OP4015B MURATA | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
www.RFM.com E-mail: info@rfm.com Page 1 of 3 ©2008-2010 by RF Monolithics, Inc. OP4015B - 2/8/10
Electrical Characteristics
Characteristic Sym Notes Minimum Typical Maximum Units Operating Frequency Absolute Frequency f O 1, 9 780.881 MHz Tuning Frequency Range 2 ±25 ppm Tuning Voltage Range 1 0 +3 V Tuning Linearity 1, 8 ±3 ±5 % Tuning Sensitivity df/dv 2, 10 140 300 ppm/V Modulation Bandwidth 125 265 kHz Q and Q Output Voltage into 50 Ω (VSWR<1.2) V O 1,3 0.60 1.1 V P-P Operating Load VSWR 1,3 2:1 Symmetry 3, 4, 5 49 51 % Harmonic Spurious 3, 4, 6 -30 dBc Nonharmonic Spurious 3, 4, 6, 7 -60 dBc Phase Noise @100 Hz offset -70 dBc/Hz @1 kHz offset -100 dBc/Hz @10 kHz offset -120 dBc/Hz Noise Floor -150 dBc/Hz Q and Q Jitter RMS Jitter (12 kHz to 80 MHz) 3, 4, 6, 7 .20 ps No Noise on VCC 3, 4, 6, 7 10 ps P-P 200 mVP-P from 1 MHz to ½ fO on 3 12 ps P-P Input Impedance (Tuning Port) 1 K Ω Output DC Resistance (between Q & Q )1 , 3 5 0 K Ω DC Power Supply Operating Voltage V CC 1, 3 3.13 3.3, 5.0 5.25 Vdc Operating Current I CC 1, 3 70 mA Operating Case Temperature T C 1, 3 -40 +85 °C Lid Symbolization (YY=Year, WW=Week) RFM OP4015B YYWW SMC-08
- Quartz SAW Stabilized and Filtered “Diff Sine” Technology Fundamental-Mode Oscillation at 780.881 MHz Voltage Tunable for Phase Lock Loop Operations Complies with Directive 2002/95/EC (RoHS) The output of this device is generated and filtered by narrowband quartz SAW elements at 780.881 MHz. The configuration of this clock is intended to provide a pure signal for optical timing applications in noisy signal environments. The Q/Qbar differential output swing of ±1 volt about 0 Vdc has symmetry better than ±1% into loads from 40 to 70 ohms; determined by customer application. The long term frequency accuracy is set by an external reference source allowing this device to complete a Phase Lock Loop design without the usual noise and jitter problems associated with PLL’s. Absolute Maximum Ratings Rating Value Units DC Suppy Voltage 0 to 5.5 Vdc Tuning Voltage 0 to 5.5 Vdc Case Temperature -55 to 100 °C
780.881 MHz
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S. Department of Commerce is required prior to export of this device. Notes: 1. Unless otherwise noted, all specifications include any combination of load VSWR, Vcc, and temperature, with Q and Q terminated into 50 ohm loads to ground. 2. Useful tuning range is in excess of what is required over temp, aging, pushing, pulling & accuracy. 3. The design, manufacturing process, and specifications of this device are subject to change without notice. 4. Only under the nominal conditions of 50 Ω load impedance with VSWR ≤ 1.2 and nominal power supply voltage. 5. Symmetry is defined as the pulse width (in percent of total period) measured at the 50% points of Q or Q (see timing definitions). 6. Jitter and other spurious outputs induced by externally generated electrical noise on V CC or mechanical vibration are not included in this specification, except where noted. External voltage regulation and careful PCB layout are recommended for optimum performance. 7. Applies to period jitter of Q and Q . Measurements are made with the Tektronix CSA803 signal analyzer with at least 1000 samples. 8. Linearity is a function of the percentage variation from a permitted linear deviation versus the amount of frequency tune ran ge (see linearity definition). 9. One or more of the following United States patents apply: 4,616,197; 4,670,681; 4,760,352. /G50 /G62
www.RFM.com E-mail: info@rfm.com Page 2 of 3 ©2008-2010 by RF Monolithics, Inc. OP4015B - 2/8/10 SMC-8 8-Terminal Surface Mount Case Dimension mm Inches MIN MAX MIN MAX A 13.46 13.97 0.530 0.550 B 9.14 9.66 0.360 0.380 C 1.93 Nominal 0.076 Nominal D 3.56 Nominal 0.141 Nominal E 2.24 Nominal 0.088 Nominal F 1.27 Nominal 0.050 Nominal G 2.54 Nominal 0.100 Nominal H 3.05 Nominal 0.120 Nominal J 1.93 Nominal 0.076 Nominal K 5.54 Nominal 0.218 Nominal L 4.32 Nominal 0.170 Nominal M 4.83 Nominal 0.190 Nominal N 0.50 Nominal 0.020 Nominal A B N J L (X2) D (X8) K (X8) C H G M (X3) E F ELECTRICAL CONNECTIONS Terminal Number Connection
1 VCC
3 Enable/Disable
4 Q Output
6 Ground7
8 TUNE Input
Q VCC Buffer AmplifierSAW Oscillator _Vtune Q TOP VIEW OP Performance Curves and Application Information See the OP4005B Data Sheet for typical OP performance curves and application information.
www.RFM.com E-mail: info@rfm.com Page 3 of 3 ©2008-2010 by RF Monolithics, Inc. OP4015B - 2/8/10 W (CARRIER TAPE SIZE) AO BO P (PITCH) COVER TAPE SIZE KO COVER TAPE Orientation in Tape Carrier as Shipped See Detail "A" 13.0 20.22.0 24.4 "C" REF. "B" REF. (measurements in millimeters) Detail "A" SMC-08 Case Reel Size Quantity Per Reel “B” Nominal “C” Nominal Min Max
13 Inch 330 mm 100 mm 200 1000
Carrier Tape Dimensions Cover Tape Size Ao .383 ± .004 (9.7 mm) 21.3 mm Bo .554 ± .004 (14.1 mm) Ko .130 ± .004 (3.3 mm ) P 12 mm W 24 mm Tape Length 60 m Pockets/m 83