MK3727 ICST | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

  • MK3727D and MK3727C are drop-in upgrades to the earlier MK3727S and MK3727A devices
  • MK3727D and MK3727C offer 24-36 MHz output frequency range (output frequency = 2x crystal frequency) and improved power supply noise rejection
  • Uses an inexpensive 12 to 18 MHz external crystal
  • Ideal for ADSL applications using 17.664 MHz external pullable crystal to generate locked 35.328 MHz clock physical layer clock
  • Ideal for set-top box applications using 13.5 MHz external pullable crystal to generate lock 27 MHz clock transport video clock
  • On-chip VCXO with guaranteed pull range of ±115 ppm minimum (MK3727D)
  • VCXO input tuning voltage 0 to 3.3 V
  • Packaged in 8 pin SOIC (150 mil wide) MK3727D is Recommended for New Designs. Block Diagram 24-36 MHz (2x Crystal Frequency) Voltage Controlled Crystal Oscillator PLL Frequency Doubler VIN 12-18 MHz Pullable Crystal

LOW COST 24 - 36 MHZ 3.3 VOLT VCXO Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3727 Pin Assignment Pin Descriptions VDD VIN GND GND NC CLK X21 MK3727S MK3727A MK3727C MK3727D

8 Pin (150 mil) SOIC

1 XI Input Crystal connection -- Connect to the external pullable crystal. 2 VDD Power Connect to +3.3 V (0.01uf decoupling capacitor recommended) 3 VIN Input Voltage input to VCXO -- 0 to 3.3 V analog input which controls the oscillation frequency of the VCXO.

4 GND Power Connect to ground

5 CLK Output Clock output

6 NC -- No internal connection (may connect to ground or VDD)

7 GND Power Connect to ground

8 X2 Input Crystal connection -- Connect to the external pullable crystal.

LOW COST 24 - 36 MHZ 3.3 VOLT VCXO Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3727 External Component Selection The MK3727 requires a minimum number of external components for proper operation. Decoupling Capacitor A decoupling capacitor of 0.01µF must be connected between VDD (pin 2) and GND (pin 4), as close to these pins as possible. For optimum device performance, the decoupling capacitor should be mounted on the component side of the PCB. Avoid the use of vias in the decoupling circuit. Series Termination Resistor When the PCB trace between the clock output (CLK, pin 5) and the load is over 1 inch, series termination should be used. To series terminate a 50Ω trace (a commonly used trace impedance) place a 33Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20Ω . Quartz Crystal The MK3727 VCXO function consists of the external crystal and the integrated VCXO oscillator circuit. To assure the best system performance (frequency pull range) and reliability, a crystal device with the recommended parameters (shown below) must be used, and the layout guidelines discussed in the following section shown must be followed. The frequency of oscillation of a quartz crystal is determined by its “cut” and by the load capacitors connected to it. The MK3727 incorporates on-chip variable load capacitors that “pull” (change) the frequency of the crystal. The crystal specified for use with the MK3727 is designed to have zero frequency error when the total of on-chip + stray capacitance is 14pF. Recommended Crystal Parameters: Initial Accuracy at 25 °C± 2 0 p p m Temperature Stability ±30 ppm Aging ±20 ppm Load Capacitance 14 pf Shunt Capacitance, C0 7 pF Max C0/C1 Ratio 250 Max Equivalent Series Resistance 35 Ω Max The external crystal must be connected as close to the chip as possible and should be on the same side of the PCB as the MK3727. There should be no via’s between the crystal pins and the X1 and X2 device pins. There should be no signal traces underneath or close to the crystal. Crystal Tuning Load Capacitors The crystal traces should include pads for small fixed capacitors, one between X1 and ground, and another between X2 and ground. Stuffing of these capacitors on the PCB is optional. The need for these capacitors is determined at system prototype evaluation, and is influenced by the particular crystal used (manufacture and frequency) and by PCB layout. The typical required capacitor value is 1 to 4 pF. To determine the need for and value of the crystal adjustment capacitors, you will need a PC board of your final layout, a frequency counter capable of about 1 ppm resolution and accuracy, two power supplies, and some samples of the crystals which you plan to use in production, along with measured initial accuracy for each crystal at the specified crystal load capacitance, CL. To determine the value of the crystal capacitors: 1. Connect VDD of the MK3727 to 3.3V. Connect pin 3 of the MK3727 to the second power supply. Adjust the voltage on pin 3 to 0V. Measure and record the frequency of the CLK output. 2. Adjust the voltage on pin 3 to 3.3V. Measure and record the frequency of the same output. To calculate the centering error: Where: f target = nominal crystal frequency errorxtal =actual initial accuracy (in ppm) of the crystal being measured If the centering error is less than ±25 ppm, no adjustment is needed. If the centering error is more than 25ppm negative, the PC board has excessive stray capacitance and a new PCB layout should be Error 10 6x f3.0V fte targ–() f0V fte targ–()+ fte targ

LOW COST 24 - 36 MHZ 3.3 VOLT VCXO Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3727 considered to reduce stray capacitance. (Alternately, the crystal may be re-specified to a higher load capacitance. Contact ICS MicroClock for details.) If the centering error is more than 25ppm positive, add identical fixed centering capacitors from each crystal pin to ground. The value for each of these caps (in pF) is given by: External Capacitor = 2 x (centering error)/(trim sensitivity) Trim sensitivity is a parameter which can be supplied by your crystal vendor. If you do not know the value, assume it is 30 ppm/pF. After any changes, repeat the measurement to verify that the remaining error is acceptably low (typically less than ±25ppm). Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the MK3727. These ratings, which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Recommended Operation Conditions Item Rating Supply Voltage, VDD 7V All Inputs and Outputs -0.5V to VDD+0.5V Ambient Operating Temperature 0 to +70 °C Storage Temperature -65 to +150 °C Soldering Temperature 260 °C Parameter Min. Typ. Max. Units Ambient Operating Temperature 0 – +70 °C Power Supply Voltage (measured in respect to GND) +3.15 +3.45 V Reference crystal parameters Refer to page 3

LOW COST 24 - 36 MHZ 3.3 VOLT VCXO Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3727 VDD=3.3V ±5% , Ambient temperature 0 to +70°C, unless stated otherwise VDD = 3.3V ±5%, Ambient Temperature 0 to +70° C, unless stated otherwise Note 1: External crystal device must conform with Pullable Crystal Specifications listed on page 3. Parameter Symbol Conditions Min. Typ. Max. Units Operating Voltage VDD 3.15 3.45 V Output High Voltage V OH IOH = -12 mA 2.4 V Output Low Voltage V OL IOL = 12 mA 0.4 V Output High Voltage (CMOS Level) VOH IOH = -4 mA VDD-0.4 V Operating Supply Current IDD Output = 27 MHz, no load 10 mA Short Circuit Current I OS ±50 mA VIN, VCXO Control Voltage V IA 03 . 3 V Parameter Symbol Conditions Min. Typ. Max. Units Output Frequency MK3727D and MK3727C FO VCXO Crystal frequency = 1/2 Output 24 36 MHz MK3727A and MK3727S FO VCXO Crystal frequency =

13.5 MHz

27 MHz

FP 0V< VIN < 3.3V, Note 1 + 115 ppm MK3727A and MK3727S FP 0V< VIN < 3.3V, Note 1 + 100 ppm VCXO Gain MK3727D VIN = VDD/2 + 1V, Note 1 120 ppm/V MK3727C VIN = VDD/2 + 1V, Note 1 150 ppm/V MK3727A VIN = VDD/2 + 1V, Note 1 170 ppm/V MK3727S VIN = VDD/2 + 1V, Note 1 100 ppm/V Output Rise Time t OR 0.8 to 2.0V, CL=15pF 1.5 ns Output Fall Time t OF 2.0 to 0.8V, CL=15pF 1.5 ns Output Clock Duty Cycle t D Measured at 1.4V, CL=15pF 40 50 60 % Maximum Output Jitter, short term tJ C L=15pF 100 ps

LOW COST 24 - 36 MHZ 3.3 VOLT VCXO Integrated Circuit Systems ● 525 Race Street, San Jose, CA 95126 ● tel (408) 295-9800 ● www.icst.com MK3727 Package Outline and Package Dimensions (8 pin SOIC, 150 Mil. Narrow Body) Package dimensions are kept current with JEDEC Publication No. 95

Ordering Information

Note 1: MK3727D is recommended for new designs. While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems (ICS) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. Part / Order Number (Note 1) Marking Shipping packaging Package Temperature MK3727D MK3727D Tubes 8 pin SOIC 0 to +70 ° C MK3727DTR MK3727D Tape and Reel 8 pin SOIC 0 to +70 ° C MK3727C MK3727C Tubes 8 pin SOIC 0 to +70 ° C MK3727CTR MK3727C Tape and Reel 8 pin SOIC 0 to +70 ° C MK3727A MK3727A Tubes 8 pin SOIC 0 to +70 ° C MK3727ATR MK3727A Tape and Reel 8 pin SOIC 0 to +70 ° C MK3727S MK3727S Tubes 8 pin SOIC 0 to +70 ° C MK3727STR MK3727S Tape and Reel 8 pin SOIC 0 to +70 ° C D EH c h x 450 be Q A Pin 1 Index Area Millimeters Inches S y m b o l M i nM a xM i nM a x A 1.35 1.75 0.0532 0.0688 A1 1.10 0.25 0.0040 0.0098 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.0075 0.0098 D 4.80 5.00 .1890 .1968 E 3.80 4.00 0.1497 0.1574 e 1.27 Basic 0.050 Basic H 5.80 6.20 0.2284 0.2440 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 a0 ° 8° 0° 8°