N9020A

N9020A KEYSIGHT | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 20

Technical content

MXA X-Series Signal Analyzer N9020A 10 Hz to 3.6, 8.4, 13.6, or 26.5 GHz Data Sheet

02 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet This data sheet is a summary of the specifications and conditions for MXA signal analyzers. For the complete specifications guide, visit: www.keysight.com/find/mxa_specifications Table of Contents Accelerate to market Every device demands deci - sions that require tradeoffs in your goals—customer specs, throughput, yield. With a high - ly flexible signal analyzer, you can manage and minimize those tradeoffs. Keysight Technologies Inc.’s mid-performance MXA is the ultimate accelerator as your products move from design to the marketplace. It has the flexibility to quickly adapt to your evolving test requirements—today and to - morrow. Maximize your flexibility, and accelerate to market, with the Keysight MXA signal analyzer.

03 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Definitions and Conditions Specifications describe the performance of parameters covered by the product warranty and apply to the full temperature range of 0 to 55 °C 1, unless otherwise noted. 95th percentile values indicate the breadth of the population (approx. 2 σ ) of perfor- mance tolerances expected to be met in 95 percent of the cases with a 95 percent confidence, for any ambient temperature in the range of 20 to 30 °C. In addition to the statistical observations of a sample of instruments, these values include the effects of the uncertainties of external calibration references. These values are not warranted. These values are updated occasionally if a significant change in the statistically observed behavior of production instruments is observed. Typical describes additional product performance information that is not covered by the product warranty. It is performance beyond specifications that 80 percent of the units exhibit with a 95 percent confidence level over the temperature range 20 to 30 °C. Typi - cal performance does not include measurement uncertainty. Nominal values indicate expected performance, or describe product performance that is useful in the application of the product, but are not covered by the product warranty. The analyzer will meet its specifications when: – It is within its calibration cycle – Under auto couple control, except when Auto Sweep Time Rules = Accy – Signal frequencies < 10 MHz, with DC coupling applied – The analyzer has been stored at an ambient temperature within the allowed oper - ating range for at least two hours before being turned on; if it had previously been stored at a temperature range inside the allowed storage range, but outside the allowed operating range – The analyzer has been turned on at least 30 minutes with Auto Align set to normal, or, if Auto Align is set to off or partial, alignments must have been run recently enough to prevent an Alert message; if the Alert condition is changed from Time and Temperature to one of the disabled duration choices, the analyzer may fail to meet specifications without informing the user For the complete specifications guide, visit: www.keysight.com/find/mxa_specifications 1. For earlier instruments (Serial number prefix < MY/SG/US5051), the full temperature ranges from 5 to 50 °C.

04 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Frequency and Time Specifications Frequency range DC coupled AC coupled Option 503 10 Hz to 3.6 GHz 10 MHz to 3.6 GHz Option 508 10 Hz to 8.4 GHz 10 MHz to 8.4 GHz Option 513 10 Hz to 13.6 GHz 10 MHz to 13.6 GHz Option 526 10 Hz to 26.5 GHz 10 MHz to 26.5 GHz Band LO multiple (N) 0 1 10 Hz to 3.6 GHz 1 1 3.5 to 8.4 GHz 2 2 8.3 to 13.6 GHz 3 2 13.5 to 17.1 GHz 4 4 17 to 26.5 GHz Frequency reference Accuracy ± [(time since last adjustment x aging rate) + temperature stability + calibration accuracy] 1 Aging rate Option PFR ± 1 x 10–7 / year ± 1.5 x 10–7 / 2 years Standard ± 1 x 10–6 / year Temperature stability Option PFR Standard – 20 to 30 °C ± 1.5 x 10–8 ± 2 x 10–6 – Full temperature range ± 5 x 10–8 ± 2 x 10–6 Achievable initial calibration accuracy Option PFR ± 4 x 10–8 Standard ± 1.4 x 10 Example frequency reference accuracy (with Option PFR) 1 year after last adjustment = ± (1 x 1 x 10 –7 + 5 x 10–8 + 4 x 10–8) = ± 1.9 x 10–7 Residual FM – Option PFR ≤ (0.25 Hz x N) p-p in 20 ms, nominal – Standard ≤ (10 Hz x N) p-p in 20 ms, nominal See band table above for N (LO multiple) Frequency readout accuracy (start, stop, center, marker) ± (marker frequency x frequency reference accuracy + 0.25 % x span + 5 % x RBW + 2 Hz + 0.5 x horizontal resolution 2) Marker frequency counter Accuracy ± (marker frequency x frequency reference accuracy + 0.100 Hz) Delta counter accuracy ± (delta frequency x frequency reference accuracy + 0.141 Hz) Counter resolution 0.001 Hz Frequency span (FFT and swept mode) Range 0 Hz (zero span), 10 Hz to maximum frequency of instrument Resolution 2 Hz Accuracy – Swept ± (0.25 % x span + horizontal resolution) – FFT ± (0.10 % x span + horizontal resolution) 1. When used with external frequency reference 1 pulse-per-second (PPS), such as the J7203A atomic frequency reference (AFR), the reference tracking ac - curacy needs to be taken into account for calculation of the overall frequency accuracy. Refer to the MXA signal analyzer specifications guide (part number: N9020-90113) for more details. 2. Horizontal resolution is span/(sweep points – 1).

05 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Frequency and Time Specifications (continued) Sweep time and triggering Range Span = 0 Hz Span ≥ 10 Hz 1 μs to 6000 s 1 ms to 4000 s Accuracy Span ≥ 10 Hz, swept Span ≥ 10 Hz, FFT Span = 0 Hz ± 0.01 %, nominal ± 40 %, nominal ± 0.01 %, nominal Trigger Free run, line, video, external 1, external 2, RF burst, periodic timer Trigger delay Span = 0 Hz or FFT Span ≥ 10 Hz, swept Resolution –150 to +500 ms 0 to 500 ms 0.1 μs Time gating – Gate methods – Gate length range (except method = FFT) – Gate delay range – Gate delay jitter Gated LO; gated video; gated FFT 100.0 ns to 5.0 s 0 to 100.0 s 33.3 ns p-p, nominal Sweep (trace) point range All spans 1 to 40001 Resolution bandwidth (RBW) Range (–3.01 dB bandwidth) 1 Hz to 3 MHz (10 % steps), 4, 5, 6, 8 MHz Bandwidth accuracy (power) 1 Hz to 750 kHz 820 kHz to 1.2 MHz (< 3.6 GHz CF) 1.3 to 2 MHz (< 3.6 GHz CF) 2.2 to 3 MHz (< 3.6 GHz CF) 4 to 8 MHz (< 3.6 GHz CF) ± 0.07 dB, nominal ± 0.15 dB, nominal ± 0.25 dB, nominal Bandwidth accuracy (–3.01 dB) – RBW range 1 Hz to 1.3 MHz ± 2 %, nominal Selectivity (–60 dB/–3 dB) 4.1:1, nominal EMI bandwidth (CISPR compliant) 200 Hz, 9 kHz, 120 kHz, 1 MHz (Option EMC or N6141A required) EMI bandwidth (MIL STD 461E compliant) 10 Hz, 100 Hz, 1 kHz, 10 kHz, 100 kHz, 1 MHz (standard) (Option EMC or N6141A required) Analysis bandwidth Maximum bandwidth Option B1X Option B1A Option B85 Option B40 Option B25 (standard) Standard

160 MHz

125 MHz

85 MHz

40 MHz

25 MHz

10 MHz

Video bandwidth (VBW) Range 1 Hz to 3 MHz (10 % steps), 4, 5, 6, 8 MHz, and wide open (labeled 50 MHz) Accuracy ± 6 %, nominal Measurement speed

2 Standard

Local measurement and display update rate 4 ms (250/s) nominal Remote measurement and LAN transfer rate 5 ms (200/s) nominal Marker peak search 1.5 ms, nominal Center frequency tune and transfer (RF) 20 ms, nominal Center frequency tune and transfer (μW) 47 ms, nominal Measurement/mode switching 39 ms, nominal 1. Analysis bandwidth is the instantaneous bandwidth available around a center frequency over which the input signal can be digitized for further analysis or process- ing in the time, frequency, or modulation domain. 2. Sweep points = 101. Apply for instruments with S/N prefix ≥ MY/SG/US4910 or earlier instruments with Option PC2 or PC4. Otherwise, refer to the MXA specification guide.

06 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Amplitude Accuracy and Range Specifications Amplitude range Measurement range Preamp Off Displayed average noise level (DANL) to +30 dBm Preamp On – RF (Opt 503) – Microwave (Opt 508, 513, 526) Displayed average noise level (DANL) to +30 dBm Displayed average noise level (DANL) to +24 dBm Input attenuator range 0 to 70 dB in 2 dB steps Electronic attenuator (Option EA3) Frequency range 10 Hz to 3.6 GHz Attenuation range – Electronic attenuator range – Full attenuation range (mechanical + electronic) 0 to 24 dB, 1 dB steps 0 to 94 dB, 1 dB steps Maximum safe input level Average total power (with and without preamp) +30 dBm (1 W) Peak pulse power < 10 μs pulse width, < 1 % duty cycle +50 dBm (100 W) and input attenuation ≥ 30 dB DC volts – DC coupled – AC coupled ± 0.2 Vdc ± 100 Vdc Display range Log scale 0.1 to 1 dB/division in 0.1 dB steps 1 to 20 dB/division in 1 dB steps (10 display divisions) Linear scale 10 divisions Scale units dBm, dBmV, dBμV, dBmA, dBμA, V, W, A Frequency response Specification 95th percentile (≈ 2 σ) (10 dB input attenuation, 20 to 30 °C, preselector centering applied, σ = nominal standard deviation)

20 Hz to 10 MHz

1 to 3.6 GHz 3.5 to 8.4 GHz 8.3 to 13.6 GHz 13.5 to 22.0 GHz 22.0 to 26.5 GHz ± 0.6 dB ± 0.45 dB ± 1.5 dB ± 2.0 dB ± 2.0 dB ± 2.5 dB ± 0.28 dB ± 0.17 dB ± 0.48 dB ± 0.47 dB ± 0.52 dB ± 0.71 dB Preamp on (0 dB attenuation) 100 kHz to 3.6 GHz 3.5 to 8.4 GHz 8.3 to 13.6 GHz 13.5 to 17.1 GHz 17.0 to 22.0 GHz 22.0 to 26.5 GHz ± 0.75 dB ± 2.0 dB ± 2.3 dB ± 2.5 dB ± 2.5 dB ± 3.5 dB ± 0.28 dB ± 0.67 dB ± 0.73 dB ± 0.97 dB ± 1.36 dB ± 1.48 dB Input attenuation switching uncertainty Specifications Additional information Attenuation > 2 dB, preamp off Relative to 10 dB (reference setting)

50 MHz (reference frequency)

20 Hz to 3.6 GHz 3.5 to 8.4 GHz 8.3 to 13.6 GHz 13.5 to 26.5 GHz ± 0.20 dB ± 0.08 dB, typical ± 0.3 dB, nominal ± 0.5 dB, nominal ± 0.7 dB, nominal ± 0.7 dB, nominal 1. DC coupling required to meet specifications below 50 MHz. With AC coupling, specifications apply at frequencies of 50 MHz and higher. Statistical ob - servations at 10 MHz with AC coupling show that most instruments meet the DC-coupled specifications, however, a small percentage of instruments are expected to have errors exceeding 0.5 dB at 10 MHz at the temperature extreme. The effect at 20 to 50 MHz is negligible but not warranted. 2. Apply for instruments with S/N prefix ≥ MY/SG/US5051. For older instruments, refer to the MXA Specification Guide.

07 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Amplitude Accuracy and Range Specifications (continued) Total absolute amplitude accuracy Specifications (10 dB attenuation, 20 to 30 °C, 1 Hz ≤ RBW ≤ 1 MHz, input signal –10 to –50 dBm, all settings auto-coupled except Auto Swp Time = Accy, any reference level, any scale, σ = nominal standard deviation) At 50 MHz At all frequencies 20 Hz to 3.6 GHz ± 0.33 dB ± (0.33 dB + frequency response) ± 0.23 dB (95th Percentile ≈ 2 σ) Preamp on At all frequencies ± (0.39 dB + frequency response) Input voltage standing wave ratio (VSWR) (≥ 10 dB input attenuation) 10 MHz to 3.6 GHz 3.6 to 8.4 GHz 8.4 to 13.6 GHz 13.6 to 26.5 GHz < 1.2:1, nominal < 1.5:1, nominal < 1.6:1, nominal < 1.9:1, nominal Preamp on (0 dB attenuation) 10 MHz to 3.6 GHz 3.6 to 8.4 GHz 8.4 to 13.6 GHz 13.6 to 26.5 GHz < 1.7:1, nominal < 1.8:1, nominal < 2.0:1, nominal < 2.0:1, nominal Resolution bandwidth switching uncertainty (referenced to 30 kHz RBW) 1 Hz to 1.5 MHz RBW ± 0.05 dB 1.6 MHz to 3 MHz RBW ± 0.10 dB 4, 5, 6, 8 MHz RBW ± 1.0 dB Reference level Range – Log scale –170 to +30 dBm in 0.01 dB steps – Linear scale Same as Log (707 pV to 7.07 V) Accuracy 0 dB Display scale switching uncertainty Switching between linear and log 0 dB Log scale/div switching 0 dB Display scale fidelity Between –10 dBm and –80 dBm input mixer level ± 0.10 dB total Trace detectors Normal, peak, sample, negative peak, log power average, RMS average, and voltage average Preamplifier Frequency range Option P03 Option P08 Option P13 Option P26 100 kHz to 3.6 GHz 100 kHz to 8.4 GHz 100 kHz to 13.6 GHz 100 kHz to 26.5 GHz Gain 100 kHz to 3.6 GHz 3.6 to 26.5 GHz +20 dB, nominal +35 dB, nominal Noise figure 100 kHz to 3.6 GHz 3.6 to 8.4 GHz 8.4 to 13.6 GHz 13.6 to 26.5 GHz 11 dB, nominal 9 dB, nominal 10 dB, nominal 15 dB, nominal

08 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Dynamic Range Specifications 1 dB gain compression (two-tone) Total power at input mixer 20 to 500 MHz 500 MHz to 3.6 GHz 3.6 to 26.5 GHz 0 dBm 3 dBm 0 dBm +3 dBm, nominal +7 dBm, nominal +4 dBm, nominal Preamp on (Option P03, P08, P13, P26) 10 MHz to 3.6 GHz 3.6 to 26.5 GHz – Tone spacing 100 kHz to 20 MHz – Tone spacing > 70 MHz –10 dBm, nominal –26 dBm, nominal –16 dBm, nominal Displayed average noise level (DANL) (Input terminated, sample or average detector, averaging type = Log, 0 dB input attenuation, IF Gain = High, 1 Hz RBW, 20 to 30 °C) Specification Typical 10 Hz 20 Hz 100 Hz 1 kHz 9 kHz to 1 MHz 1 to 10 MHz 10 MHz to 2.1 GHz 2.1 to 3.6 GHz 3.6 to 8.4 GHz 8.4 to 13.6 GHz 13.6 to 17.1 GHz 17.1 to 20.0 GHz 20.0 to 26.5 GHz –150 dBm –151 dBm –149 dBm –149 dBm –148 dBm –144 dBm –143 dBm –136 dBm –95 dBm, nominal –105 dBm, nominal –110 dBm, nominal –120 dBm, nominal –130 dBm –153 dBm –154 dBm –152 dBm –153 dBm –151 dBm –147 dBm –146 dBm –142 dBm Preamp on (Option P03, P08, P13, P26) 100 kHz to 1 MHz 1 to 10 MHz 10 MHz to 2.1 GHz 2.1 to 3.6 GHz 3.6 to 8.4 GHz 8.4 to 13.6 GHz 13.6 to 17.1 GHz 17.1 to 20.0 GHz 20.0 to 26.5 GHz –161 dBm –163 dBm –162 dBm –162 dBm –162 dBm –159 dBm –157 dBm –152 dBm –149 dBm, nominal –163 dBm –166 dBm –164 dBm –166 dBm –165 dBm –163 dBm –161 dBm –157 dBm DANL with Noise Floor Extension (Option NFE 1) on Improvement @ 95th percentile Frequency band Preamp Off Preamp On Band 0, f > 20 MHz 9 dB 10 dB Band 1 8 dB 9 dB Band 2 10 dB 10 dB Band 3 9 dB 10 dB Band 4 9 dB 9 dB Example of effective DANL @ 20 to 30 °C (Option NFE On) Frequency Preamp Off Preamp On Mid-Band 0 (1.8 GHz) –159 dBm –170 dBm Mid-Band 1 (5.9 GHz) –157 dBm –169 dBm Mid-Band 2 (10.95 GHz) –157 dBm –168 dBm Mid-Band 3 (15.3 GHz) –151 dBm –165 dBm Mid-Band 4 (21.75 GHz) –146 dBm –159 dBm 1. Option NFE on MXA is installed as N9020A-NF2, instrument alignment based.

09 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Dynamic Range Specifications (continued) Spurious responses Residual responses (Input terminated and 0 dB attenuation) 200 kHz to 8.4 GHz (swept) Zero span or FFT or other frequencies –100 dBm –100 dBm, nominal Image responses 10 MHz to 3.6 GHz 3.6 to 13.6 GHz 13.6 to 17.1 GHz 17.1 to 22 GHz 22 to 26.5 GHz –80 dBc (–107 dBc, typical) –78 dBc (–88 dBc, typical) –74 dBc (–85 dBc, typical) –70 dBc (–82 dBc, typical) –68 dBc (–78 dBc, typical) LO related spurious (f > 600 MHz from carrier) 10 MHz to 3.6 GHz –90 dBc + 20xlogN 1 typical Other spurious f ≥ 10 MHz from carrier –80 dBc + 20xlogN Second harmonic distortion (SHI) Source frequency Mixer level Distortion SHI 10 MHz to 1.25 GHz 1.25 to 1.8 GHz 1.75 to 7 GHz 7 to 11 GHz 11 to 13.25 GHz –15 dBm –15 dBm –15 dBm –15 dBm –15 dBm –60 dBc –56 dBc –80 dBc –70 dBc –65 dBc +45 dBm +41 dBm +65 dBm +55 dBm +50 dBm Preamp level Distortion SHI Preamp on (Option P03, P08, P13, P26) 10 MHz to 1.8 GHz 1.8 to 13.25 GHz –45 dBm –50 dBm –78 dBc, nominal –60 dBc, nominal +33 dBm, nominal +10 dBm, nominal Third-order intermodulation distortion (TOI) (Two –30 dBm tones at input mixer with tone separation > 5 times IF prefilter bandwidth, 20 to 30 °C, see Specifications Guide for IF prefilter bandwidths) Distortion TOI TOI (typical) 10 to 100 MHz 100 to 400 MHz 400 MHz to 1.7 GHz 1.7 to 3.6 GHz 3.6 to 26.5 GHz –84 dBc –90 dBc –92 dBc –92 dBc –90 dBc +12 dBm +15 dBm +16 dBm +16 dBm +15 dBm +17 dBm +20 dBm +20 dBm +19 dBm +18 dBm Preamp on (two –45 dBm tones at preamp input) 10 to 500 MHz 500 MHz to 3.6 GHz 3.6 to 26.5 GHz –98 dBc, nominal –100 dBc, nominal –70 dBc, nominal +4 dBm, nominal +5 dBm, nominal –15 dBm, nominal 1. N is the LO multiplication factor.

1 MHz

1. Applies for instruments with serial number prefix ≥ MY/SG/US5233. Those instruments ship standard with N9020A-EP2 as the identifier. For nominal values

at other center frequencies, refer to Figure 3. For earlier instruments, refer to the MXA specifications guide. Figure 3. Nominal phase noise at different center frequencies (Applies for instruments with SN prefix ≥ MY/SG/US5233; ships standard

12 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet PowerSuite Measurement Specifications Channel power Amplitude accuracy, W-CDMA or IS95 (20 to 30 °C, attenuation = 10 dB) ± 0.80 dB (± 0.30 dB 95th percentile) Occupied bandwidth Frequency accuracy ± [span/1000] nominal Adjacent channel power Adjacent Alternate Accuracy, W-CDMA (ACLR) (at specific mixer levels and ACLR ranges) – MS ± 0.14 dB ± 0.21 dB – BTS ± 0.49 dB ± 0.44 dB Dynamic range (typical) – Without noise correction –73 dB –79 dB – With noise correction –78 dB –80.5 dB Offset channel pairs measured 1 to 6 ACP measurement and transfer time (fast method) 14 ms, nominal (σ = 0.2 dB) Multiple number of carriers measured Up to 12 Power statistics CCDF Histogram resolution 0.01 dB Harmonic distortion Maximum harmonic number 10th Result Fundamental power (dBm), relative harmonics power (dBc), total harmonic distortion in % Intermod (TOI) Measure the third-order products and intercepts from two tones Burst power Methods Power above threshold, power within burst width Results Single burst output power, average output power, maximum power, minimum power within burst, burst width Spurious emission W-CDMA (1 to 3.6 GHz) table-driven spurious signals; search across regions – Dynamic range – Absolute sensitivity 96.7 dB –84.4 dBm (101.7 dB, typical) (–89.4 dBm, typical) Spectrum emission mask (SEM) cdma2000 ® (750 kHz offset) – Relative dynamic range (30 kHz RBW) – Absolute sensitivity – Relative accuracy 78.9 dB –99.7 dBm ± 0.11 dB (85.0 dB, typical) (–104.7 dBm, typical) 3GPP W-CDMA (2.515 MHz offset) – Relative dynamic range (30 kHz RBW) – Absolute sensitivity – Relative accuracy 81.9 dB –99.7 dBm ± 0.12 dB (88.2 dB, typical) (–104.7 dBm, typical)

13 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet General Specifications Temperature range Operating 0 to 55 °C Storage –40 to 70 °C EMC Complies with European EMC Directive 2004/108/EC – IEC/EN 61326-1 or IEC/EN 61326-2-1 – CISPR Pub 11 Group 1, class A – AS/NZS CISPR 11:2002 – ICES/NMB-001 This ISM device complies with Canadian ICES-001 Cet appareil ISM est conforme à la norme NMB-001 du Canada Safety Complies with European Low Voltage Directive 2006/95EC – IEC/EN 61010-1 3rd Edition – Canada: CSA C22.2 No. 61010-1-12 – U.S.A.: UL 61010-1 3rd Edition Acoustic statement (European Machinery Directive 2002/42/EC, 1.7.4.2u) – Acoustic noise emission – LpA < 70 dB – Operator position – Normal position – Per ISO 7779 Environmental stress Samples of this product have been type tested in accordance with the Keysight Environmental Test Manual and verified to be robust against the environ - mental stresses of storage, transportation, and end-use; those stresses include, but are not limited to, temperature, humidity, shock, vibration, altitude, and power line conditions; test methods are aligned with IEC 60068-2 and levels are similar to MILPRF-28800F Class 3. Power requirements Voltage and frequency 100 to 120 V, 50/60/400 Hz 220 to 240 V, 50/60 Hz Power consumption – On – Standby

465 W maximum

Resolution 1024 x 768, XGA Size 213 mm (8.4 in.) diagonal (nominal) Data storage Internal ≥ 80 GB nominal (removable solid state drive) External Supports USB 2.0 compatible memory devices Weight (without options) Net 16 kg (35 lbs), nominal Shipping 28 kg (62 lbs), nominal Dimensions Height 177 mm (7.0 in) Width 426 mm (16.8 in) Length 368 mm (14.5 in) Warranty The MXA signal analyzer is supplied with a standard 3-year warranty Calibration cycle The recommended calibration cycle is two years; calibration services are available through Keysight service centers

14 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Inputs and Outputs Front panel RF input – Connector Type-N female, 50 Ω, nominal External Mixing (Option EXM) – Connection port – Connector – Impedance – Functions SMA, female 50 Ω, nominal Triplexed for LO output, IF input, and mixer bias – Mixer bias range ± 10 mA in 10 μA step – IF input center frequency – Narrowband IF path – 40 MHz BW IF path – 85, 125, or 160 MHz BW IF path

322.5 MHz

250.0 MHz

300 MHz

– LO output frequency range 3.75 to 14.0 GHz Analog baseband IQ inputs (Option BBA) – Connectors (I, Q, I-Bar, Q-Bar, and Cal Out) BNC female – Cal Out – Signal – Frequency AC coupled square wave Selectable between 1 kHz and 250 kHz – Input impedance (4 connectors: I, Q, I-, Q-) 50 Ω, 1 MΩ (selectable, nominal) – Probes supported – Active probe – Passive probe 1130A, 1131A, 1132A, 1134A 1161A – Input return loss – 50 Ω impedance only selected –35 dB (0 to 10 MHz, nominal) –30 dB (10 to 40 MHz, nominal) Probe power – Voltage/current +15 Vdc, ±7 % at 150 mA max, nominal –12.6 Vdc, ±10 % at 150 mA max, nominal USB 2.0 ports – Master (2 ports) – Standard – Connector – Output current Compatible with USB 2.0 USB type-A female

0.5 A, nominal

10 MHz out

– Connector – Output amplitude – Frequency BNC female, 50 Ω, nominal ≥ 0 dBm, nominal

10 MHz ± (10 MHz x frequency reference accuracy)

– Connector – Input amplitude range – Input frequency – Frequency lock range BNC female, 50 Ω, nominal –5 to 10 dBm, nominal 1 to 50 MHz, nominal ± 2 x 10 –6 of specified external reference input frequency Trigger 1 and 2 inputs – Connector – Impedance – Trigger level range BNC female > 10 kΩ, nominal –5 to 5 V 1. For additional specifications, please refer to the MXA specifications guide. 2. For more details, please refer to the Keysight Probe Configuration Guides, literature numbers 5968-7141EN and 5989-6162EN; probe heads are necessary to attach to your device properly and probe connectivity kits such as E2668B, E2669A. or E2675A are required.

15 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Inputs and Outputs (continued) Rear panel Trigger 1 and 2 outputs – Connector – Impedance – Level BNC female 50 Ω, nominal

5 V TTL, nominal

– Connector – Format – Resolution VGA compatible, 15-pin mini D-SUB XGA (60 Hz vertical sync rates, non-interlaced) Analog RGB 1024 x 768 Noise source drive +28 V (pulsed) – Connector BNC female SNS Series noise source Analog out – Connector BNC female (used with N9063A analog demod app and Option YAS) USB 2.0 ports – Master (4 ports) – Standard – Connector – Output current – Slave (1 port) – Standard – Connector – Output current Compatible with USB 2.0 USB type-A female Compatible with USB 2.0 USB type-B female – Connector – GPIB codes – GPIB mode IEEE-488 bus connector SH1, AH1, T6, SR1, RL1, PP0, DC1, C1, C2, C3, C28, DT1, L4, C0 Controller or device LAN TCP/IP interface – Standard – Connector

1000 Base-T

– Connector – Impedance SMA female, shared by Option CR3 and CRP 50 Ω, nominal Wideband IF output, Option CR3 Center frequency – SA mode or I/Q analyzer – with IF BW ≤ 25 MHz – with Option B40 – with Option B85, B1A, or B1X

250 MHz

Conversion gain –1 to +4 dB (nominal) plus RF frequency response Bandwidth – Low band – High band, with preselector – High band, with preselector bypassed Up to 140 MHz (nominal) Depends on center frequency Up to 410 MHz Programmable IF output, Option CRP Center frequency – Range – Resolution 10 to 75 MHz (user selectable)

0.5 MHz

Conversion gain –1 to +4 dB (nominal) plus RF frequency response Bandwidth – Output at 70 MHz – Low band or high band with preselector bypassed – Preselected band – Lower output frequencies

100 MHz (nominal)

Depends on RF center frequency Subject to folding Residual output signals ≤ –88 dBm (nominal) 1. Option MPB installed and enabled.

16 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet I/Q Analyzer Resolution bandwidth (spectrum measurement) Range – Overall – Span = 1 MHz – Span = 10 kHz – Span = 100 Hz 100 mHz to 3 MHz

50 Hz to 1 MHz

1 Hz to 10 kHz

Flat top, Uniform, Hanning, Gaussian, Blackman, Blackman-Harris, Kaiser Bessel (K-B 70 dB, K-B 90 dB and K-B 110 dB) Analysis bandwidth Standard Option B25 (standard) Option B40 Option B85 Option B1A Option B1X

10 Hz to 10 MHz

10 Hz to 25 MHz

10 Hz to 40 MHz

10 Hz to 85 MHz

10 Hz to 125 MHz

10 Hz to 160 MHz

IF frequency response (standard 10 MHz IF path) IF frequency response (demodulation and FFT response relative to the center frequency, 20 to 30 °C) Center frequency (GHz) Span (MHz) Preselector Max. error RMS (nominal) ≤ 3.6 3.6 < f ≤ 26.5 3.6 < f ≤ 26.5 ≤ 10 ≤ 10 ≤ 10 NA On Off ± 0.40 dB ± 0.45 dB 0.04 dB 0.25 dB 0.04 dB IF phase linearity (deviation from mean phase linearity, nominal) Center frequency (GHz) Span (MHz) Preselector Peak-to-peak RMS ≤ 3.6 3.6 < f ≤ 26.5 3.6 < f ≤ 26.5 ≤ 10 ≤ 10 ≤ 10 NA On Off 1 0.4 ° 1.0 ° 0.4 ° 0.1 ° 0.2 ° 0.1 ° Data acquisition (10 MHz IF path) Time record length – IQ analyzer 4,000,000 IQ sample pairs Sample rate at ADC – Option DP2, B40 or MPB – None of the above

100 MSa/s

90 MSa/s

– Option DP2, B40 or MPB – None of the above 16 bits 14 bits Option B25 (standard) 25 MHz analysis bandwidth IF frequency response (demodulation and FFT response relative to the center frequency, 20 to 30 °C) Center frequency (GHz) Span (MHz) Preselector Max. error RMS (nominal) ≤ 3.6 3.6 < f ≤ 26.5 3.6 < f ≤ 26.5 10 to ≤ 25 10 to ≤ 25 10 to ≤ 25 NA On Off ± 0.45 dB ± 0.45 dB 0.051 dB 0.45 dB 0.05 dB IF phase linearity (deviation from mean phase linearity, nominal) Center frequency (GHz) Span (MHz) Preselector Peak-to-peak RMS 0.02 ≤ f < 3.6 3.6 ≤ f ≤ 26.5 3.6 ≤ f ≤ 26.5 ≤ 25 ≤ 25 ≤ 25 NA On Off 1 0.6 ° 4.5 ° 1.9 ° 0.14 ° 1.2 ° 0.42 ° 1. Option MPB is installed and enabled.

17 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet I/Q Analyzer (continued) Data acquisition (25 MHz IF path) Time record length (IQ pairs) – IQ Analyzer 4,000,000 IQ sample pairs 89600 software 32-bit packing 64-bit packing Memory Option DP2, B40 or MPB 536 MSa 268 MSa 2 GB None of the above 4,000,000 IQ sample pairs (independent of data packing) Sample rate at ADC – Option DP2, B40 or MPB – None of the above – Option DP2, B40 or MPB – None of the above 16 bits 14 bits I/Q Analyzer — Option B40

40 MHz analysis bandwidth, Option B40 is automatically included in Option B85, B1A or B1X

Option B40 40 MHz analysis bandwidth IF frequency response (demodulation and FFT response relative to the center frequency, 20 to 30 °C) Center frequency (GHz) Span (MHz) Preselector RMS (nominal) 0.03 ≤ f < 3.6 3.6 ≤ f ≤ 8.4 8.4 < f ≤ 26.5 ≤ 40 ≤ 40 ≤ 40 NA Off Off 1 ± 0.45 dB ± 0.35 dB ± 0.46 dB ± 0.08 dB ± 0.08 dB ± 0.08 dB IF phase linearity (deviation from mean phase linearity, nominal) Center frequency (GHz) Span (MHz) Preselector Peak-to-peak RMS 0.02 ≤ f < 3.6 3.6 ≤ f ≤ 26.5 NA Off 0.2 ° 5 ° 0.05 ° 1.4 ° Dynamic range (40 MHz IF path) SFDR (Spurious-free dynamic range) – Signal frequency within ± 12 MHz of center –77 dBc, nominal Signal frequency anywhere within analysis BW – Spurious response within ± 18 MHz of center –74 dBc, nominal – Response anywhere within analysis BW –74 dBc, nominal Data acquisition (40 MHz IF path) Time record length (IQ pairs) – IQ Analyzer 4,000,000 samples (I/Q pairs)

89600 VSA software 32-bit packing 64-bit packing

Length (IQ sample pairs) Length (time units)

536 MSa 268 MSa 2 GB total memory, nominal

Samples/(Span x 1.25), nominal Sample rate – At ADC – IQ pairs ADC resolution

200 Msa/s

Span x 1.25, nominal 1. Option MPB is installed and enabled.

18 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet I/Q Analyzer — Option B85/B1A/B1X 85/125/160 MHz analysis bandwidth IF frequency response IF frequency response (20 to 30 °C) Relative to center frequency Center freq. (GHz) Span (MHz) Preselector Typical RMS (nominal) ≥ 0.15, < 3.6 ≤ 85 ≤ 140 ≤ 160 NA NA NA ± 0.6 dB ± 0.6 dB ± 0.17 dB ± 0.25 dB ± 0.2 dB (nomimal) 0.05 dB 0.05 dB 0.07 dB ≥ 3.6, ≤ 8.4 ≤ 85 ≤ 140 ≤ 160 Off Off 1 Off 1 ± 0.73 dB ± 0.8 dB ± 0.2 dB ± 0.35 dB ± 0.3 dB (nomimal) 0.06 dB 0.06 dB 0.07 dB > 8.4, ≤ 26.5 ≤ 85 ≤ 140 ≤ 160 Off Off 1 Off 1 ± 1.10 dB ± 1.40 dB ± 0.50 dB ± 0.76 dB ± 0.5 dB (nomimal) 0.2 dB 0.2 dB 0.12 dB IF phase linearity (deviation from mean phase linearity, nominal) Center freq. (GHz) Span (MHz) Preselector Peak-to-peak RMS ≥ 0.03, < 3.6 ≤ 85 ≤ 140 ≤ 160 NA NA NA 1.6° 3.9° 4.7° 0.54° 0.85° 1.23° ≥ 3.6 ≤ 85 ≤ 160 Off Off 1 4.2° 5.3° 0.93° 1.73° EVM (EVM measurement floor) Customized settings required, preselector bypassed (Option MPB) is installed and enabled Case 1: 802.11ac OFDM signal, 80 MHz bandwidth, MCS8, using 89600 VSA software equalization on, pilot phase tracking post EQ on Carrier frequency, 5.21 GHz; input power, 0 dBm 0.23% (–52.7 dB), nominal 0.35% (–49.1 dB), nominal (EQ on preamble, pilots, and data) (EQ on preamble only) Case 2: 802.11ac OFDM signal, 160 MHz bandwidth, MCS8, using 89600 VSA software equalization on, pilot phase tracking post EQ on Carrier frequency, 5.25 GHz; input power, 0 dBm 0.30% (–50.4 dB), nominal 0.40% (–47.9 dB), nominal (EQ on preamble, pilots, and data) (EQ on preamble only) Dynamic range SFDR (Spurious-free dynamic range) – Signal frequency within ± 12 MHz of center –72 dBc, nominal – Signal frequency anywhere within analysis BW – Spurious response within ± 63 MHz of center –71 dBc, nominal – Response anywhere within analysis BW –69 dBc, nominal Full scale (ADC clipping) Default settings, signal at CF (IF gain = Low: IF gain offset = 0 dB) – Band 0 – Band 1 through 4 –8 dBm mixer level, nominal –7 dBm mixer level, nominal High gain setting, signal at CF (IF gain = High) – Band 0 – Band 1 through 4 –18 dBm mixer level nominal, subject to gain limitations –17 dBm mixer level nominal, subject to gain limitations Effect of signal frequency ≠ CF Up to ± 3 dB, nominal 1. Option MPB is installed and enabled.

19 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet I/Q Analyzer — Option B85/B1A/B1X (continued) 85/125/160 MHz analysis bandwidth Data acquisition (85/125/160 MHz IF path) Time record length – IQ analyzer 4,000,000 IQ sample pairs – 89600 VSA software Data packing 32-bit 64-bit – Length (IQ sample pairs) 536 MSa (2

29 Sa) 268 MSa (228 Sa) 2 GB total memory

– Length (time units) Samples/(span x 1.25) Sample rate – At ADC 400 Msa/s – IQ pairs Span dependent ADC resolution 14 bits Real-Time Spectrum Analyzer (RTSA) 1 Option RT1 or RT2 Real-time analysis Real-time analysis bandwidth – Option RT1 – Option RT2 Up to 160 MHz Up to 160 MHz Analysis BW option determines the max real-time bandwidth Analysis BW option determines the max real-time bandwidth Minimum detectable signal duration with > 60 dB StM 2 ratio – Option RT1 – Option RT2 11.42 ns 5.0 ns Minimum signal duration with 100% probability of Frequency Mask Triggering (FMT) at full amplitude accuracy – Option RT1 – Option RT2 17.3 μs 3.57 μs Signal is at mask level Signal is at mask level Minimum acquisition time FFT rate Supported triggers 100 μs 292,969/s Level, Level with time qualified (TQT), Line, External, RF burst, Frame, Frequency mask (FMT), FMT with TQT 1. For additional RTSA specifications, please refer to Option RT1/RT2 Chapter in the MXA Signal Analyzer specifications guide (part number: N9020-90113) 2. StM = “Signal-to-Mask”

20 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. www.lxistandard.org LAN eXtensions for Instruments puts the power of Ethernet and the Web inside your test systems. Keysight is a founding member of the LXI consortium. Three-Year Warranty www.keysight.com/find/ThreeYearWarranty Keysight’s commitment to superior product quality and lower total cost of ownership. The only test and measurement company with three-year warranty standard on all instruments, worldwide. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to five years of protection and no budgetary surprises to ensure your instruments are operating to specification so you can rely on accurate measurements. www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2008 Quality Management System Keysight Channel Partners www.keysight.com/find/channelpartners Get the best of both worlds: Keysight’s measurement expertise and product breadth, combined with channel partner convenience. cdma2000 ® is a registered certification mark of the Telecommunications Industry Association. www.keysight.com/find/mxa This information is subject to change without notice. © Keysight Technologies, 2011 - 2015 Published in USA, February 21, 2015 5989-4942EN www.keysight.com For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada (877) 894 4414 Brazil 55 11 3351 7010 Mexico 001 800 254 2440 United States (800) 829 4444 Asia Pacific Australia 1 800 629 485 China 800 810 0189 Hong Kong 800 938 693 India 1 800 112 929 Japan 0120 (421) 345 Korea 080 769 0800 Malaysia 1 800 888 848 Singapore 1 800 375 8100 Taiwan 0800 047 866 Other AP Countries (65) 6375 8100 Europe & Middle East Austria 0800 001122 Belgium 0800 58580 Finland 0800 523252 France 0805 980333 Germany 0800 6270999 Ireland 1800 832700 Israel 1 809 343051 Italy 800 599100 Luxembourg +32 800 58580 Netherlands 0800 0233200 Russia 8800 5009286 Spain 800 000154 Sweden 0200 882255 Switzerland 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) United Kingdom 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-09-23-14)