MK3754 ICST | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

Low Cost 54 MHz 3.3 Volt VCXO Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com ICR OCLOC K Block Diagram Description Features The MK3754 is ICS/Microclock’s lowest cost, low jitter, high performance 3.3 Volt VCXO and PLL clock synthesizer designed to replace expensive 54 MHz VCXOs. The on-chip Voltage Controlled Crystal Oscillator accepts a 0 to 3.3 V input voltage to vary the output clocks by ±100 ppm. Using ICS/Microclock’s patented VCXO and analog/digital Phase-Locked Loop (PLL) techniques, the device uses an inexpensive external

13.5 MHz pullable crystal input to produce a

54 MHz output clock. The MK3754A is a drop-in replacement to the earlier MK3754S.

  • Packaged in 8 pin SOIC
  • 3.3 V only operating voltage
  • Uses an inexpensive 13.500 MHz external crystal
  • On-chip VCXO (patented) with pull range of 200ppm (minimum)
  • VCXO tuning voltage of 0 to 3.3 V
  • 12mA output drive capability at TTL levels
  • Advanced, low power, sub-micron CMOS process
  • The A version is the latest, manufactured in a smaller geometry process. The MK3754A gives a wider pull range than the MK3754S, and so is recommended for all new designs, and cost reductions of existing designs. Voltage Controlled Crystal Oscillator PLL/Clock Synthesis Circuitry

13.5 MHz

Low Cost 54 MHz 3.3 Volt VCXO Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com ICR OCLOC K Pin Descriptions Pin Assignment Number Name Description 1 X1 Crystal connection. Connect to a pullable 13.5 MHz crystal. 2 VDD VDD. Connect to +3.3 V. 3 VIN Voltage input to VCXO. Zero to 3.3V analog input which controls the frequency of the VCXO. 4 GND Connect to ground. 5 VDD VDD. Connect to +3.3 V. 6 CLK 54 MHz clock output. 7 GND Connect to ground. 8 X2 Crystal connection. Connect to a pullable 13.5 MHz crystal. 8 pin (150 mil) SOIC MK3754 1 8 X2X1 GND VDD CLKVIN GND VDD Pullable Crystal Specifications: Correlation (load) Capacitance 14 pF C0/C1 240 max ESR 35 Ω max Operating Temperature 0 to 70 °C Initial Accuracy ±20 ppm Temperature plus Aging Stability ±50 ppm

Low Cost 54 MHz 3.3 Volt VCXO Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com ICR OCLOC K Parameter Conditions Minimum Typical Maximum Units ABSOLUTE MAXIMUM RATINGS (note 1) ABSOLUTE MAXIMUM RATINGS (note 1) Supply voltage, VDD Referenced to GND 7 V Inputs and Clock Outputs Referenced to GND -0.5 VDD+0.5 V Ambient Operating Temperature 0 70 °C Soldering Temperature Max of 10 seconds 260 °C Storage temperature -65 150 °C DC CHARACTERISTICS (VDD = 3.3 V unless noted)DC CHARACTERISTICS (VDD = 3.3 V unless noted) Operating Voltage, VDD 3.15 3.45 V Output High Voltage, VOH IOH=-12mA 2.4 V Output Low Voltage, VOL IOL=12mA 0.4 V Output High Voltage, VOH, CMOS level IOH=-4mA VDD-0.4 V Operating Supply Current, IDD No Load 9 mA Short Circuit Current ±50 mA VIN, VCXO control voltage 0 3.3 V AC CHARACTERISTICS (VDD = 3.3 V unless noted)AC CHARACTERISTICS (VDD = 3.3 V unless noted) Input Crystal Frequency 13.50000 MHz Output Clock Rise Time 0.8 to 2.0V 1.5 ns Output Clock Fall Time 2.0 to 0.8V 1.5 ns Output Clock Duty Cycle At 1.4V 40 50 60 % Maximum Absolute Jitter, short term 100 ps 54 MHz output pullability, note 2 0V ≤ VIN ≤ 3.3 V ±100 ppm Electrical Specifications Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability. 2. With an ICS approved pullable crystal. The A version has a typical range of ±180 ppm. External Components The MK3754 requires a minimum number of external components for proper operation. A decoupling capacitor of 0.01µF should be connected between VDD and GND on pins 2 and 4, as close to the MK3754 as possible. A series termination resistor of 33 Ω may be used for the clock output. The input crystal must be connected as close to the chip as possible. The input crystal should be a parallel mode, pullable, AT cut, 13.5 MHz, with 14 pF load capacitance. Consult ICS for recommended suppliers. IMPORTANT - read application note MAN05 before laying out the PCB.

Low Cost 54 MHz 3.3 Volt VCXO Integrated Circuit Systems, Inc. • 525 Race Street • San Jose •CA•95126• (408) 295-9800 tel • www.icst.com ICR OCLOC K While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems Incorporated (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments.

Ordering Information

Part/Order Number Marking Shipping packaging Package Temperature MK3754A MK3754A tubes 8 pin SOIC 0-70 °C MK3754ATR MK3754A tape and reel 8 pin SOIC 0-70 °C MK3754S MK3754S tubes 8 pin SOIC 0-70 °C MK3754STR MK3754S tape and reel 8 pin SOIC 0-70 °C CHANGE HISTORY Version Date first published Status Comments D 6/01/00 Added A version C 12/29/99 Preliminary Added JEDEC dimensions. Changed VDD to ±5%. Added crystal specs. B 5/25/99 Preliminary Updated specs for crystal capacitance, IDD, jitter. A 4/19/99 Preliminary Original Package Outline and Package Dimensions (For current dimensional specifications, see JEDEC Publication No. 95.) B D E H e A1 C A h x 45° L INDEX AREA 1 2 8 pin SOIC Inches Inches Millimeters Millimeters Symbol Min Max Min Max A 0.0532 0.0688 1.35 1.75 A1 0.0040 0.0098 0.10 0.24 B 0.0130 0.0200 0.33 0.51 C 0.0075 0.0098 0.19 0.24 D 0.1890 0.1968 4.80 5.00 E 0.1497 0.1574 3.80 4.00 e .050 BSC .050 BSC 1.27 BSC 1.27 BSC H 0.2284 0.2440 5.80 6.20 h 0.0099 0.0195 0.25 0.50 L 0.0160 0.0500 0.41 1.27