P6KE FUJI | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Dimensions in inches and (millimeters) Version: A06 P6KE SERIES

600 Watts Transient Voltage Suppressor Diodes

/cuspopen UL Recognized File # E-96005 /cuspopen Plastic package has Underwriters Laboratory Flammability Classification 94V-0 /cuspopen Exceeds environmental standards of MIL-STD-19500 /cuspopen 600W surge capability at 10 x 100 us waveform, duty cycle: 0.01% /cuspopen Excellent clamping capability /cuspopen Low zener impedance /cuspopen Fast response time: Typically less than 1.0ps from 0 volts to VBR for unidirectional and 5.0 ns for bidirectional /cuspopen Typical I R less than 1uA above 10V /cuspopen High temperature soldering guaranteed: 260oC / 10 seconds / .375”,(9.5mm) lead length / 5lbs.,(2.3kg) tension M e c h a n i c a l D a t a /cuspopen Case: Molded plastic /cuspopen Lead: Pure tin plated lead free,, solderable per MIL-STD-202, Method 208 /cuspopen Polarity: Color band denotes cathode except bipolar /cuspopen Weight: 0.42gram Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol Value Units Peak Power Dissipation at TA=25 O C, Tp=1ms ( Note 1) PPK Minimum 600 Watts Steady State Power Dissipation at T L=75 o C Lead Lengths .375”, 9.5mm (Note 2) PD 5.0 Watts Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 3) IFSM 100 Amps Maximum Instantaneous Forward Voltage at 50.0A for Unidirectional Only (Note 4) VF 3.5 / 5.0 Volts Operating and Storage Temperature Range TJ, TSTG -55 to + 175 o C Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above T A=25 o C Per Fig. 2. 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minutes Maximum. 4. V F=3.5V for Devices of V BR ≤ 200V and V F=5.0V Max. for Devices of V BR>200V. Devices for Bipolar Applications 1. For Bidirectional Use C or CA Suffix for Types P6KE6.8 through Types P6KE400. 2. Electrical Characteristics Apply in Both Directions.

RATINGS AND CHARACTERISTIC CURVES (P6KE SERIES) Version: A06 FIG.5- TYPICAL JUNCTION CAPACITANCE (UNIDIRECTIONAL) V( ), BREAKDOWN VOLTAGE. VOLTSBR PAC NOITCNUJ, C )Fp(.ECNATICA J VR=0 Tj =25 C f = 1.0MHz Vsig = 50 mVp-p O MEASURED at STAND-OFF VOLTAGE, V WM 1 10 100 200 100 1000 6000 FIG.1- PEAK PULSE POWER RATING CURVE P , PEAK PULSE POWER, KW PPM tp, PULSE WIDTH, sec. 0.1 s 1.0 s 10 s 100 s 1.0ms 10ms 0.1 100 NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 T = 25 C J O FIG.2- PULSE DERATING CURVE PEAK PULSE POWER (P ) or CURRENT (I ) PP PPM TA, AMBIENT TEMPERATURE. ( C) O DERATING IN PERCENT AGE. % 0 25 50 75 100 125 150 175 200 100 FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY IFSM, PEAK FOR WARD SURGE CURRENT NUMBER OF CYCLES AT 60Hz AMPERES 8.3ms Single Half Sine Wave JEDEC Method 1 2 4 6 8 10 20 40 60 80 10010 100 200 FIG.3- PULSE WAVEFORMCLAMPING POWER PEAK PULSE CURRENT t, TIME, ms 0 1.0 2.0 3.0 4.0 100 150 PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of I PPM Half Value - IPPM 10/1000 sec. WAVEFORM as DEFINED by R.E.A. tr = 10 sec Peak Value I PPM td

Dimensions in inches and (millimeters) - 572 - Version: A06 ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Breakdown Voltage Test Stand-Off Maximum Maximum Maximum Maximum Device Nominal VBR Current Voltage Reverse Leakage Peak Pulse Clamping Temperature Voltage (Volts) (Note 1) @IT VWM at VWM Current IRSM Voltage at IPPM Coefficient (Volts) Min Max (mA) (Volts) I D (uA) (Note 2)(Amps) V C(Volts) of V BR(% / OC) P6KE10 P6KE20 P6KE33 P6KE51 P6KE110 P6KE130 P6KE160 P6KE180 P6KE250 P6KE350 Notes: 1. VBR measured after IT applied for 300us, IT=square wave pulse or equivalent. 2. Surge current waverform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. All terms and symbols are consistent with ANSI/IEEE C62.35.