MK1573-02 ICST | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

GenClock ™ HSYNC to Video Clock Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126•(408)295-9800tel•www.icst.com

  • Packaged in 16 pin narrow (150 mil) SOIC
  • The -02 version has one frequency changed (32MHz was added), and tracks the HSYNC better than the -01 version.
  • Exact ratios stored in the device eliminate the need for external dividers
  • Accepts HSYNC of 15.625kHz or 15.73426kHz
  • Highly accurate frequency generation within 1 ppm
  • Generates NTSC/PAL subcarrier frequencies, and 4X and 8X of those frequencies
  • Generates 27MHz and 13.5MHz
  • 2X HSYNC clock available
  • Recovered HSYNC clock available
  • Inverted HSYNC clock available
  • 4.5V to 5.5V operation The MK1573 GenClock™ provides genlock timing for video overlay systems. The device accepts the horizontal sync (HSYNC) signal as the input reference clock, and generates a frequency- locked high speed output. Stored in the device are the multipliers for 16 combinations of popular frequencies for analog and digital TV and set-top box systems. Frequency-locked outputs include 1X, 4X, and 8X the subcarrier frequencies of NTSC and PAL systems, and 27MHz plus 13.5MHz for digital video systems. In most selections, the chip recovers the HSYNC clock by outputting a low jitter 50% duty cycle version of HSYNC. Also available is an inverted recovered HSYNC clock, and a double speed recovered HSYNC clock. MicroClock can customize this device for any other different frequencies. Block Diagram Description Features Input Buffer VDD GND Clock Synthesis and Control Circuitry HSYNC Input Clock Output Buffer Output Buffer CLK1 2 2 Output Buffer CLK2 FS0-3 CLK3 OE (all outputs)

GenClock ™ HSYNC to Video Clock Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126•(408)295-9800tel•www.icst.com Number Name Type Description 1 HSYNC I HSYNC clock input. The output clocks are synchronized to the HSYNC falling edge. 2 VDD P Connect to +5V. 3 VDD P Connect to +5V. 4 CAP1 I Connect a 0.01µF ceramic capacitor and a 39kΩ resistor in series between this pin and CAP2. 5 GND P Connect to ground. 6 CAP2 I Connect a 0.01µF ceramic capacitor and a 39kΩ resistor in series between this pin and CAP1. 7 GND P Connect to ground. 8 FS0 I Frequency Select 0. Determines CLK outputs (with given input) per table above. 9 CLK3 O Clock 3 determined by status of FS3:0 per table above. 10 CLK1 O Clock 1 determined by status of FS3:0 per table above. 11 OE I Output Enable. Tri-states the three output clocks when low. 12 CLK2 O Clock 2 determined by status of FS3:0 per table above. 13 FS1 I Frequency Select 1. Determines CLK outputs (with given input) per table above. 14 FS2 I Frequency Select 2. Determines CLK outputs (with given input) per table above. 15 N/C - No Connect. Nothing is connected to this pin. 16 FS3 I Frequency Select 3. Determines CLK outputs (with given input) per table above. Pin Descriptions Type: I = Input, O = output, P = power supply connection Pin Assignment Output Clocks Decoding Table MK1573-02 (MHz) 16 pin (150 mil) SOIC 1 16 13CAP1 GND VDD FS1 OE 9FS0 FS2 CAP2 FS3 CLK2 CLK3 GND CLK1 VDD HSYNC N/C

  • 0 = connect directly to ground, 1 = connect directly to VDD.
  • CLK2 is a recovered HSYNC (with 50% duty cycle) on selections in italic.
  • HSYNC reference outputs on CLK3 (in italic) are inverted, recovered HSYNC. Decode Address HSYNC Multiplier CLK 1 CLK 2 CLK 3 FS3:0 (Hex) pin 1 On-chip pin 10 pin 12 pin 9 0 15.625k 1536 24M 12M 15.625k 1 15.734264k 1525 1/3 24M 12M 15.734264k 2 15.625k 1728 27M 13.5M 15.625k 3 15.734264k 1716 27M 13.5M 15.734264k 4 15.625k 960 15M 7.5M 15.625k 5 15.734264k 953 1/3 15M 7.5M 15.734264k 6 15.625k 3840 60M 30M 15.625k 7 15.734264k 3840 60.41957M 30.20979M 15.734264k 8 15.625k 2270 35.46875M 17.734375M 4.433594M 9 15.734264k 1820 28.63636M 14.31818M 3.579545M A 15.625k 2270 35.46875M 15.625k 15.625k B 15.734264k 1820 28.63636M 15.734264k 15.734264k C 15.625k 2048 32M 16M 15.625k D 15.734264k 808 12.71329M 15.734264k 31.4685k E 15.625k 2270 35.46875M 15.625k 31.25k F 15.734264k 1820 28.63636M 15.734264k 31.4685k 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111

GenClock ™ HSYNC to Video Clock Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126•(408)295-9800tel•www.icst.com Parameter Conditions Minimum Typical Maximum Units ABSOLUTE MAXIMUM RATINGS (Note 1) ABSOLUTE MAXIMUM RATINGS (Note 1) Supply Voltage, VDD Referenced to GND 7 V Inputs and Clock Outputs -0.5 VDD+0.5 V Ambient Operating Temperature 0 70 °C Soldering Temperature Max of 10 seconds 250 °C Storage Temperature -65 150 °C DC CHARACTERISTICS (VDD = 5V unless noted)DC CHARACTERISTICS (VDD = 5V unless noted) Operating Voltage, VDD 4.5 5.5 V Input High Voltage, VIH 2 V Input Low Voltage, VIL 0.8 V Output High Voltage IOH=-4mA VDD-0.4 V Output High Voltage IOH=-25mA 2.4 V Output Low Voltage IOL=25mA 0.4 V Operating Supply Current, IDD No Load, VDD=5.0V 15 mA Short Circuit Current Each output ±100 mA Input Capacitance 7 pF Actual mean frequency error versus target, note 2 Any clock selection 0 1 ppm AC CHARACTERISTICS (VDD = 5V unless noted)AC CHARACTERISTICS (VDD = 5V unless noted) Input Frequency, NTSC 15.734264 kHz Input Frequency, PAL 15.625 kHz Output Clock Rise Time 0.8 to 2.0V 1.5 ns Output Clock Fall Time 2.0 to 0.8V 1.5 ns Output Clock Duty Cycle, High Time At VDD/2 40 49 to 51 60 % Absolute Clock Period Jitter TBD ps Output Enable Time, OE high to outputs on 50 ns Output Disable Time, OE low to tri-state 3 µs Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability. 2. Most selections have zero ppm error. Some selections have a maximum of 1 ppm synthesis error . External Components/Crystal Selection Electrical Specifications The MK1573 requires a minimum number of external components for proper operation. A 0.1µF low leakage capacitor (see Capacitor Selection on following page) should be connected between CAP1 and CAP2 as close to the chip as possible. A high quality ceramic capacitor is recommended. A decoupling capacitor of 0.1µF must be connected between VDD and GND pins (pins 2 and 3, 5 and 7) close to the chip, and 33Ω terminating resistors can be used on clock outputs with traces longer than 1 inch.

GenClock ™ HSYNC to Video Clock Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126•(408)295-9800tel•www.icst.com The series connected capacitor and resistor between CAP1 and CAP2 (pins 4 and 6) determine the dynamic characteristics of the phase-locked loop. The capacitor must have very low leakage, therefor a high quality ceramic capacitor is recommended. DO NOT use any type of polarized or electrolytic capacitor. The values of the RC network determine the bandwidth of the PLL. The tracking of the jitter on the HSYNC input improves with increasing values of R and decreasing values of C, until a point is reached where the loop starts becoming unstable. At that point, HSYNC tracking becomes unreliable. Loop filter values between 470pF and 0.01µF, and 18k Ω and 120kΩ will work for most application where the PLL must track HSYNC jitter with minimum error. A good starting point is 680pF and 82kΩ . The optimum values should be determined by the spectral characteristics of the HSYNC jitter. The following formula gives the approximate loop bandwidth for the MK1573: where: fbw is the loop bandwidth in Hertz fclk1 is the frequency of CLK1 in Hertz C is the value of capacitor in Farads For example, if CLK1 is running at 24MHz and C=1000pF, then fbw = fclk1 • C 537 fbw = 537 24x106 • 1x10 -9 = 3.47kHz Loop Bandwidth and Loop Filter Component Selection Video Clock Multipliers/Accuracies In the table on page 2 are the actual multipliers stored in the MK1573-02 ROM, which shows that the accuracies are within one ppm for the output clocks. PC Board Layout A proper board layout is critical to the successful use of the MK1573. In particular, the CAP1 and CAP2 pins are very sensitive to noise and leakage (CAP1 at pin 4 is the most sensitive). Traces must be as short as possible and the capacitor and resistor must be mounted next to the device as shown to the right. The capacitor connected between pins 3 and 5 is the power supply decoupling capacitor. The high frequency output clocks on CLK1 and CLK2 may benefit from a series 33 Ω resistor connected close to the pin (not shown). G V =connect to VDD =connect to GND V G cap If minimum absolute jitter is required, the RC network should be replaced by a single capacitor with a value between 0.01µF and 2µF. Larger values will cause the PLL to start more slowly. For example, if C=2µF, the loop may take several seconds to start. cap resist.

GenClock ™ HSYNC to Video Clock Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126•(408)295-9800tel•www.icst.com Clock Waveforms In addition to generating the video clock on CLK1 (pin 10), the MK1573 also outputs the recovered HSYNC clocks. On certain selections, a double speed recovered HSYNC clock is also available. These recovered clocks will have lower jitter than the HSYNC input due to the filtering action of the PLL. The jitter spectrum of the recovered clocks will be reduced at frequencies higher than the loop bandwidth. The above section describes how to calculate the approximate loop bandwidth. The waveforms of the recovered clocks fall into one of three different groups depending on the address selection: HSYNC input CLK3 Addresses 0 to 7 and C HSYNC input CLK3 Addresses D, E, and F CLK2 The recovered clocks are triggered by the falling edge of HSYNC and are delayed by about 100ns. HSYNC input CLK3 Addresses A and B CLK2

GenClock ™ HSYNC to Video Clock Integrated Circuit Systems, Inc. • 525 Race Street • San Jose • CA • 95126•(408)295-9800tel•www.icst.com b D E H e Q c A h x 45° Package Outline and Package Dimensions

Ordering Information

Inches Inches Millimeters Millimeters Symbol Min Max Min Max A 0.055 0.070 1.397 1.778 b 0.013 0.019 0.330 0.483 c 0.007 0.010 0.191 0.254 D 0.385 0.400 9.779 10.160 E 0.150 0.160 3.810 4.064 H 0.225 0.245 5.715 6.223 e .050 BSC .050 BSC 1.27 BSC 1.27 BSC h 0.016 0.406 Q 0.004 0.01 0.102 0.254 While the information presented herein has been checked for both accuracy and reliability, MicroClock Incorporated assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by MicroClock. MicroClock reserves the right to change any circuitry or specifications without notice. MicroClock does not authorize or warrant any MicroClock product for use in life support devices or critical medical instruments. Part/Order Number Marking Package Temperature MK1573-02S MK1573-02S 16 pin narrow SOIC 0-70°C MK1573-02STR MK1573-02S Add Tape & Reel 0-70°C CHANGE HISTORY Version Date first published Comments A 10/18/96 Original B 12/4/97 Final version GenClock is a trademark of MicroClock Incorporated ©1996 MicroClock Incorporated