M215HW01VB AUO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 28
Technical content
Datasheet sections
- 2.1 Display Characteristics
- 2.2 Optical Characteristics
- 4.1 TFT LCD Module
- 4.2 Absolute Ratings of Environment
- 5.1 TFT LCD Module
- 5.1.1 Power Specification
- 5.1.2 Signal Electrical Characteristics
- 6.1 Pixel Format Image
- 6.2 The input data format
- 6.3 Signal Description
- 6.4 Timing Characteristics
- 6.5 Timing diagram
- 6.6 Power ON/OFF Sequence
- 7.1 TFT LCD Module
- 7.1.1 Pin Assignment
- 7.2 Connector on Backlight Unit
- 7.2.1 Signal for LED light bar connector
Product Specification M215HW01 VB document version 1.1 1 ( ) Preliminary Specification (V ) Final Specification Module 21.5” Color TFT-LCD Model Name M215HW01 VB Customer Date Approved by Note: This Specification is subject to change without notice. Approved by Date Paul Huang Oct 15, 2010 Prepared by Date Ken Ho Oct 15, 2010 Desktop Display Business Group / AU Optronics corporation
Product Specification M215HW01 VB document version 1.1 3 Record of Revision Version and Date Page Old description New Description Remark 0.1 2010/05/13 All First Edition for Customer - 0.2 2010/07/01 last No packing specificaton Add p acking specification 1.0 2010/08/06 Final version 1.1 2010/10/15 4 N/A 13) Please avoid touching CO F position while you are doing mechanical design. Add. 1.1 2010/10/15 5 TCO’03 compliance TCO 5.0 compli ance Revise 1.1 2010/10/15 26 Shipping label position before change Shipping label postion after change Revise 1.1 2010/10/15
Product Specification M215HW01 VB document version 1.1 4
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay att ention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact wi th water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open or modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a Module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the LED lightbar edge. Instead, press at the far ends of the LED light bar edge softly. Otherwise the TFT Module may be damaged. 10) At the insertion or removal of the Signal Inter face Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11) After installation of the TFT Module into an en closure, do not twist nor bend the TFT Module even momentary. At designing the enclosure, it shou ld be taken into consideration that no bending/twisting forces are applied to the TFT Modu le from outside. Otherwise the TFT Module may be damaged. 12) Small amount of materials having no flammabilit y grade is used in the LCD module. The LCD module should be supplied by power complied with re quirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. 13) Please avode touching COF position while you ar e doing mechanical design.
document version 1.1 5 M215HW01 VB
2.0 General Description
This specification applies to the 21.5 inch-wide Co lor a-Si TFT-LCD Module M215HW01.The display supports the Full HD - 1920(H) x 1080(V) sc reen format and 16.7M colors (RGB 6-bits + Hi-FRC data). All input signals are 2-channel LVDS interface and this module doesn’t contain an driver board for backlight.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ℃ condition: ITEMS Unit SPECIFICATIONS Screen Diagonal [mm] 546.86(21.53”) Active Area [mm] 476.64 (H) x 268.11 (V) Pixels H x V 1920(x3) x 1080 Pixel Pitch [um] 248.25 (per one triad) ×248.25 Pixel Arrangement R.G.B. Vertical Stripe Display Mode TN Mode, Normally White White Luminance ( Center ) [cd/m 2] 250cd/m 2 (Typ.) Contrast Ratio 1000 (Typ.) Optical Response Time [msec] 5ms (Typ., on/off) Nominal Input Voltage VDD [Volt] +5.0 V Power Consumption (VDD line + LED line) [Watt] 17.6 (Typ.) (without driver board, all black pattern) Weight [Grams] 1800 (max.) Physical Size [mm] 495.6(W) × 292.2(H) × 10.3(D) Ty p. Electrical Interface Dual channel LVDS Support Color 16.7M colors (RGB 6-bit + Hi_FRC ) Surface Treatment Anti-Glare, 3H Temperature Range Operating Storage (Shipping) oC] [oC] 0 to +50 -20 to +60 RoHS Compliance RoHS Compliance TC0 Compliance TC0 5.0 Compliance
document version 1.1 6 M215HW01 VB
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃: Item Unit Conditions Min. Typ. Max. Note Horizontal (Right) CR = 10 (Left) Viewing Angle [degree] Vertical (Up) CR = 10 (Down) Contrast ratio Normal Direction 600 1000 - 3 Raising Time (TrR) - 3.8 5.5 Falling Time (TrF) - 1.2 2.5 Response Time [msec] Raising + Falling - 5 8 Red x 0.605 0.635 0.665 Red y 0.319 0.349 0.379 Green x 0.302 0.332 0.362 Green y 0.589 0.619 0.649 Blue x 0.125 0.155 0.185 Color / Chromaticity Coordinates (CIE) Blue y 0.025 0.055 0.085 White x 0.283 0.313 0.343 Color Coordinates (CIE) White White y 0.299 0.329 0.359 Central Luminance [cd/m2] 200 250 - 6 Luminance Uniformity [%] 75 80 - 7 Crosstalk (in 60Hz) [%] 1.5 8 Flicker dB -20 9
document version 1.1 7 M215HW01 VB Note 1: Measurement method The LCD module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature change during measuring (at surface 35 ℃). In order to stabilize the luminance, the measurement should be executed after lighting Backl ight for 30 minutes in a stable, windless and dark room. Note 2: Definition of viewing angle measured by ELDIM (EZContrast 88) Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180° horizontal and 180° vertical range (off-normal view ing angles). The 180° viewing angle range is broken down as follows; 90° ( ) horizontal left and right and 90° ( ) vertical, high (up) and low (down). The measurement direction is typically perp endicular to the display surface with the screen rotated about its center to develop the desi red measurement viewing angle. Center of the screen TFT-LCD Module Measured distance Photo detector LCD Panel
document version 1.1 8 M215HW01 VB Note 3: Contrast ratio is measured by TOPCON SR-3 Note 4: Definition of Response time measured by Westar TRD-100A The output signals of photo detector are measured w hen the input signals are changed from “Full Black” to “Full White” (rising time, Tr R), and from “Full White” to “Full Black” (falling t ime, Tf F), respectively. The response time is interval between the 10% and 90% (1 frame at 60 Hz) of amplitudes. Tr R + TfF = 5 msec (typ.). Note 5: Color chromaticity and coordinates (CIE) is measured by TOPCON SR-3 Note 6: Central luminance is measured by TOPCON SR-3 Note 7: Luminance uniformity of these 9 points is defined as below and measured by TOPCON SR-3 9) - (1 Points 9in LuminanceMaximum 9) - (1 points 9in LuminanceMinimum Uniformity = Note 8: Crosstalk is defined as below and measured by TOPCON SR-3 100 Optical response W hite Tr F Tr R 100 Optical response W hite Black Tr F Tr R Black
1 Frame 1 Frame
document version 1.1 9 M215HW01 VB CT = | YB – YA | / YA × 100 (%) Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) Note 9: Test Patern: Subchecker Pattern measured by TOPCON SR-3 R G B R G B R G B R G B R G B R G B Method: Record dBV & DC value with TRD-100 Level DC Hz) 30Level(at AClog20(dB)Flicker = Gray Level = L127 Gray Level = L0 Amplitude Time DC AC
document version 1.1 10 M215HW01 VB
3.0 Functional Block Diagram
The following diagram shows the functional block of the 21.5 inch Color TFT-LCD Module: I/F + X-PCB I/F PCB Interface: FI-XB30SRL-HF11(JAE) 、093F30-B0T01A(Starconn) Mating Type: FI-X30HL (Locked Type) DC +5V LVDS AUO ASIC LED Driver on system Connector DC/DC Converter LVDS Receiver Timing Controller Mini LVDS Transmitter Gamma Correction AUO ASIC LVD TFT-LCD 1920(x3) x 1080 Pixels G1080 D1 D5760 X-Driver IC Y-Driver IC LED Backlight
document version 1.1 11 M215HW01 VB
4.0 Absolute Maximum Ratings
Absolute maximum ratings of the module are as following:
4.1 TFT LCD Module
4.2 Absolute Ratings of Environment
Item Symbol Min. Max. Unit Conditions Operating Temperature TOP 0 +50 [ oC] Operation Humidity HOP 5 90 [%RH] Storage Temperature TST -20 +60 [ oC] Storage Humidity HST 5 90 [%RH] Note 3 Note 1: With in Ta (25℃) Note 2: Permanent damage to the device may occur if exceeding maximum values Note 3: For quality perfermance, please refer to AUO IIS(Incoming Inspection Standard). Operating Range Storage Range Item Symbol Min Max Unit Conditions Logic/LCD Drive Voltage VDD 0 6.0 [Volt] Note 1,2
document version 1.1 12 M215HW01 VB
5.0 Electrical characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as following: Note 1: Measurement conditions: The duration of rising time of power input is 470us. Symbol Parameter Min Typ Max Unit Conditions VDD Logic/LCD Drive Voltage 4.5 5.0 5.5 [Volt] +/-10% IDD Input Current - 0.98 1.22 [A] VDD= 5.0V, All Black Pattern At 60Hz PDD VDD Power - 4.9 6.1 [Watt] VDD= 5.0V, All Black Pattern At 60Hz IRush Inrush Current - - 3 [A] Note 1 VDDrp Allowable Logic/LCD Drive Ripple Voltage - - 500 [mV] p-p VDD= 5.0V, All Black Pattern At 75Hz
document version 1.1 13 M215HW01 VB
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when VDD i s off. Please refer to specifications of SN75LVDS82DGG (Texas Instruments) in detail. 1. DC Characteristics of each signal are as following: Symbol Parameter Min Typ Max Units Condition VTH Differential Input High Threshold - - +100 [mV] VICM = 1.2V Note 1 VTL Differential Input Low Threshold -100 - - [mV] VICM = 1.2V Note 1 │ VID│ Input Differential Voltage 100 - 600 [mV] Note 1 VICM Differential Input Common Mode Voltage +1.0 +1.2 +1.5 [V] VTH-VTL = 200MV (max) Note 1 Note 1: LVDS Signal Waveform
document version 1.1 14 M215HW01 VB 2. AC Characteristics Description Symbol Min Max Unit Note Maximum deviation of input clock frequency during SSC F DEV - ± 3 % Maximum modulation frequency of input clock during SSC F MOD - 200 KHz FMOD Freq Fmax Fcenter Fmin Fcenter * FDEV < Spread Spectrum> time
document version 1.1 15 M215HW01 VB
5.2 Backlight Unit
Parameter guideline for LED driver is under stable conditions at 25℃(Room Temperature): Symbol Parameter Min. Typ. Max. Unit Note IRLED LED Operation Current - 60 63 [mA] Note 1 VLB Light Bar Operation Voltage (for reference) 48 52.8 57.6 [Volt] Note 2 PBLU BLU Power consumption (for reference) 12.7 13.8 [Watt] Note 3 LTLED LED life Time 30000 [Hour] Note 3 Operating with fixed driving current Note 1 :The specified current is input LED chip 100% duty current. Note 2 : The value showed in the table is one light bar’s operation voltage. Note 3 : Definition of life time : brightness becomes 50% of its original value. The minimum life time of LED unit is on the condition of IRLED =60mA and 25±2℃ (Room temperature). Note 4: Each LED light bar consists of 64 pcs LED package ( 4 strings x 16 pcs / string ).
document version 1.1 16 M215HW01 VB
6.0 Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format.
6.2 The input data format
Note 1: R/G/B data 7:MSB, R/G/B data 0:LSB O = “First Pixel Data” E = “Second Pixel Data”
document version 1.1 17 M215HW01 VB
6.3 Signal Description
The module using one LVDS receiver SN75LVDS82(Texas Instruments). LVDS is a differential signal technology for LCD interface an d high speed data transfer device. LVDS transmitters shall be SN75LVDS83(negative edge samp ling). The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. PIN # SIGNAL NAME DESCRIPTION
1 RxOIN0- Negative LVDS differential data input (Odd data)
2 RxOIN0+ Positive LVDS differential data input (Odd data)
3 RxOIN1- Negative LVDS differential data input (Odd data)
4 RxOIN1+ Positive LVDS differential data input (Odd data)
5 RxOIN2- Negative LVDS differential data input (Odd data,DSPTMG)
6 RxOIN2+ Positive LVDS differential data input (Odd data,DSPTMG)
7 GND Power Ground
8 RxOCLK- Negative LVDS differential clock input (Odd clock)
9 RxOCLK+ Positive LVDS differential clock input (Odd clock)
10 RxOIN3- Negative LVDS differential data input (Odd data)
11 RxOIN3+ Positive LVDS differential data input (Odd data)
12 RxEIN0- Negative LVDS differential data input (Even data)
13 RxEIN0+ Positive LVDS differential data input (Even data)
14 GND Power Ground
15 RxEIN1- Positive LVDS differential data input (Even data)
16 RxEIN1+ Negative LVDS differential data input (Even data)
17 GND Power Ground
18 RxEIN2- Negative LVDS differential data input (Even data)
19 RxEIN2+ Positive LVDS differential data input (Even data)
20 RxECLK- Negative LVDS differential clock input (Even clock)
21 RxECLK+ Positive LVDS differential clock input (Even clock)
22 RxEIN3- Negative LVDS differential data input (Even data)
23 RxEIN3+ Positive LVDS differential data input (Even data)
24 GND Power Ground
25 NC No connection (for AUO test only. Do not connect) 26 NC No connection (for AUO test only. Do not connect) 27 NC No connection (for AUO test only. Do not connect)
28 VDD Power +5V
29 VDD Power +5V
30 VDD Power +5V
Note1: Start from left side
document version 1.1 18 M215HW01 VB Note2: Input signals of odd and even clock shall be the same timing.
6.4 Timing Characteristics
Basically, interface timing described here is not a ctual input timing of LCD module but close to output timing of SN75LVDS82DGG (Texas Instruments) or equivalent. Item Symbol Min Typ Max Unit Data CLK Tclk [MHz] Period Th 1034 1060 2047 [Tclk] Display Area Tdisp(h) 960 960 960 [Tclk] H-section Blanking Tblk(h) 74 100 1087 [Tclk] Period Tv 1088 1120 2047 [Th] Display Area Tdisp(h) 1080 1080 1080 [Th] V-section Blanking Tblk(h) 8 40 967 [Th] Frame Rate F 50 60 75 [Hz] Note : DE mode only
document version 1.1 19 M215HW01 VB
6.5 Timing diagram
document version 1.1 20 M215HW01 VB
6.6 Power ON/OFF Sequence
VDD power and lamp on/off sequence are as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Value Parameter Min. Max. Unit T1 0.5 10 [msec] T2 0 50 [msec] T3 500 - [msec] T4 200 - [msec] T5 0 50 [msec] T6 1000 - [msec]
document version 1.1 21 M215HW01 VB
7.0 Connector & Pin Assignment
Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.
7.1 TFT LCD Module
Connector Name / Designation Interface Connector / Interface card Manufacturer JAE, Starconn Type Part Number FI-XB30SRL-HF11(JAE) 093F30-B0T01A(Starconn) Mating Housing Part Number FI-X30HL (Locked Type)
7.1.1 Pin Assignment
Pin# Signal Name Pin# Signal Name
1 RxOIN0- 2 RxOIN0+
3 RxOIN1- 4 RxOIN1+
5 RxOIN2- 6 RxOIN2+
7 GND 8 RxOCLKIN-
9 RxOCLKIN+ 10 RxOIN3-
11 RxOIN3+ 12 RxEIN0-
13 RxEIN0+ 14 GND
15 RxEIN1- 16 RxEIN1+
17 GND 18 RxEIN2-
19 RxEIN2+ 20 RxECLKIN-
21 RxECLKIN+ 22 RxEIN3-
23 RxEIN3+ 24 GND
25 NC (for AUO test only. Do not connect) 26 NC (for AUO test only. Do not connect) 27 NC (for AUO test only. Do not connect)
28 VDD
29 VDD 30 VDD
document version 1.1 22 M215HW01 VB 7.2 Connector on Backlight Unit. This connector is mounted on LED light-bar. Connector Name / Designation Light Bar Connector Manufacturer CVILUX Type Part Number CI1406M1HRB-NH
7.2.1 Signal for LED light bar connector
Pin no. Signal name
1 ILED (current out)
2 ILED (current out)
3 VLED (voltage in)
4 VLED (voltage in)
5 ILED (current out)
6 ILED (current out)
document version 1.1 23 M215HW01 VB
8.0 Reliability Test
Environment test conditions are listed as following table. Items Required Condition Note Temperature Humidity Bias (THB) Ta= 50℃, 80%RH, 300hours High Temperature Operation (HTO) Ta= 50℃, 50%RH, 300hours Low Temperature Operation (LTO) Ta= 0℃, 300hours High Temperature Storage (HTS) Ta= 60℃, 300hours Low Temperature Storage (LTS) Ta= -20℃, 300hours Vibration Test (Non-operation) Acceleration: 1.5 Grms Wave: Random Frequency: 10 - 200 Hz Sweep: 30 Minutes each Axis (X, Y, Z) Shock Test (Non-operation) Acceleration: 50 G Wave: Half-sine Active Time: 20 ms Direction: ±X, ±Y, ±Z (one time for each Axis) Drop Test Height: 60 cm, package test Thermal Shock Test (TST) -20℃/30min, 60℃/30min, 100 cycles 1 On/Off Test On/10sec, Off/10sec, 30,000 cycles Contact Discharge: ± 8KV, 150pF(330 ) 1sec, 8 points, 25 times/ point. ESD (Electro Static Discharge) Air Discharge: ± 15KV, 150pF(330 ) 1sec 8 points, 25 times/ point. Altitude Test Operation:10,000 ft Non-Operation:30,000 ft Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature change. A cycle of rapid temperature ch ange consists of varying the temperature from -20 to 60 , and back again. Power is not applied dur ing the test. After temperature cycling, the ℃ ℃ unit is placed in normal room ambient for at least 4 hours before power on. Note 2: EN61000-4-2, ESD class B: Certain performance degradation allowed No data lost Self-recoverable No hardware failures.
document version 1.1 24 M215HW01 VB
9.0 Shipping Label
document version 1.1 25 M215HW01 VB n the panel as shown below: Note 1: For Pb Free products, AUO will add for identification. Note 2: For RoHS compatible products, AUO will add for identification. Note 3: For China RoHS compatible products, AUO will add for identification. Note 4: The Green Mark will be presented only when the green documents have been ready by AUO Internal Green Team M215HW01 V.B
document version 1.1 26
10.0 Mechanical Characteristics
document version 1.1 27
document version 1.1 28 11. Packing Specification Stretch film Label Corner angle PET band Moisture-proof filmCorner angle Pallet 2. Pallet and shipment information SpecificationSpecificationSpecificationSpecification ItemItemItemItem Q'tyQ'ty Q'tyQ'ty DimensionDimensionDimensionDimension Weight(kg)Weight(kg)Weight(kg)Weight(kg) RemarkRemarkRemarkRemark 1 Panel 1 556(H)mm x 323(V)mm x 17.1(D)mm 1.75 2 Cushion 1 - 1.11 3 Box 1 568(L)mm x 277(W)mm x 382(H)mm 1.035 without Panel & cushion 4 Packing Box 10 pcs/Box 568(L)mm x 277(W)mm x 382(H)mm 19.6 with panel & cushion
5 Pallet 1 1150(L)mm x 840(W)mm x 138(H)mm 12
6 Pallet after Packing 18 boxes/pallet 1150(L)mm x 840(W)mm x 1286(H)mm 365.6