EDS1206-001 EUROPA | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 7
Technical content
It is the responsibility of the person installing the electrical equipment to ensure that the installation meets the requirements of the IET wiring regulations and is therefore ‘fit for purpose’. Factors such as correct selection of components, cable sizing, protective devices and Earth bonding are all critical and should be checked prior to full testing and power-up. Any other regulations applicable to the equipment being installed such as the Machinery Directive and current health and safety legislation must also be adhered to. All connections (including factory made) must be checked for the correct tightness prior to commissioning of the electrical installation. All connections should be checked periodically to ensure correct tightness. DO NOT USE POWER TOOLS ON THESE PRODUCTS Technical Data: MCCB250 (E250-SJ) IP4X Enclosed MCCBs 400
275 FIXING CENTRES
4 x HOLES 8.5 DIA TOP AND BOTTOM GLAND PLATES 2mm THICK 130 155 M8 BOLT 8 - 12Nm NOTE: TERMINAL SHROUDS NOT SHOWN FOR CLARITY 48,548,5 M10 BOLT 22 - 37Nm 278 249 MAXIMUM CABLE SIZE 2 x 120mm sq. WARNING: All connections (including factory made) must be checked for the correct tightness prior to the commissioning of the electrical installation 700
600 FIXING CENTRES
6Nm Max. M8 BOLT 8 - 12Nm MCCB250-3PNL-MC
EDS1206-001Europa House, Airport Way, Luton, Beds, LU2 9NH Tel: 01582 692 440 / Fax: 01582 692 450 e-mail: sales@europacomponents.com / website: http://www.europacomponents.com Technical Data: MCCB250 (E250-SJ) IP4X Enclosed MCCBs 400 4 x HOLES 8.5 DIA TOP AND BOTTOM GLAND PLATES 2mm THICK 130 155 NOTE: TERMINAL SHROUDS NOT SHOWN FOR CLARITY 236.8 48,548,5 48,5 145,5 249 M10 BOLT 22 - 37Nm MAXIMUM CABLE SIZE 2 x 120mm sq. MCCB250-4P-MC WARNING: All connections (including factory made) must be checked for the correct tightness prior to the commissioning of the electrical installation
Standard Optional - Not Available 250 TB2 Lite 250Frame Reference Quantity Unit C ondition Max In (A ) of Frame Model E250 Number of Poles 3, 4 Type SJ Nominal c urrent ratings In (A) 50°C 100,125, 160,200 250 E lec tric al charac teris tic s Rated operational voltage U e (V) AC 50/60 Hz 525 DC 250 Rated insulation voltage Ui (V) 800 Rated impulse voltage Uimp (kV) 8 Ultimate breaking capacity Icu (kA) 690V AC - (IEC, JIS, AS/NZS) 525V AC 7.5 440V AC 15 400/415V AC 25 220/240V AC 53 250V DC 15 Service breaking capacity Ics (kA) 690V AC - (IEC, JIS, AS/NZS) 525V AC 6 440V AC 12 400/415V AC 19 220/240V AC 27 250V DC 12 Rated breaking capacity (NEMA) (kA) 480V AC 10 240VAC 35 P rotec tion Fixed thermal, fixed magnetic - Adjustable thermal, adjustable magnetic Utilisation category A Ins tallation Front connection (FC) Extension bar (FB) Cable clamp (FW) Rear connection (RC) Plug-in (PM) - DIN rail mounting (DA) - Dimensions height (mm) 165 width (mm) 3 pole 105 4 pole 140 depth (mm) 68 Weight weight (kg) 3 pole 1.5 4 pole 1.9 Operation Direct Opening Action Toggle operation Door mounted (HS) / Breaker mounted handle (HB) Motor operation Endurance Electrical cycles 415V AC 6,000 Mechanical cycles 18,000 Page 1 of 3 DATA SHEET: TEMBREAK 2 E250-SJ MCCB
Drilling plan (front view) M4 0.7 Tapped hole M4 0.7 Mounting screw Panel cutout (front view) Detail of connecting part Mounting plate (max. t3.2) Stud can be turned 45° or 90° Panel cutout dimensions shown give an allowance of 1.0mm around the handle escutcheon. Conductor overlap, max 3P 4P ø24 35 3535 102 144 144 20 6 126 6 3516 107 72 35 35 5 35 3 35 25 22 52.5 3P 4P 52.5 53.5 1071 42 53.5 CL CLCL LH LH LH LH 23 23 Preparation of conductor With extension bars (optional) Drilling plan (front view) M4 0.7 Tapped hole Interpole barrier (removable) M8 screw Conductor overlap, max Conductor overlap, max Mounting holeP 4P 3 3P 4P 25(max.) max.t7 ø11 30.5 11.5 30.5 11.519 30.5 11.5 48.548.5 48.5 169120 35 35 35 3535 102 126 11(max.) 7 3535 10.5 6.8 ø11 30.5 11.519 Note: For the extension bars, Straight bars or Spread bars can be supplied. CL LH LH Interpole barrier (removable) Mounting hole P 4P 3 101165 144 140 105 105 M4 0.7 Mounting screw CL Outline Dimensions E250-SJ ASL: Arrangement Standard Line HL: Handle Frame Centre Line Page 2 of 3 DATA SHEET: TEMBREAK 2 E250-SJ MCCB
1040% - 1560% 100 - 200A Min Magnetic trip settings 400% - 600% Time/Current Characteristic Curves E250-SJ (100 ~ 200A) Time/Current Characteristic Curves E250-SJ (250A) 250A Min Magnetic trip settings 400% - 600% 250A Max Magnetic trip settings 880% - 1320% Page 3 of 3 DATA SHEET: TEMBREAK 2 E250-SJ MCCB
Innovators in Protection Technology 2G0947SAA(KRB-0603) ʢTypesʣ ʢ'JY Typesʣ E250-SCF E250-SF S250-SF ܗ ʢAdjustable Thermal Magnetic Typesʣ E250-SCJ E250-SJ S250-SJ ϊʔώϡʔζϒϨʔΧ औѻઆ໌ॻ Instruction Manual for Moulded Case Circuit Breakers xɹPackaged Items/Assembly Tools cɹOperating Instructions v෦ଐͷணɹFitting Internal Accessories ϒϨʔΧ Breaker ɿ औѻઆ໌ॻ Instruction 1ɿ2 1ɿ2 1ɿ3 औѻઆ໌ॻ ʢຊॻʣ Instruction Manual (This document) όϦΞʢ'$ͷΈʣ Interpole Barrier (Only FC) 8 17 65 RESET TRIPPED T2AL00L Alarm Switch ˎ T2AX00L ˎ Auxiliary Switch T2SH00L T2UV00L Shunt Trip Undervoltage Trip ˎ ˎ Ring Mark 10 mm ᶉ ᶈ ᶉ ᶈ Auxiliary Switch Alarm Switch a a contact b b contact a a contact b b contact 11/AXc-14/AXa 11/AXc-12/AXb 91 /ALc -21/AXc-24/AXa 21/AXc-22/AXb 31/AXc-34/AXa 31/AXc-32/AXb 41/AXc-44/AXa 41/AXc-42/AXb Shunt Trip power source C1-C2 Undervoltage Trip power source D1-D2 94 /ALa 91 /ALc - 92 /ALb ˎSymbols of Accessories ˎSymbols of Accessories PS ʢ53*1ʣ ᶃ ᶄ ᶅ ᶅ ᶆ ᶆ ᶆ ᶇ ᶇ μϛʔϢχοτ Dummy unit ༻Լ͍͞ɻ ɾAfter fitting, verify the function of the Accessory. ʢONʣ ϋϯυϧ Handle ʢOFFʣ τϦοϓϘλϯ Trip Button ᶄᶄᶄ ᶄ ᶄ ᶅ ᶅ AX AL SH UV V ᶌ ᶋ ᶊ ᶊ ᶍ ܗ Form the cable ిઢҾ͖ग़͠෦ͷॲཧ Pull Out Leads on Load Side औ֎͠ɹ Removal ͤɹCombination ɼ In case of fiting one (or two) auxiliaryswitch, fit in an order from a left side-slot. 3 pole4 pole ˟547ʖ0002Ճඒ౦7–2–10 ిɿ06(6791)9320 ϑΝοΫεɿ06(6791)9274 ϗʔϜϖʔδɿIUUQwww.terasaki.co.jp E-mailɿLJLJJOGP!UFSBTBLJDPKQ 7-2-10 Kamihigashi, Hiranoku, Osaka 547-0002, Japan TEL:81-6-6791-9323/ FAX:81-6-6791-9274 URLɿIUUQwww.terasaki.co.jp E-mailɿJOUTBMFT!UFSBTBLJDPKQ Please retain this manual for future reference.The Manufacturer assumes no responsibility for damages resulting from non-application or incorrect application of the instructions provided herein. z ҆શ্ͷ͝ҙ ɼ҆શͷ ͷ ɻ ইΛड͚Δ ɻ ͕͋Γ·͢ɻ রͯ͠Լ͍͞ɻʣ ༻্ͷҙ ͬͯԼ͍͞ɻ ҼͱͳΓ·͢ɻ ҼͱͳΓ·͢ɻ ෦ʹແཧͳྗ͕ ෦ͷաେͳԠྗɼ ɼϒϨʔΧ໘ ༻͠ɼઈԑςʔϓͰ ͕͋Γ·͢Ň ݥة ͷ ݥة ࢠ όϦΞ ઈԑνϡʔϒ ·ͨ ઈԑςʔϓ z Safety Notices Be sure to read these Instructions and other associated documents accompanying the product thoroughly to be familiarize yourself with the product handling, safety information, and all other precautions before mounting, using, servicing, or inspecting the product. In these Instructions, safety notices are divided into "Warning" and "Caution" according to the hazard level: : A warning notice with this symbol indicates that neglecting the suggested procedure or practice could result in lethal or serious personal injury. : A caution notice with this symbol indicates that neglecting the suggested procedure or practice could result in moderate or slight personal injury and/or property damage. Note that failing to observe notices could result in serious results in some cases. Because safety notices contain important information, be sure to read and observe them. ্ͷҙ ˙ͦͷଞͷҙ ҼͱͳΓ·͢ɻ ΛอূͰ͖·ͤΜɻ ˙Other Precautions ɾDo not carry this product by accessory leads, as this may cause damage to the product. ɾUnauthorised opening of the breaker cover will invalidate product warranty. ɾWhen installing the product, use wires or conductors, the cross sectional areas of which accommodate the rated current of the product. Using wires or conductors with inadequate cross sectional areas may cause false tripping and overheat. ͬͯԼ͍͞ɻ ҼͱͳΓ·͢ɻ ˙Mounting Precautions (For detailed mounting dimensions, refer to the TemBreak2 catalogue.) ˔Electrical work should only be undertaken by suitably qualified persons. ˔Do not place the product in an area that is subject to high temperature, high humidity, excessive dusty air, corrosive gas, strong vibration and shock, or other unusual conditions. Mounting in such areas could cause a fire or malfunction. ˔Be careful to prevent foreign objects (debris, concrete powder, iron powder, etc.) and rainwater from entering product. These materials inside the product could cause a fire or malfunction. Prior to commencing any work on the product, open an upstream circuit breaker or isolator to ensure that no voltage is applied to the product. Otherwise, electrical shock may result. ˔For 4-pole breakers, be sure to connect a neutral conductor to the N pole. Otherwise, an over-current may hinder the product from tripping, thus resulting in a fire. Caution ˙Handling Precautions ˔Never touch terminals. Otherwise, electric shock may result. Warning ˔When the breaker trips open automatically, remove the cause, then return the handle to the | (ON) position. Should a fault be interrupted, the breaker must be inspected. Otherwise, a fire may result. Caution ˔When connecting cable or busbar to the product, tighten terminal screws to the torque specified in this manual. Otherwise, a fire could result. ˔Even when tightening the terminal screws and after conductor connection, do not apply excessive force to the terminals. Otherwise, a fire may result. ˔For front-connected breakers, Insulate all bare conductors of the line side until the breaker end. If interpole barriers are packed, be sure to use the barriers; moreover, insulate all bare conductors by insulating tape or the like so that the tape overlaps with the barriers. Insufficient insulation may result in short- circuit. ˔Do not block the arc gas vents of the product to ensure adequate arc space. Blocking these vents could result in failure of circuit interruption. ˙Maintenance Precautions ˔Service and/or inspection of the product must be done by persons having expert knowledge. ˔Before servicing or inspecting the product, open an upstream circuit breaker or the like to isolate all sources of power. Otherwise, electric shock may result. ˔Regularly check that the breaker terminal screws are tightened to torque values shown within this manual, failure to do so may result in fire. Caution interpole barriers insulating tubes or insulating tape 8BSOJOH $BVUJPO $BVUJPO Operation Operation effort ˓(OFF)˰ʛ(ON) 53N ʛ(ON)˰˓ (OFF) 57N TRIP˰˓ (OFF) 91N Connections/Poles ࣜܗType E250-SCF, E250-SF, S250-SF, E250-SCJ, E250-SJ, S250-SJ ʢFCʣ Front Connection 2P 2 M4ʷ553P 2 4P 4 M8ʷ186 Qty औͶ͡ Mounting screw Qty ଓͶ͡ Connecting screw ʢRCʣ Rear Connection 2P 2 M4ʷ55 2P 4 M8ʷ253P 2 3P 6 4P 4 4P 8 ʢPMʣ Plug-in Connection 2P 2 M4ʷ65 2P 4 M83P 2 3P 6 4P 4 4P 8 ʢFPʣ Flush Plate Where Applicable 2P 2 M5ʷ15 2P 4 M8ʷ253P 2 3P 6 4P 4 4P 8
bຊମऔཁྖɹ ܗ Breaker Mounting Procedure for FC / RC ⁄1όϦΞऔཁྖ Interpole Barrier Mounting Procedure ⁄2Χόʔऔཁྖ Terminal Cover Mounting Procedure ,ܗࠐ Conductor Connection Procedure for RC / F.P ( Where Applicable ) nɹBreaker Mounting Procedure for F.P ( Where Applicable ) П* П& ̖ M4ʷ55 mm 1.3ʙ1.7Nɾm ⁄3ϋϯυϧϗϧμऔཁྖ Handle Holder Mounting Procedure ⁄5ܗ Adjustable Thermal Magnetic Type ⁄6ઢɹTime / Current Characteristic Curves Լઢ෦ඪ४ઃఆͰ͢ɻUnder bar is default setting. mɹ Conductor Connection Procedure for FC PS ᶃ ᶅ ᶄʢOFFʣ 11 9 0.63 0.8 1li(xln) lR(xln) ɾInsulate all bare conductors of the line side until the breaker end. ͍·͢ɻ ɾWhen removing, remove the items in reverse order of mounting. ͍·͢ɻ ɾWhen removing, remove the items in reverse order of mounting. ͍·͢ɻ ɾWhen removing, remove the items in reverse order of mounting. 0.63 0.8 1 11975 I T /R Adjustment Range /i Adjustment Range ʷIn xI n 0.63 0.8 1 1086 13 I T /R Adjustment Range /i Adjustment Range ʷIn xIn ( =100, 125, 160, 200A)In ( =250A)In PMEJOH ʢ0/ʣ ʢ0/ʣ )PMEJOH ʢ0''ʣ ϋϯυϧϗϧμ Handle Holder T2HH25L ⁄4ϋϯυϧϩοΫऔཁྖ Handle Lock Mounting Procedure ᶃ ᶄ ᶅ ᶆ NBYʷʢПʣ ϋϯυϧϩοΫ Handle Lock T2HL25L ͍·͢ɻ ɾWhen removing, remove the items in reverse order of mounting. ઃఆ"SSFOHNFOU4FUʢ˃ ᶄᶆ ᶃ ᶇ ᶅL L ПM 13 N ɾHandle lock can be fitted in any position of ʛ(ON) and ˓(OFF). ͍·͢ɻ ɾWhen removing, remove the items in reverse order of mounting. Solderless Terminals Mounting Procedure for FC A ᶆ ᶃ ᶅ ᶅ ᶅ ᶅ ᶄ ᶄ B ᶄ ϑϥογϡϓϨʔτ Flush Plate ˎɿ3 or4 Polesʣ J C ʽ22mm D ʽ11mm E 8.4mm F ʽ25mm G ʽ11mm H ʽ7mm I 9mm B M5ʷ15mm 3.6ʙ4.4Nɾm ༷Ͱ͢ɻ ༷Ͱ͢ɻ L M6ʷ18 mm 11.8ʙ18.6Nŋm 7.8ʙ11.8Nŋm M 9mm N M8ʷ25 mm T2FP2501SˎB ཪ໘ελου Frat Bar Stud ˎɿ2, 3 or4 Polesʣ T2RP25LˎS 2G0947SAA(KRB-0603) M8ʷ18 7.8ʙ12.7Nŋm M10ʷ25 22.5ʙ37.2NŋmK J ˎɿ2, 3 or4 Polesʣ J K όʔ Flat Bar T2FB25LˎW T2FB25LˎS όϦΞ Interpole Barrier T2BA25LˎSH ˎɿ2, 3 or4 Polesʣ ˎɿ2, 3 or4 Polesʣ ᶄ ᶄ ΧόʔϩοΫ Terminal Cover Lock T2CF20L ܗࠐࠩ Rear/Plug-in Connected (RC / PM) Connection ܗ Front Connected (FC) T2CF25LˎSS Χόʔ Terminal Cover T2CR25Lˎ T2CF25LˎSL T2CF25LˎSW T2FP2502SˎB T2FP2510SˎB T2FP2511SˎB T2FP2512SˎB ᶆ ᶄ ᶃ ᶅ 2 3 ཪ໘Ωϟοϓ ˞&4$+ &4+ Use for E250-SCJ, E250-SJ, S250-SJ End cap ࢠ Solderless Terminal ˎɿ2, 3 or4 Polesʣ T2FW25LSˎ P ʽ120mm2 Q 19Nŋm R M6ʷ20mm 6.9ʙ9.3Nŋm T2FW25LSˎ O ʾ23mm ⁄0ܗࠐࠩ Breaker Mounting Procedure for PM ͍·͢ɻ ɾWhen removing, remove the items in reverse order of mounting. ᶅ ᶅ ᶆ ʢONʣ For 4 pole, use the 4pcs mounting screw. M4ʷ65 1.3ʙ1.7NɾmS ᶄ ᶄ ᶃ ʢ0''ʣ ˎɿ2, 3 or4 Polesʣ Plug-in Base T2PM25LCˎ औ T2PM25LEˎ