GP1S173LCS2F SHARP | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 10

Technical content

Sheet No.: OP13014EN Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. GP1S173LCS2F is a standard, phototransistor output, transmissive photointerrupter with opposing emitter and detector in a case, providing non-contact sensing. For this family of devices, the emitter and detector are inserted in a case, and a 3-pin connector is included to allow remote-mount or off-board designs. 1. Transmissive with phototransistor output 2. Highlights : ・Special position hooks compatible with 3 different Plate thicknesses (1.0, 1.2, 1.6mm) ・Snap insertion 3. Key Parameters : ・Gap Width : 5mm ・Slit Width (detector side) : 0.5mm ・Package : 17 × 12.8 × 8mm (without connector and hooks) ・Connector : Tyco Electronics JAPAN G.K. (173977-3 and 179228-3) 4. RoHS directive compliant 1. Compliant with RoHS directive (2002/95/EC) 1. General purpose detection of object presence or motion. Example : PPC, FAX, Printer ■Description ■Features ■Agency approvals/Compliance ■Applications Gap : 5.0mm Slit : 0.5mm Phototransistor Output, Compact Transmissive Photointerrupter with connector GP1S173LCS2F

Sheet No.: OP13014EN ■Internal Connection Diagram ■Outline Drawing No. CY14032i02A Scale : 2/1 Unit : 1/1 mm Date 10 11 12 13 14 Code A B C D E Date 15 16 17 18 19 Code F G H J K Date 20 21 22 23 24 Code M N O P R Date 25 26 27 28 29 Code S T U W X Date 30 31 Code Y Z Dimension Tolerance less than 5.0 ±0.15 5.0 or more less than 15.0 ±0.2 15.0 or more ±0.3 ① Collector ② GND ③ Anode 1. Unspecified tolerance shall be followed the list below. 2. Dimensions in parenthesis are shown for reference. 3. Coupling and contact : CT receptacle connector (173977-3 and 179228-3) by Tyco Electronics Japan G .K. 4. Date code Y : Year (2012 : 2) Number of the end of the Christian era M : Month (1-9, X, Y , Z) D : Date (1-9, Please refer to a right list other than it.) Note)

Sheet No.: OP13014EN VCC Test pin RL tr tf Input Output 10% 90% ■Absolute maximum ratings Ta=25°C Parameter Symbol Rating Unit Input *1 Forward current IF 50 mA *1, 2 Peak forward current IFM 1 A Reverse voltage VR 5 V Power dissipation P 75 mW Output Collector-emitter voltage VCEO 35 V Emitter-collector voltage VECO 6 V Collector current Ic 20 mA *1 Collector power dissip ation Pc 75 mW *3 Operating temperature Topr -30 to +95 °C Storage temperature Tstg -40 to +100 °C *1 The derating factors of absolute maximum ratings due to ambient temperature are shown in Fig. 1, 2, 3. *2 Pulse width ≦100μs, Duty ratio : 0.01 *3 Connector attachment and release shall be done at normal temperature. ■Electro-optical Characteristics Ta=25°C Parameter Symbol Conditions MIN. TYP. MAX. Unit Input Forward voltage VF IF=20mA - 1.2 1.4 V Peak forward voltage VFM IFM=0.5A - 2 3 V Reverse current IR VR=3V - - 5 μA Output Dark current ICEO VCE=20V - - 100 nA Transfer character- istics Collector current Ic VCE=5V , IF=20mA 0.5 - 15 mA Collector-emitter saturation voltage VCE(sat) IF=40mA, Ic=0.5mA - - 0.4 V Response time (Rise) tr VCE=2V , Ic=2mA RL=100Ω - 3 15 μs (Fall) tf - 4 20 μs (Test circuit for response time)

Sheet No.: OP13014EN Fig.3 Peak forward current vs. duty ratio 200 400 600 800 1000 1200 0.001 0.01 0.1 1 Duty ratio Peak forward current IFM [mA] Fig.2 Collector power dissipation vs. ambient temperature -30 -5 20 45 70 95 120 Ambient temperature Ta [℃] Collector power dissipation Pc [mW] Pulse width ≦100us Ta=25 °C Fig.1 Forward current vs. ambient temperature -30 -5 20 45 70 95 120 Ambient temperature Ta [℃] Forward current IF [mA]

Sheet No.: OP13014EN ■Supplements

  • ODS materials This product shall not contain the following materials. Also, the following materials shall not be used in the production process for this product. Materials for ODS : CFCS, Halon, Carbon tetrachloride 1.1.1-Trichloroethane (Methyl chloroform)
  • Specified brominated flame retardants Specified brominated flame retardants (PBB and PBDE) are not used in this device at all.
  • Country of origin : Philippine or China
  • Product mass : Approx. 1.0g
  • Compliance with each regulation 1) The RoHS directive(2002/95/EC) This product complies with the RoHS directive(2002/95/EC). Object substances: mercury, lead, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE) 2) Content of six substances specified in Management Methods for Control of Pollution Caused by Electronic Information Products Regulation (Chinese : 电子信息产品污染控制管理办法). Category Toxic and hazardous substances Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent chromium (Cr6+) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) ✓: indicates that the content of the toxic and hazardous substance in all the homogeneous materials of the part is below the concentration limit requirement as described in SJ/T 11363-2006 standard.

Sheet No.: OP13014EN 4mm or more ■Notes

  • Circuit design In circuit designing, make allowance for the degradation of the light emitting diode output that results from long continuous operation. (50% degradation/5 years)
  • Position of opaque board Opaque board shall be installed at place 4mm or more from the top of elements. (Example) In case opaque board is the material with an low light blocking effect, There is a possibility of malfunctioning because the light of LED transmits the opaque board. When you design the opaque board, please note transmittance of infrared rays wave length (940nm) and the thickness of the opaque board. And, please adjust the amount of transmitted light to 0.1% or less.
  • Cleaning Please don't carry out immersion cleaning or ultrasonic cleaning to avoid keeping solvent inside case of this device.
  • Washing material Dust and stain shall clean by air blow, or shall clean by soft cloth soaked in washing materials. And washing material to clean shall be used the below materials only. Ethyl alcohol, Methyl alcohol, Isopropyl alcohol
  • Connector connection For the electrical connection to the connector terminal, please certainly use the connector specified in this specifications. Please avoid the connection by the soldering or welding which may damage the main body of the device, and also avoid the contact by the clip and so on which may cause the malfunction by the contact failure. Please avoid the use condition that t it always occurs he vibration in the spot where the connector fits in by the resonance of the sensor and the harness. It may cause the malfunction of the contact failure.
  • Put-in and pull-out of connector The connection other than to the correct connection direction, forcing-into, and the pulling-out diagonally (if being not put-in and pulled-out straight) may deform or break the connector terminal and/or housing, which may cause the unusable state of the device.

Sheet No.: OP13014EN ■Recommended Installation Hole drawing Scale : 2/1 Unit : 1/1mm (Drawing No. CY14033i06) *1 We recommend to fix GP1S173LCS2F at punching side on the fixing plate (metal plate). *2 Plea se decide the final dimensions at your side after confirmation by the actual applications, Because mounting efficiency and mounted stabilization are dependent on mounting plate corner-R and punched state. *3 Tolerance shall be ±0.1mm *4 Please don’t hold connector area but sensor area when fitting in or putting out on the metal plate. Normal mounting type Thickness of plate for 1.6mm Thickness of plate for 1.2mm Thickness of plate for 1.0mm Irregular mounting protection type Thickness of plate for 1.6mm Thickness of plate for 1.2mm Thickness of plate for 1.0mm

Sheet No.: OP13014EN ■Parts This product uses the following parts.

  • Light detector (Quantity : 1) Type Material Maximum sensitivity wavelength (nm) Sensitivity wavelength (nm) Response time (μs) Phototran- sistor Silicon (Si) 930 400 to 1200 3
  • Light emitter (Quantity : 1) Type Material Maximum light emitting wavelength (nm) I/O Frequency (MHz) Infrared light emitting diode (non-coherent) GaAs 940 0.3
  • Material Case Lead flame Black polycarbonate resin (UL 94V-0) Copper Alloy (With plating)
  • Others This product shall not be radiation flux proof. The laser oscillator is not equipped on this product. The terminals are covered with Tin Plating (more than 99.99%).

Sheet No.: OP13014EN ■Packing specification

  • Package No. Name Material Quantity

1 Packing case Corrugated cardboard 1/1000

2 Pad Corrugated cardboard 6/1000

3 Tray Polystyrene 1/200

4 Kraft tape -

  • Packing method 1) 5 products are put in 1 pocket. The longer direction of the product is arranged in the arbitrary direction. 200 products are put in the tray. <Fig.1> 2) The pads are attached at the top and the bottom of the trays and also inserted between the trays. <Fig.2> 3) Seal packing case with Kraft tape. <Fig.3> 4) Indication phase items The contents of the carton indication conforms to EIAJ C-3 and the following items are indicated. Model No., Internal production control name, Quantity, Packing date, Corporate name, Country of origin <Fig.3> (1000pcs. / packing case) (Approximately 2.26kg / packing mass)

Sheet No.: OP13014EN ■Important Notices

  • The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a t hird party resulting from the use of SHARP's devices.
  • Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice.
  • Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii) Measures such as fail -safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii) SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba).
  • If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Law of Japan, it is n ecessary to obtain approval to export such SHARP devices.
  • This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any fo rm or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party.
  • Contact and consult with a SHARP representative if there are any questions about the contents of this publication.