DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 21
Technical content
Release Date: Sep. 2015 - 1 - Version A1.1 NuVoice® N575F145 Data Sheet
Release Date: Sep. 2015 - 2 - Version A1.1 Table of Contents
Release Date: Sep. 2015 - 3 - Version A1.1
1 GENERAL DESCRIPTION
The N575F145 is a sy stem-on-chip product optimized for low power, audio record and playback with an embedded ARM® Cortex™-M0 32-bit microcontroller core. The N575F145 embeds a Cortex™ -M0 core run ning up t o 49 MHz with 145 KBytes of non-volatile flash memory and 12 KBytes of embedded SRAM. It also comes equipped with a variety of peripheral devices, such as Timers, Watchdog Timer (WDT), Real -time Clock (RTC), Peripheral Direct Memory Access ( PDMA), a variety of serial interfaces (UART, SPI/SSP, I 2C, I2S), PWM modulators, GPIO, Analog Comparator, Low Voltage Detector and Brown-out detector. The N575F145 comes equipped with a rich set of power saving modes including a Deep Power Down (DPD) mode drawing less than 1 A. A micro -power 16 KHz oscillator can periodically wake up the device from deep power down to check for other events. A Standby Power Down (SPD) mode can maintain a real time clock function at less than 10A. For audio functionality the N575F145 includes a Sigma -Delta ADC with 92 dB SNR performance coupled with a Prog rammable Gain Amplifier (PGA) capable of a maximum gain of 61 dB to enable direct connection of a microphone. Audio output is provided by a Differential Class D amplifier (DPWM) that can deliver 1W1 of power to an 8Ω speaker. The N575F145 provides eight an alog enabled general purpose IO pins (GPIO). These pins can be configured to connect to an analog comparator, can be configured as analog current sources or can be routed to the SDADC for analog conversion. They can also be used as a relaxation oscillator to perform capacitive touch sensing.
1 We suggest implementing thermal prote ction by utilizing the Temperature Alarm; for details please
refer to Temperature Alarm in Design Guide.
Release Date: Sep. 2015 - 4 - Version A1.1
2 FEATURES
Core – ARM® Cortex™-M0 core runs up to 49 MHz. – One 24-bit System tick timer for operating system support. – Supports a variety of low power sleep and power down modes. – Single-cycle 32-bit hardware multiplier. – NVIC (Nested Vector Interrupt Controller) for 32 interrupt inputs, each with 4-levels of priority. – Serial Wire Debug (SWD) support with 2 watchpoints/4 breakpoints. Power Management – Wide operating voltage range from 2.4V to 5.5V. – Power management Unit (PMU) providing four levels of power control. – Deep Power Down (DPD) mode with sub micro-amp leakage (<1µA). – Wakeup from Deep Power Down via dedicated WAKEUP pin or timed operation from internal low power 16 KHz oscillator. – Standby mode with limited RAM retention and RTC operation (<10µA). – Wakeup from Standby can be from any GPIO interrupt, RTC or BOD. – Sleep mode with minimal dynamic power consumption. – 3V LDO for operation of external 3V devices such as serial flash. Flash EPROM Memory – 145 KBytes Flash EPROM for program code and data storage. – 4 KBytes of flash can be configured as boot sector for ISP loader. – Support In-system program (ISP) and In-circuit program (ICP) application code update – 1 KBytes page erase for flash – Configurable boundary to delineate code and data flash. – Support 2 wire In-circuit Programming (ICP) update from SWD ICE interface SRAM Memory – 12 KBytes embedded SRAM. Clock Control – One high speed and two low speed oscillators providing flexible selection for different applications. No external components necessary. – Built-in trimmable oscillator with range of 16 ~ 49 MHz. Factory trimmed within 1% to settings of 49.152 MHz and 32.768 MHz. User trimmable with in-built frequency measurement block (OSCFM) using reference clock of 32 KHz crystal or external reference source. – Ultra-low power (<1uA) 16 KHz oscillator for watchdog and wakeup from power-down or sleep operation. – External 32 KHz crystal input for RTC function and low power system operation. GPIO – Four I/O modes: Quasi bi-direction Push-Pull output Open-Drain output Input only with high impendence – TTL/Schmitt trigger input selectable. – I/O pin can be configured as interrupt source with edge/level setting. – Switchable pull-up. Audio Analog to Digital converter – Sigma Delta ADC with configurable decimation filter and 16 bit output.
Release Date: Sep. 2015 - 5 - Version A1.1 – 92 dB Signal-to-Noise (SNR) performance. – Programmable gain amplifier with 32 steps from -12 to 35.25 dB in 0.75 dB steps. – Boost gain stage of 26 dB, giving maximum total gain of 61 dB. – Input selectable from dedicated MIC pins or analog enabled GPIO. – Programmable biquad filter to support multiple sample rates from 8 ~ 32 KHz. – DMA support for minimal CPU intervention. Differential Audio PWM Output (DPWM) – Direct connection of speaker – 1W drive capability into 8Ω load – Configurable up-sampling to support sample rates from 8 ~ 32 KHz – DMA support for minimal CPU intervention. Timers – Two timers with 8-bit pre-scalar and 24-bit resolution. – Counter auto reload. Watch Dog Timer – Default ON/OFF by configuration setting – Multiple clock sources – 8 selectable time out period from micro seconds to seconds (depending on clock source) – WDT can wake up power down/sleep. – Interrupt or reset selectable on watchdog time-out. RTC – Real Time Clock counter (second, minute, hour) and calendar counter (day, month, year) – Alarm registers (second, minute, hour, day, month, year) – Selectable 12-hour or 24-hour mode – Automatic leap year recognition – Time tick and alarm interrupts. – Device wake up function. – Supports software compensation of crystal frequency by compensation register (FCR) PWM/Capture – Built-in up to two 16-bit PWM generators provide two PWM outputs or one complementary paired PWM outputs. – The PWM generator equipped with a clock source selector, a clock divider, an 8-bit pre-scaler and Dead-Zone generator for complementary paired PWM. – PWM interrupt synchronous to PWM period. – 16-bit digital Capture timers (shared with PWM timers) provide rising/falling capture inputs. – Support Capture interrupt UART – UART ports with flow control (TX, RX, CTS and RTS) – 8-Byte FIFO. – Support IrDA (SIR) and LIN function – Programmable baud-rate generator up to 1/16 of system clock. SPI – Master up to 20 Mbps / Slave up to 10 Mbps. – Support MICROWIRE/SPI master/slave mode (SSP) – Full duplex synchronous serial data transfer – Variable length of transfer data from 1 to 32 bits – MSB or LSB first data transfer – 2 slave/device select lines when used in master mode. – Hardware CRC calculation module available for CRC calculation of data stream.
Release Date: Sep. 2015 - 6 - Version A1.1 – DMA support for burst transfers. I2C – Master/Slave up to 1Mbit/s – Bidirectional data transfer between masters and slaves – Multi-master bus (no central master). – Arbitration between simultaneously transmitting masters without corruption of serial data on the bus – Serial clock synchronization allows devices with different bit rates to communicate via one serial bus. – Serial clock synchronization can be used as a handshake mechanism to suspend and resume serial transfer. – Programmable clock allowing versatile rate control. – I2C -bus controller supports multiple address recognition. I2S – Interface with external audio CODEC. – Operate as either master or slave. – Capable of handling 8, 16, 24 and 32 bit word sizes – Mono and stereo audio data supported – I2S and MSB justified data format supported – Two 8 word FIFO data buffers are provided, one for transmit and one for receive – Generates interrupt requests when buffer levels cross a programmable boundary – Supports DMA requests, for transmit and receive Brown-out detector – Supports time-multiplex operation to minimize power consumption. – Supports Brownout Interrupt and Reset option Built in Low Dropout Voltage Regulator (LDO) – Capable of delivering 30mA load current. – Configurable for output voltage of 1.8V, 2.4V, 3.0V and 3.3V – Eight GPIO (GPIOA<7:0>) operate from LDO voltage domain allowing direct interface to, for example, 3V SPI Flash. – Can be bypassed and voltage domain supplied directly from system power. Additional Features – Over temperature alarm. Can generate interrupt if device exceeds safe operating temperature. – Temperature proportional voltage source which can be routed to ADC for temperature measurements. – Digital Microphone interface. Operating Temperature: -20C ~ 85C
Release Date: Sep. 2015 - 7 - Version A1.1
3 PAD DESCRIPTION
Pin Name Pin Type Alt CFG Description WAKEUP I Pull low to wake part from deep power down PB.7 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 7 I2S_SDO O 1 Serial Data Output for I2S interface CMP7 AIO 2 Configure as relaxation oscillator for capacitive touch sensing PB.6 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 6 I2S_SDI I 1 Serial Data Input for I2S interface CMP6 AIO 2 Configure as relaxation oscillator for capacitive touch sensing SPI_MOSI1 O 3 Master Out, Slave In channel 1 for SPI interface PB.5 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 5 PWM1B O 1 PWM channel 1 complementary output pin CMP5 AIO 2 Configure as relaxation oscillator for capacitive touch sensing SPI_MISO1 I 3 Master In, Slave Out channel 1 for SPI interface PB.4 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 4 PWM0B O 1 PWM channel 0 complementary output pin CMP4 AIO 2 Configure as relaxation oscillator for capacitive touch sensing SPI_MOSI0 O 3 Master Out, Slave In channel 0 for SPI interface PB.3 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 3 I2C_SDA I/O 1 Serial Data, I2C interface CMP3 AIO 2 Configure as relaxation oscillator for capacitive touch sensing SPI_MISO0 I 3 Master In, Slave Out channel 0 for SPI interface PB.2 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 2 I2C_SCL I/O 1 Serial Clock, I2C interface
Release Date: Sep. 2015 - 8 - Version A1.1 Pin Name Pin Type Alt CFG Description CMP2 AIO 2 Configure as relaxation oscillator for capacitive touch sensing SPI_SCLK I/O 3 Serial Clock for SPI interface PB.1 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 1. Triggers external interrupt 1 (EINT1/IRQ3) MCLK O 1 Master clock output for synchronizing external device CMP1 AIO 2 Configure as relaxation oscillator for capacitive touch sensing SPI_SSB1 O 3 Slave Select Bar 1 for SPI interface PB.0 A/I/O 0 General purpose input/output pin, analog capable; Port B, bit 0. Triggers external interrupt 0 (EINT0/IRQ2) SPI_SSB1 O 3 Slave Select Bar 1 for SPI interface CMP0 AIO 2 Configure as relaxation oscillator for capacitive touch sensing SPI_SSB0 I/O 3 Slave Select Bar 0 for SPI interface VCCD P Main Digital Supply for Chip. Supplies all IO except analog, Speaker Driver and PA<7:0> VREG P Logic regulator output decoupling pin. A 1µF capacitor returning to VSSD must be placed on this pin. NC Should remain unconnected. NC Should remain unconnected. PA.15 I/O 0 General purpose input/output pin; Port A, bit 15 TM1 I 1 External input to Timer 1 SDIN I 2 Sigma Delta bit stream input for digital MIC mode PA.9 I/O 0 General purpose input/output pin; Port A, bit 9 UART_RX I 1 Receive channel of UART I2S_BCLK I/O 2 Bit Clock for I2S interface PA.8 I/O 0 General purpose input/output pin; Port A, bit 8 UART_TX O 1 Transmit channel of UART I2S_FS I/O 2 Frame Sync Clock for I2S interface VCCSPK P Power Supply for PWM Speaker Driver SPK+ O Positive Speaker Driver Output VSSSPK P Ground for PWM Speaker Driver SPK- O Negative Speaker Driver Output
Release Date: Sep. 2015 - 9 - Version A1.1 Pin Name Pin Type Alt CFG Description VCCSPK P Power Supply for PWM Speaker Driver RESETN I External reset input. Pull this pin low to reset device to initial state. Has internal weak pull-up. ICE_DAT I/O Serial Wire Debug port data pin. Has internal weak pull- up. ICE_CLK I Serial Wire Debug port clock pin. Has internal weak pull- up. VSSD P Digital Ground. PA.7 I/O 0 General purpose input/output pin; Port A, bit 7 I2S_SDO O 1 Serial Data Out for I2S interface PA.6 I/O 0 General purpose input/output pin; Port A, bit 6 I2S_SDI I 1 Serial Data In for I2S interface PA.5 I/O 0 General purpose input/output pin; Port A, bit 5 I2S_BCLK I/O 1 Bit Clock for I2S interface PA.4 I/O 0 General purpose input/output pin; Port A, bit 4 I2S_FS I/O 1 Frame Sync Clock for I2S interface PA.3 I/O 0 General purpose input/output pin; Port A, bit 3 SPI_MISO0 I 1 Master In, Slave Out channel 0 for SPI interface I2C_SDA I/O 2 Serial Data, I2C interface PA.2 I/O 0 General purpose input/output pin; Port A, bit 2 SPI_SSB0 I/O 1 Slave Select Bar 0 for SPI interface VDD33 P LDO Regulator Output. If used, a 1µF capacitor must be placed to ground. If not used then tie to VCCD. PA.1 I/O 0 General purpose input/output pin; Port A, bit 1 SPI_SCLK I/O 1 Serial Clock for SPI interface I2C_SCL I/O 2 Serial Clock, I2C interface PA.0 I/O 0 General purpose input/output pin; Port A, bit 2 SPI_MOSI0 O 1 Master Out, Slave In channel 0 for SPI interface MCLK O 2 Master clock output. VCCLDO P Power Supply for LDO, should be connected to VCCD PA.14 I/O 0 General purpose input/output pin; Port A, bit 14 SDCLK O 1 Clock output for digital microphone mode. SDCLKn O 2 Inverse Clock output for digital microphone mode.
Release Date: Sep. 2015 - 10 - Version A1.1 Pin Name Pin Type Alt CFG Description PA.13 I/O 0 General purpose input/output pin; Port A, bit 13 PWM1 O 1 PWM1 Output. SPKM O 2 Equivalent to SPK-. I2S_BCLK I/O 3 Bit Clock for I2S interface PA.12 I/O 0 General purpose input/output pin; Port A, bit 12 PWM0 O 1 PWM0 Output. SPKP O 2 Equivalent to SPK+ I2S_FS I/O 3 Frame Sync Clock for I2S interface XO32K O 32.768 KHz Crystal Oscillator Output XI32K I 32.768 KHz Crystal Oscillator Input. Max Voltage 1.8V VSSA AP Ground for analog circuitry. VMID O Mid rail reference. Connect 4.7µF to VSSA. MIC+ AI Positive microphone input. MIC- AI Negative microphone input. MICBIAS AO Microphone bias output. VCCA AP Analog power supply. PA.11 I/O 0 General purpose input/output pin; Port A, bit 11 I2C_SCL I/O 1 Serial Clock, I2C interface I2S _SDO O 2 Serial Data Out I2S interface UART_CTSn I 3 UART Clear to Send Input. PA.10 I/O 0 General purpose input/output pin; Port A, bit 10 I2C _SDA I/O 1 Serial Data, I2C interface I2S_SDI I 2 Serial Data In I2S interface UART_RTSn O 3 UART Request to Send Output. Note: PAD Type I=Digital Input, O=Digital Output; AI=Analog Input; P=Power PAD; AP=Analog Power
Release Date: Sep. 2015 - 11 - Version A1.1
4 BLOCK DIAGRAM
50MHz Internal Osc. 32kHz RTC Osc Audio ADCUART WDTI2S LDO 3.0V LDO 1.8V BOD PDMA POR 10kHz low power Osc Peripherals with PDMA Figure 4-1 N575F145 Block Diagram
Release Date: Sep. 2015 - 12 - Version A1.1
5 APPLICATION DIAGRAM
Release Date: Sep. 2015 - 13 - Version A1.1
6 ELECTRICAL CHARACTERISTICS
6.1 Absolute Maximum Ratings
Symbol Parameter Min Max Unit DC Power Supply VDDVSS -0.3 +6.0 V Input Voltage VIN VSS-0.3 VDD+0.3 V Oscillator Frequency 1/tCLCL 0 40 MHz Operating Temperature TA -40 +85 C Storage Temperature TST -55 +150 C Maximum Current into VDD - 120 mA Maximum Current out of VSS 120 mA Maximum Current sunk by a I/O pin 35 mA Maximum Current sourced by a I/O pin 35 mA Maximum Current sunk by total I/O pins 100 mA Maximum Current sourced by total I/O pins 100 mA Note: Exposure to conditio ns beyond those listed under absolute maximum ratings may adversely affects the lift and reliability of the device.
Release Date: Sep. 2015 - 14 - Version A1.1
6.2 DC Electrical Characteristics
(VDD-VSS=3.3V, TA = 25C, FOSC = 49.152 MHz unless otherwise specified.) Parameter Sym Specification Test Conditions Min Typ Max Unit Operation voltage VDD 2.4 5.5 V VDD =2.4V ~ 5.5V up to 49 MHz Power Ground VSS AVSS -0.3 V Analog Operating Voltage AVDD 0 VDD V Analog Reference Voltage Vref 0 AVDD V Operating Current Normal Run Mode @ 49.152 MHz IDD1 24.8 mA VDD= 5.5V, Enable all IP. IDD2 19.7 mA VDD=5.5V, disable all IP IDD3 23.6 mA VDD = 3V, enable all IP IDD4 18.3 mA VDD = 3V, disable all IP Operating Current Normal Run Mode @ 32.768 MHz IDD5 18.8 mA VDD = 5.5V, Enable all IP. IDD6 15.0 mA VDD = 5.5V, Disable all IP. IDD7 17.6 mA VDD = 3V, Enable all IP. IDD8 13.8 mA VDD = 3V, Disable all IP.
Release Date: Sep. 2015 - 15 - Version A1.1 Operating Current Normal Run Mode @ 12.288 MHz IDD9 12.5 mA VDD = 5.5V enable all IP IDD10 10.3 mA VDD = 5.5V, disable all IP IDD11 11.4 mA VDD = 3V enable all IP IDD12 9 mA VDD = 3V, disable all Operating Current Normal Run Mode @ 4.9152 MHz IDD13 9.7 mA VDD = 5.5V, Enable all IP. IDD14 8.1 mA VDD = 5.5V, Disable all IP. IDD15 8.7 mA VDD = 3V, Enable all IP. IDD16 7.0 mA VDD = 3V, Disable all IP. Operating Current Sleep Mode IIDLE1 10 mA VDD= 5.5V IIDLE1 9 mA VDD= 3.3V Operating Current Deep Sleep Mode IIDLE1 10 mA VDD=5.5V IIDLE1 8 mA VDD= 3.3V Standby Power down mode(SPD) IIDLE1 3 uA VDD=3.3V 32K running with RTC IIDLE1 1 uA VDD= 3.3V 16K running Operating Current Deep Power down mode(DPD) IIDLE1 500 nA VDD=3.3V Wakeup with16K IIDLE1 nA VDD= 3.3V wakeup with wakeup pin
Release Date: Sep. 2015 - 16 - Version A1.1 Input Current PA, PB (Quasi-bidirectional mode) IIN1 -60 - +15 A VDD = 5.5V, VIN = 0V or VIN=VDD Input Current at /RESET [1] IIN2 -55 -45 -30 A VDD = 3.3V, VIN = 0.45V Input Leakage Current PA, PB ILK -2 - +2 A VDD = 5.5V, 0<VIN<VDD Logic 1 to 0 Transition Current PA~PB (Quasi-bidirectional mode) ITL Input Low Voltage PA, PB (TTL input) VIL1 -0.3 - 0.8 V VDD = 4.5V Input High Voltage PA, PB (TTL input) VIH1 2.0 - VDD +0.2 V VDD = 5.5V 1.5 - VDD +0.2 VDD =3.0V Input Low Voltage XT1[*2] VIL3 0 - 0.8 V VDD = 4.5V 0 - 0.4 VDD = 3.0V Input High Voltage XT1[*2] VIH3 3.5 - VDD +0.2 V VDD = 5.5V 2.4 - VDD +0.2 VDD = 3.0V Input Low Voltage X32I[*2] VIL4 0 - 0.4 V Input High Voltage X32I[*2] VIH4 1.7 2.5 V Negative going threshold (Schmitt input), /REST VILS -0.5 - 0.3VDD V Positive going threshold (Schmitt input), /REST VIHS 0.7VDD - VDD+0. 5 V Hysteresis voltage of PA~PB(Schmitt input) VHY 0.2VDD V
Release Date: Sep. 2015 - 17 - Version A1.1 Source Current PA, PB (Quasi-bidirectional Mode) ISR11 -300 -370 -450 A VDD = 4.5V, VS = 2.4V ISR12 -50 -70 -90 A VDD = 2.7V, VS = 2.2V ISR12 -40 -60 -80 A VDD = 2.5V, VS = 2.0V Source Current PA, PB (Push-pull Mode) ISR21 -20 -24 -28 mA VDD = 4.5V, VS = 2.4V ISR22 -4 -6 -8 mA VDD = 2.7V, VS = 2.2V ISR22 -3 -5 -7 mA VDD = 2.5V, VS = 2.0V Sink Current PA, PB (Quasi-bidirectional and Push- pull Mode) ISK1 10 16 20 mA VDD = 4.5V, VS = 0.45V ISK1 7 10 13 mA VDD = 2.7V, VS = 0.45V ISK1 6 9 12 mA VDD = 2.5V, VS = 0.45V Brownout voltage with BOV_VL [2:0] =000b VBO2.1 2.15 V Brownout voltage with BOV_VL [2:0] =001b VBO2.2 2.25 V Brownout voltage with BOV_VL [2:0] =010b VBO2.4 2.45 V Brownout voltage with BOV_VL [2:0] =011b VBO2.5 2.55 V Brownout voltage with BOV_VL [2:0] =100b VBO2.7 2.7 V Brownout voltage with BOV_VL [2:0] =101b VBO2.8 2.8 V Brownout voltage with BOV_VL [2:0] =110b VBO3.0 3.0 V Brownout voltage with BOV_VL [2:0] =111b VBO4.5 4.55 V Notes: 1. /RESET pin is a Schmitt trigger input. 2. Crystal Input is a CMOS input.
Release Date: Sep. 2015 - 18 - Version A1.1
6.3 AC Electrical Characteristics
6.3.1 External 32 KHz XTAL Oscillator
Parameter Condition Min Typ Max Unit Input clock frequency External crystal - 32.768 - KHz Temperature - -40 - 85 ℃ VDD - 2.4 - 5.5 V 6.3.2 Internal 49.152 MHz Oscillator Parameter Condition Min Typ Max Unit Supply voltage[1] - 2.4 - 5.5 V Center Frequency - - 49.152 MHz Calibrated Internal Oscillator Frequency -40C ~ +85C; VDD=2.5V~5.5V -4 - 4 %
6.3.3 Internal 16 KHz Oscillator
Parameter Condition Min Typ Max Unit Supply voltage - 2.4 - 5.5 V Center Frequency - - 10 - KHz Calibrated Internal Oscillator Frequency -40C ~ +85C; Notes: *1. Internal operation voltage comes from LDO.
6.3.4 Reset Characteristics
(VDD-VSS=5V, TA = 25C, FOSC = 49.152 MHz unless otherwise specified.) Parameter No. Parameter Parameter Name Min Typ Max Unit R1 VTH Reset threshold 1 1.7 2 V R2 TVDDRISE Supply voltage (VDD) rise time (0V-5V), power on reset - - 100 ms R3 TPOR Power-On Reset timeout - - 12 µs R4 TIRPOR Internal reset timeout after POR - - 45 µs R5 TMIN Minimum RESETN pulse width 100 - - ns R6 TIRHWR Internal reset timeout after hardware reset (RESETN pin) - - 20 µs
Release Date: Sep. 2015 - 19 - Version A1.1 R7 TIRSWR Internal reset timeout after software- initiated system reset - - 2 µs R8 TIRWDR Internal reset timeout after watchdog reset - - 3 *2 µs *Notes: 2. It will be 6500us when use OSC_10K as the WDG clock.
6.3.4.1 Power-On Reset Timing
(Internal) Reset (Internal)
6.3.4.2 External Reset Timing (RESETN)
(Internal) RESETN R5 R6
6.3.4.3 Software Reset Timing
(Internal) SW Reset
6.3.4.4 Watchdog Reset Timing
(Internal) WDOG Reset (Internal)
Release Date: Sep. 2015 - 20 - Version A1.1
7 ORDERING INFORMATION
Die form: N575F145 (Blank) Die form: N575F145xxxx (Pre-code)
8 REVISION HISTORY
Version Date Substantial Changes Page A1.0 July 2015 Initial Release A1.1 Sep. 2015 Remove package form All
Release Date: Sep. 2015 - 21 - Version A1.1 Important Notice Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any malfunction or failure of which may cause loss of human life, bodily injury or severe property damage. Such applications are deemed, “Insecure Usage”. Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy control instruments, airplane or spaceship instruments, the control or operatio n of dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and other applications intended to support or sustain life. All Insecure Usage shall be made at customer’s risk, and in the event t hat third parties lay claims to Nuvoton as a result of customer’s Insecure Usage, customer shall indemnify the damages and liabilities thus incurred by Nuvoton.