MCCB400-3PNL-MC

EDS1207-001 EUROPA | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 8

Technical content

It is the responsibility of the person installing the electrical equipment to ensure that the installation meets the requirements of the IET wiring regulations and is therefore ‘fit for purpose’. Factors such as correct selection of components, cable sizing, protective devices and Earth bonding are all critical and should be checked prior to full testing and power-up. Any other regulations applicable to the equipment being installed such as the Machinery Directive and current health and safety legislation must also be adhered to. All connections (including factory made) must be checked for the correct tightness prior to commissioning of the electrical installation. All connections should be checked periodically to ensure correct tightness. DO NOT USE POWER TOOLS ON THESE PRODUCTS Technical Data: MCCB400 (S400-CJ) IP4X Enclosed MCCBs 500 6 x HOLES 8.5 DIA TOP AND BOTTOM GLAND PLATES 2mm THICK 102 103 NOTE: TERMINAL SHROUDS NOT SHOWN FOR CLARITY 165 197 120 M10 BOLT 14-22Nm 340 386 MAXIMUM CABLE SIZE 2 x 240mm sq.

400 FIXING CENTRES

900 FIXING CENTRES

6Nm Max. WARNING: All connections (including factory made) must be checked for the correct tightness prior to the commissioning of the electrical installation MCCB400-3PNL-MC

EDS1207-001Europa House, Airport Way, Luton, Beds, LU2 9NH Tel: 01582 692 440 / Fax: 01582 692 450 e-mail: sales@europacomponents.com / website: http://www.europacomponents.com Technical Data: MCCB400 (S400-CJ) IP4X Enclosed MCCBs 500 6 x HOLES 8.5 DIA TOP AND BOTTOM GLAND PLATES 2mm THICK 102 103 NOTE: TERMINAL SHROUDS NOT SHOWN FOR CLARITY 165 197 340 M12 BOLT 40 - 65Nm 180 60 60 MAXIMUM CABLE SIZE 2 x 240mm sq. 7,5 WARNING: All connections (including factory made) must be checked for the correct tightness prior to the commissioning of the electrical installation

4,500 15,000 630Max In (A) of Frame Model S400 Number of Poles 3, 4 Type CJ Nominal current ratings In (A) 50°C 250 400

Electrical characteristics

Rated operational voltage U e (V) AC 50/60 Hz 690 250 800 DC Rated insulation voltage U i (V) Rated impulse withstand voltage Uimp (kV) Ultimate breaking capacity Icu (kA) 690V AC 15 (IEC, JIS, AS/NZS) 525V AC 440V AC 400/415V AC 220/240V AC 250V DC Service breaking capacity I cs (kA) 690V AC (IEC, JIS, AS/NZS) 525V AC 440V AC 400/415V AC 220/240V AC 250V DC Rated breaking capacity (NEMA) (kA) 480V AC 22 50240V AC Rated short-time withstand current Icw (kA) 0.3 Seconds - Protection Adjustable thermal, adjustable magnetic Fixed thermal, fixed magnetic Microprocessor Utilisation category A Installation Front connection (FC) Extension bar (FB) Cable clamp (FW)  Rear connection (RC) Plug-in (PM) DIN rail mounting (DA) - Dimensions height (mm) 260 140 185 103 4.3 5.6 width (mm) 3 pole (mm) 4 pole depth (mm) Weight weight (kg) 3 pole 4 pole Operation Direct Opening Action Toggle operation Door mounted (HS) / Breaker mounted handle (HB) Motor operation (MC)  Endurance Electrical cycles 415V AC Mechanical cycles DATA SHEET: TEMBREAK 2 S400-CJ MCCB Standard  Optional - Not Available TB2 E/S 630 Page 1 of 4

(optional) With extension bars (optional) Front connected Rear connected Front connected with Motor Operator Rear connected with Motor Operator DATA SHEET: TEMBREAK 2 S400-CJ MCCB Outline Dimensions S400-CJ ASL: Arrangement Standard Line HL: Handle Frame Centre Line Page 2 of 4

8 (max.) 20 (max.) Preperation of conductor 30 (max.) Support or rail Support or rail Mounting screw M10x30 max. Mounting screw M5 x 20 Mounting plate 102 260 102 113 138 142 180 198 258 276 102 260 204 208 246 Insulating plate Mounting plate Mounting M6 NUT Insulating plate Mounting screw M6x70 Mounting on a support or rails (shown with optional connection bars oriented for rear access) Mounting through the backplate (shown with optional connection bars oriented for rear access) Mounting on the backplate (optional connection bars must be oriented for front access) Outline Dimensions Termination of Busbar ASL: Arrangement Standard Line HL: Handle Frame Centre Line DATA SHEET: TEMBREAK 2 S400-CJ MCCB Outline Dimensions S400-CJ Plug-in Version Page 3 of 4

Innovators in Protection Technology Time/Current Characteristic Curve S400-CJ Page 4 of 4 DATA SHEET: TEMBREAK 2 S400-CJ MCCB

Shunt Trip Undervoltagie Trip ˎ ˎ ˎ ˎ ˎ ˎ Auxiliary Switch Innovators in Protection Technology 2G0789SAB(KRB-5336b) 7-2-10 Kamihigashi, Hiranoku, Osaka 547-0002, Japan TEL:81-6-6791-9323/ FAX:81-6-6791-9274 URLɿIUUQwww.terasaki.co.jp E-mailɿJOUTBMFT!UFSBTBLJDPKQ Instruction Manual for Moulded Case Circuit Breakers Types ɾAdjustable Thermal Magnetic Type E400-NJ S400-CJ S400-NJ S400-GJ S400-PJ ɾElectronic Type S400-NE S400-GE S400-PE c Operating Instructions v Fitting Internal Accessories ˎSymbols of Accessories Ring Mark RESET TRIPPED 2 2 3 ʢOFFʣ Slits of pulling out leads AX AL SH UV V 1 2 RemovalPull Out Leads on Load SideCombination ɾAfter fitting, verify the function of the Accessory. Handle Trip Button ʢONʣ ʢOFFʣ #5ZQF .5ZQF *ODBTFPGGJUUJOHPOF PSUXP BVYJMJBSZ TXJUDI GJUJOBOPSEFSGSPNBMFGUTJEF TMPU ʢONʣ ʢOFFʣ ʢONʣ ʢOFFʣ Auxiliary Switch Alarm Switch a contact b contact a contact b contact 11/AXc-14/AXa 11/AXc-12/AXb 91/ALc 94/ALa 91/ALc 92/ALb 21/AXc-24/AXa 21/AXc-22/AXb 31/AXc-34/AXa 31/AXc-32/AXb Shunt Trip power source C1-C2 Undervoltage Trip power source D1-D2 Please retain this manual for future reference.The Manufacturer assumes no responsibility for damages resulting from non-application or incorrect application of the instructions provided herein. z Safety Notices Be sure to read these Instructions and other associated documents accompanying the product thoroughly to be familiarize yourself with the product handling, safety information, and all other precautions before mounting, using, servicing, or inspecting the product. In these Instructions, safety notices are divided into "Warning" and "Caution" according to the hazard level: : A warning notice with this symbol indicates that neglecting the suggested procedure or practice could result in lethal or serious personal injury. : A caution notice with this symbol indicates that neglecting the suggested procedure or practice could result in moderate or slight personal injury and/or property damage. Note that failing to observe notices could result in serious results in some cases. Because safety notices contain important information, be sure to read and observe them. ˙Other Precautions ɾDo not carry this product by accessory leads, as this may cause damage to the product. ɾUnauthorised opening of the breaker cover will invalidate product warranty. ɾWhen installing the product, use wires or conductors, the cross sectional areas of which accommodate the rated current of the product. Using wires or conductors with inadequate cross sectional areas may cause false tripping and overheat. ˙Mounting Precautions (For detailed mounting dimensions, refer to the TemBreak2 catalogue.) ˔Electrical work should only be undertaken by suitably qualified persons. ˔Do not place the product in an area that is subject to high temperature, high humidity, excessive dusty air, corrosive gas, strong vibration and shock, or other unusual conditions. Mounting in such areas could cause a fire or malfunction. ˔Be careful to prevent foreign objects (debris, concrete powder, iron powder, etc.) and rainwater from entering product. These materials inside the product could cause a fire or malfunction. Prior to commencing any work on the product, open an upstream circuit breaker or isolator to ensure that no voltage is applied to the product. Otherwise, electrical shock may result. ˔For 4-pole breakers, be sure to connect a neutral conductor to the N pole. Otherwise, an over-current may hinder the product from tripping, thus resulting in a fire. ˔When connecting cable or busbar to the product, tighten terminal screws to the torque specified in this manual. Otherwise, a fire could result. ˔Even when tightening the terminal screws and after conductor connection, do not apply excessive force to the terminals. Otherwise, a fire may result. ˔For front-connected breakers, Insulate all bare conductors of the line side until the breaker end. If interpole barriers are packed, be sure to use the barriers; moreover, insulate all bare conductors by insulating tape or the like so that the tape overlaps with the barriers. Insufficient insulation may result in short- circuit. ˔Do not block the arc gas vents of the product to ensure adequate arc space. Blocking these vents could result in failure of circuit interruption. Caution ˙Handling Precautions ˔Never touch terminals. Otherwise, electric shock may result. Warning ˔When the breaker trips open automatically, remove the cause, then return the handle to the | (ON) position. Should a fault be interrupted, the breaker must be inspected. Otherwise, a fire may result. Caution ˙Maintenance Precautions ˔Service and/or inspection of the product must be done by persons having expert knowledge. ˔Before servicing or inspecting the product, open an upstream circuit breaker or the like to isolate all sources of power. Otherwise, electric shock may result. ˔Regularly check that the breaker terminal screws are tightened to torque values shown within this manual, failure to do so may result in fire. Caution interpole barriers insulating tubes or insulating tape 8BSOJOH $BVUJPO $BVUJPO ˘ɿʠ/ʡPSʠ(ʡPSʠ1ʡ Operation Operation effort E400-NJ S400-CJ S400-˘J S400-˘E ˓(OFF)˰ʛ(ON) 110N ʛ(ON)˰˓ (OFF) 115N TRIP˰˓ (OFF) 125N x Packaged Items/Assembly Tools Breaker ɿ Instruction 1ɿ2 1ɿ3 Instruction Manual (This document) Interpole Barrier (Only FC) 86519171310 Connections/Poles Type 400AF Qty S400-CJ S 400-˘JS 400-˘E Front Connected (FC) 3P 6 M10ʷ254P 8 3P 4 M6ʷ1004P 4 Rear Connected (RC) 3P 6 M12ʷ354P 8 3P 4 M6ʷ1004P 4 3P 4 M6ʷ1204P 4 Flush Plate Where Applicable (F.P.) 3P 6 M12ʷ354P 8 3P 4 M6ʷ254P 4 Plug-in Connected (PM) ˘ɿʠ/ʡPSʠ(ʡPSʠ1ʡ

b Breaker Mounting Procedure for FC / RC ⁄1 Interpole Barrier Mounting Procedure ⁄2 Terminal Cover Mounting Procedure , Conductor Connection Procedure for RC / F.P ( Where Applicable ) n Breaker Mounting Procedure for F.P ( Where Applicable ) N L 8 ПM П* П& Flat Bar Stud T2RP40ˎS L M10ʷ20 40.2ʙ65.7Nŋm M6ʷ100 4.6ʙ6.0Nɾm ⁄3 Handle Holder / Lock Mounting Procedure ⁄4 Adjustable Thermal Magnetic Type / Electronic Type ⁄5 Time / Current Characteristic Curves Under bar is default setting. m Conductor Connection Procedure for FC ⁄0 Breaker Mounting Procedure for PM S ʢONʣ ʢOFFʣ NBYʷʢПʙʣ 1 3 2 AB C Adjustable Thermal Magnetic Type Electronic Type 0.63 0.8 8 IR(xIn) Ii(xIn) 4 6 IR Char. 0.9 0.4 0.5 0.63 0.8 0.95 IR 300 175 200 225 250 350 400 IR 225 125 150 175 200 ʢOFFʣ PS Optional Ground Fault Trip ON/OFF Switch ON GF OFF Handle Holder/Lock T2HL40 1ʣAdjustable Thermal magnetic Type ɾWhen removing, remove the items in reverse order of mounting. ɾInsulate all bare conductors of the line side until the breaker end. ɾWhen removing, remove the items in reverse order of mounting. ɾWhen removing, remove the items in reverse order of mounting. 2ʣElectronic Type 0.63 0.8 1 2.5 5 10 14 0.1S 0.2S 5,6,7 431,2 121086 I T I T /R Adjustment Range Adjustable A:125,150,175,200,225ʤAʥ B:175,200,225,250,300,350,400ʤAʥ /i Adjustment Range ʷIn xIn xIR xIn IR ɾHandle holder/ lock can be fitted in any position of ʛ(ON) and ˓(OFF). ɾWhen you use this item as the handle lock, please fit padlocks in the procedure of ᶅ. ɾWhen removing, remove the items in reverse order of mounting. M6ʷ120 4.6ʙ6.0NɾmS . Solderless Terminals Mounting Procedure for FC O ʽ25mm P ʽ240mm2 25Nŋm Q R Solderless Terminal T2FW40Wˎ Q Special Screw M8ʷ25 7ʙ9.5Nŋm ˎɿ3 or4 (Poles) ˎɿ3 or4 (Poles) A B10 Flush Plate T2FP40Sˎ ˎɿ3 or4 (Poles) ˎɿ3 or4 (Poles) J J K C ʽ30mm D ʽ12.5mm E 10.5mm F ʽ30mm G ʽ12mm H ʽ10mm I 11mm J M10ʷ25 13.7ʙ22.5Nŋm K M12ʷ35 40.2ʙ65.7Nŋm 18.6ʙ29.4Nŋm M 14mm N M12ʷ35 Flat Bar T2FB40ˎBC ˎɿ3 or4 (Poles) # M6ʷ25 4.6ʙ6.0Nɾm R2G0789SAB(KRB-5336b) T2PM40Bˎ Plug-in Base 1 2 Interpole Barrier T2BA40ˎS ˎɿ3 or4 (Poles) Terminal Cover Lock T2CF00L FC ( with Flat Bar ) Solderless Terminal T2CS40ˎS Connection FC ( without Flat Bar ) T2CF40ˎSL Terminal Cover T2CF40ˎSW RC / PM T2CR40ˎS