MFS4R12CB-005-C | DigiCamel IC Datasheet

Online Datasheet

Read MFS4R12CB-005-C online.

MFS4R12CB-005-C ATGBICS

Document overview

Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
PDF pages: 9

Technical content

FEATURES

QSFP MSA compliant
Four-channel full-duplex active optical cable
Transmission data rate up to 11.3Gbit/s per channel
Reliable VCSEL array technology using multimode fiber
Available in standard lengths of 3, 5, 10, 15, 20, 30, 50,100m
Low power consumption <1.5W
Operating case temperature 0°C to +70°C
3.3V power supply voltage
RoHS 6 compliant
Hot Pluggable QSFP form factor

APPLICATIONS

Infiniband QDR/DDR/SDR
Datacenter
40G Ethernet
4G/8G/10G Fibre Channel

DESCRIPTION

ATGBICS MFS4R12CB-005-C QSFP+ active optical cables are a high performance, low power consumption, long reach interconnect solution supporting InfiniBand QDR/DDR/SDR, 12.5G/10G/8G/4G/2G fiber channel, PCIe and SAS. It is compliant with the QSFP MSA and IEEE P802.3ba. WAREX QSFP AOC is an assembly of 4 full-duplex lanes, where each lane is capable of transmitting data at rates up to 11.3Gb/s, providing an aggregated rate of 45.2Gb/s. WAREX QSFP+ AOC is one kind of parallel transceiver which provides increased port density and total system cost savings.

ATGBICS® All rights reserved. EOE Ref: ATGBICS_MFS4R12CB-005-C_V1 Page 2 of 9 Product Datasheet Absolute Maximum Ratings Parameter Symbol Min Max Unit Storage Temperature TST -40 85 degC Relative Humidity(non-condensing) RH 0 85 % Operating Case Temperature TOPC 0 70 degC Supply Voltage VCC -0.3 3.6 V Input Voltage Vin -0.3 Vcc+0.3 V Note: 1. The operation in excess of any absolute maximum ratings might cause permanent damage to this module Recommended Operating Conditions and Supply Requirements Parameter Symbol Min Typical Max Unit Operating Case Temperature TOPC 0 70 degC Power Supply Voltage VCC 3.13 3.3 3.47 V Power Consumption - 1.5 W Data Rate DR 1 10.3 11.3 Gbps Data Speed Tolerance ∆DR -100 +100 ppm Link Distance with OM3 fiber D 0 100 m

ATGBICS® All rights reserved. EOE Ref: ATGBICS_MFS4R12CB-005-C_V1 Page 3 of 9 Product Datasheet Electrical Specifications Parameter Symbol Min Typical Max Unit Differential input impedance Zin 90 100 110 ohm Differential Output impedance Zout 90 100 110 ohm Differential input voltage amplitude ΔVin 300 1100 mVp-p Differential output voltage amplitude ΔVout 500 800 mVp-p Bit Error Rate BR E-12 Input Logic Level High VIH 2.0 VCC V Input Logic Level Low VIL 0 0.8 V Output Logic Level High VOH VCC-0.5 VCC V Output Logic Level Low VOL 0 0.4 V

1 GND Ground 1

2 CML-I Tx2n Transmitter Inverted Data Input

3 CML-I Tx2p Transmitter Non-Inverted Data output

4 GND Ground 1

5 CML-I Tx4n Transmitter Inverted Data Input

6 CML-I Tx4p Transmitter Non-Inverted Data output

7 GND Ground 1

8 LVTLL-I ModSelL Module Select

9 LVTLL-I ResetL Module Reset

10 VccRx ﹢3.3V Power Supply Receiver 2

11 LVCMOS-I/O SCL 2-Wire Serial Interface Clock

12 LVCMOS-I/O SDA 2-Wire Serial Interface Data

13 GND Ground

14 CML-O Rx3p Receiver Non-Inverted Data Output

15 CML-O Rx3n Receiver Inverted Data Output

16 GND Ground 1

17 CML-O Rx1p Receiver Non-Inverted Data Output

18 CML-O Rx1n Receiver Inverted Data Output

19 GND Ground 1

20 GND Ground 1

21 CML-O Rx2n Receiver Inverted Data Output

22 CML-O Rx2p Receiver Non-Inverted Data Output

23 GND Ground 1

24 CML-O Rx4n Receiver Inverted Data Output 1

25 CML-O Rx4p Receiver Non-Inverted Data Output

26 GND Ground 1

27 LVTTL-O ModPrsL Module Present

28 LVTTL-O IntL Interrupt

29 VccTx +3.3 V Power Supply transmitter 2 30 Vcc1 +3.3 V Power Supply 2

31 LVTTL-I LPMode Low Power Mode

32 GND Ground 1

33 CML-I Tx3p Transmitter Non-Inverted Data Input

34 CML-I Tx3n Transmitter Inverted Data Output

35 GND Ground 1

36 CML-I Tx1p Transmitter Non-Inverted Data Input

37 CML-I Tx1n Transmitter Inverted Data Output

38 GND Ground 1

Notes: 1. Module circuit ground is isolated from module chassis ground within the module. GND is the symbol for signal and supply (power) common for QSFP modules 2. The connector pins are each rated for a maximum current of 500mA

ATGBICS® All rights reserved. EOE Ref: ATGBICS_MFS4R12CB-005-C_V1 Page 6 of 9 Product Datasheet Power Supply Filtering The host board should use the power supply filtering shown in Figure1 Figure1. Host Board Power Supply Filtering

ATGBICS® All rights reserved. EOE Ref: ATGBICS_MFS4R12CB-005-C_V1 Page 7 of 9 Product Datasheet EEPROM Serial ID Memory Contents: Serial ID: Data Fields (Page 00) Address Size (Bytes) Name Description of Base ID Field Optical Module 128 1 Identifier Identifier Type of serial Module R 129 1 Ext. Identifier Extended Identifier of Serial Module R 130 1 Connector Code for connector type R 131-138 8 Specification compliance Code for electronic compatibility or optical compatibility R 139 1 Encoding Code for serial encoding algorithm R 140 1 BR, nominal Nominal bit rate, units of 100 MBits/s R 141 1 Extended rate select Compliance Tags for extended rate select compliance R 142 1 Length (SMF) Link length supported for SMF fiber in km (note 1) R 143 1 Length (OM3 50um) Link length supported for EBW 50/125 um fiber (OM3), units of 2m (note 1) R 144 1 Length (OM2 50um) Link length supported for 50/125 um fiber (OM2), units of 1m (note 1) R 145 1 Length (OM1 62.5um) Link length supported for 62.5/125 um fiber (OM1), units of 1m (note 1) R 146 1 Length (Copper) Link length of copper or active cable, units of 1m (note 1) Link length supported for 50/125 um fiber (OM4), units of 2 m) when Byte 147 declares 850 nm VCSEL as defined in Table 37 R 147 1 Device tech Device technology R 148-163 16 Vendor name QSFP+ vendor name (ASCII) R 164 1 Extended Module Extended Module codes for InfiniBand R 165-167 3 Vendor OUI QSFP+ vendor IEEE company ID R 168-183 16 Vendor PN Part number provided by QSFP+ vendor (ASCII) R

ATGBICS® All rights reserved. EOE Ref: ATGBICS_MFS4R12CB-005-C_V1 Page 8 of 9 Product Datasheet 184-185 2 Vendor rev Revision level for part number provided by vendor (ASCII) R 186-187 2 Wavelength or Copper cable Attenuation Nominal laser wavelength (wavelength=value/20 in nm) or copper cable attenuation in dB at 2.5GHz (Adrs 186) and 5.0GHz (Adrs 187) R 188-189 2 Wavelength tolerance Guaranteed range of laser wavelength (+/- value) from nominal wavelength. (Wavelength Tol. = value/200 in nm) R 190 1 Max case temp. Maximum case temperature in degrees C R 191 1 CC_BASE Check code for base ID fields (addresses 128-190) R 192-195 4 Options Rate Select, TX Disable, TX Fault, LOS, Warning indicators for: Temperature, VCC, RX power, TX Bias R 196-211 16 Vendor SN Serial number provided by vendor (ASCII) R 212-219 8 Date Code Vendor’s manufacturing date code R 220 1 Diagnostic Monitoring Type Indicates which types of diagnostic monitoring are implemented (if any) in the Module. Bit 1,0 Reserved R 221 1 Enhanced Options Indicates which optional enhanced features are implemented in the Module. R 222

1 Reserved

223 1 CC_EXT Check code for the Extended ID Fields (addresses 192-222) R Vendor Specific ID Fields 224-255 32 Vendor Specific EEPROM

Ordering Information

Product Information

MFS4R12CB-005-C specifications and overview.

Summary

MFS4R12CB-005 NVIDIA Mellanox Compatible Active Optical Cable 40G QSFP+ (5m)

Description

MFS4R12CB-005 NVIDIA Mellanox Compatible Active Optical Cable 40G QSFP+ (5m)

Source title MFS4R12CB-005-C Datasheet(PDF) - ATGBICS by Approved Technology

Related Parts

More parts from the same family.

Browse manufacturer