server, 0 client CAM 8 cams Certified Yes Transmission rates 50 kBaud to 1 MBaud, adjustable via LSS or via object dictionary Nodes 127 max. Bus connection M12 connector, 5 pins Integrated bus terminating resistor 120 Ω (option) Bus, galvanic isolated No Description CANopen interface with process data for position and cam functions, programmable are preset, resolution, filtering and cam switching points. Specifications Excitation voltage 18 ... 36 V DC Excitation current Typ. 20 mA for 24 V, max. 80 mA Number of position magnets 1 ... 4 Resolution 50 µm Measuring rate 1 kHz (asynchronous) Stability (temperature) ±50 x 10-6 / °C f.s. Repeatability 1 LSB Operating temperature -40 ... +85 °C Protection Reverse polarity, short circuit Dielectric strength 500 V (V AC, 50 Hz, 1 min.) EMC EN 61326-1:2013 Signal wiring Signal Plug connection Shield 1 Excitation + 2 GND 3 CAN-H 4 CAN-L 5 When using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

POSICHRON® Output Specification CAN SAE J1939 Interface J1939 CAN specification ISO 11898, Basic and Full CAN 2.0 B Transceiver 24V-compliant, not isolated Communication profile SAE J1939 Baud rate 250 kbit/s Internal temination resistor 120 Ω (option) Address Default 247d, configurable Specifications Excitation voltage 18 ... 36 V DC Excitation current Typ. 20 mA for 24 V, max. 80 mA Measuring rate 1 kHz (asynchronous) Stability (temperature) ±50 x 10-6 / °C f.s. Repeatability 1 LSB Operating temperature -40 ... +85 °C Protection Reverse polarity, short circuit Dielectric strength 500 V (V AC, 50 Hz, 1 min.) EMC EN 61326-1:2013 Signal wiring Signal Plug connection Shield 1 Excitation + 2 GND 3 CAN-H 4 CAN-L 5 NAME Fields Arbitrary address capable 0 No Industry group 0 Global Vehicle system 7Fh (127d) Non specific Vehicle system instance 0 Function FFh (255d) Non specific Function instance 0 ECU instance 0 Manufacturer 145h (325d) Manufacturer ID Identity number 0nnn Serial number 21 bit Parameter Group Numbers (PGN) Configuration data PGN EF00h Proprietary-A (PDU1 peer-to-peer) Process data PGN FFnnh Proprietary-B (PDU2 broadcast); nn Group Extension (PS) configurable View to sensor connector When using multiple magnets the distance between two magnets must be min. 70 mm to identify the single magnets definitely. DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

KAB - XM - M12/8F/W - LITZE KAB - XM - M12/8F/W/69K - LITZEIP69K: KAB - XM - M12/5F/G/69K - LITZE KAB - XM - M12/5F/G - LITZE KAB - XM - M12/5F/W/69K - LITZE KAB - XM - M12/5F/W - LITZE KAB - XM - M12/8F/G - LITZE KAB - XM - M12/8F/G/69K - LITZEIP69K: IP69K: IP69K: POSICHRON® Accessories Connector Cables Connector cable M12, 8-pin shielded The 8-lead shielded cable is supplied with a mating 8-pin 90° M12 connector at one end and 8 wires at the other end. Available lengths are 2, 5 and 10 m. Wire: cross sectional area 0.25 mm². Order code: Length in m Signal wiring M12, 8-pin Plug connection / Cable connection 1 2 3 4 5 6 7 8 white brown green yellow grey pink blue red Connector cable M12, 8-pin shielded The 8-lead shielded cable is supplied with a mating 8-pin M12 connector at one end and 8 wires at the other end. Available lengths are 2, 5 and 10 m. Wire: cross sectional area 0.25 mm². Order code: Length in m Connector cable M12, 5-pin shielded The 5-lead shielded cable is supplied with a mating 5-pin 90° M12 connector at one end and 5 wires at the other end. Available lengths are 2 m, 5 m and 10 m. Wire: cross sectional area 0.34 mm Order code: Length in m Connector cable M12, 5-pin shielded The 5-lead shielded cable is supplied with a mating 5-pin M12 connector at one end and 5 wires at the other end. Available lengths are 2 m, 5 m and 10 m. Wire: cross sectional area 0.34 mm Order code: Length in m Signal wiring M12, 5-pin Plug connection / Cable connection 1 2 3 4 5 brown white blue black grey DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com

KAB - XM - M12/5F/G - M12/5M/G - CAN KAB - XM - M12/5F/G/69K - M12/5M/G/69K - CANIP69K: KAB - TCONN - M12/5M - 2M12/5F - CAN KAB - RTERM - M12/5M/G - CAN POSICHRON® Accessories Connector Cables Connector/bus cable M12, 5-pin CAN bus shielded The 5-lead shielded cable is supplied with a female 5-pin M12 connector at one end and a male 5-pin M12 connector at the other end. Available lengths are 0.3 m, 2 m, 5 m and 10 m. Order code: Length in m Terminating resistance M12, 5-pin CAN bus T-piece for bus cable M12, 5-pin CAN bus Order code: Order code: DB-PCQA24-E-2013-11 www.asm-sensor.com © ASM GmbH info@asm-sensor.com