4003542 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 8
Technical content
MODEL NO: MFL800R PART NO: 4003542
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Worklight. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. TECHNICAL SPECIFICATIONS GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for its intended purpose. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. Model MFL800R Operating voltages 3.7V ( light), / 230V (charger) LED Wattage consumption 9W(max) LED replaceable No Rechargable Lithium battery 3.7V / 4400mAh LED Light source 4 x 1W SMD, 1 x 5W LED, 1 x 2W LED Light output (luminous flux) max 800 Lm Colour temperature (rendering) 6000 - 6800K Ingress Protection (IP rating) IP20 Battery charging time 6 hours Approximate Run Time 5 Hours Efficiency 88 Lm/W Operating temperatures 0 to +45 oC Dimension 55 x 255 x 42mm Weight 330g
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SAFETY INSTRUCTIONS 1. ALWA YS check for damage before using the worklight. Inspect the power cable and plug for damage. Any damage should be properly repaired or the part replaced. Consult your local CLARKE dealer. 2. ALWA YS ensure that the voltage marked on the charger matches the power supply to be used. 3. NEVER use this lamp in a bathroom or in the vicinity of a swimming pool. 4. NEVER cover the lamp. 5. NEVER pull the cable to remove the charger plug from the power supply. 6. DO NOT look directly into the worklight when it is switched on. 7. Keep the worklight out of the reach of children. 8. Charge the worklight in a dry indoor location. DO NOT immerse in water or any other liquid. 9. ALWA YS fully charge before first use. 10. DO NOT turn on the light when charging. 11. DO NOT leave the worklight on charge for more than 24 hours. 12. DO NOT disassemble the worklight as there are no user changeable parts. 13. This worklight utilises a rechargeable Lithium-ion battery that can rupture, ignite and cause serious injury if being used improperly. 14. DO NOT put batteries and the worklight in the fire or high temperature. 15. DO NOT puncture or damage the batteries. 16. DO NOT immerse or expose the worklight to water. 17. DO NOT dispose of the worklight in a fire or water. THE FOLLOWING WARNING SYMBOLS ARE FOUND ON THE PRODUCT Indoor use Harmful to aquatic life Pacemaker hazard (due to magnet) Not suitable for use by children
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ENVIRONMENTAL RECYCLING POLICY Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE. In effect, this means that this product must not be disposed of with general household waste but according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility. The light source contained in this worklight has a life expectancy of approximately 50000 hours after which the worklight should be disposed of in an environmentally responsible way. The Lithium Ion battery falls under the Waste Batteries and Accumulators Regulations 2009 and should be disposed of in a controlled manner. BATTERY CHARGING 1. Connect the AC charging adaptor to the charging jack on the worklight. 2. Connect the other end of the charger to the 230V mains power supply and charge until fully charged.
- The battery condition indicator will illuminate when charging. The worklight should not be used while using the charger. 3. The battery should be re-charged at least every 3 months. Failure to re-charge the battery will lead to reduced performance of the worklight and to premature battery failure. 4. If you plan to store the worklight (e.g. for emergencies), we recommend that the battery is fully charged before doing so. This will ensure the longest possible battery life. 5. NEVER abuse the charger cable or yank the cable to disconnect it. Keep the cable away from sharp edges/hot surfaces.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OPERATION To switch on the different LEDs, press the ON/ OFF button in the following sequence. 1. The first press switches on the centre light. 2. The second press switches on the two upper and two lower LEDs. 3. The third press switches on all LEDs. 4. The fourth press makes all lights brighter. 5. The fourth press switches off the main lights and switches on the end LED (torch) light. 6. The fifth press switches the unit off. NOTE: If set to 3 or 4 for longer than a few seconds, the next press switches the unit off. CAUTION: NEVER SHINE ANY LED LIGHT DIRECTLY INTO ANYONE’S EYES. Attach the worklight to a suitable support using the folding hook or attach to a ferrous metal surface using the magnetic retainer. Angle the worklight to suit the task by bending and/or twisting the top half of the unit to shine in any direction. To keep your worklight clean, wipe with a damp cloth only, DO NOT use detergents, chemicals or harmful abrasives. Never immerse in water.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com COMPONENT PARTS Item Description Item Description Item Description
1 Front Lens 10 Switch Support 19 Lithium Battery
2 Housing 11 Switch Cap 20 Ratchet
3 Reflector 12 Radiator 21 Back Pivot
4 LED Plate 13 Back Housing 22 Hook Support
5 Torch LED 14 Sticker 23 Back Housing
6 LED Lens 15 DC Hole Rubber 24 Hook
7 DC Socket Nut 16 Front Pivot 25 Screw
8 DC Socket 17 Front Housing 26 Magnet
9 PCBA 18 Fluorescent Ring 27 Magnet Support
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATIONS OF CONFORMITY