G104SN03V.0 | DigiCamel IC Datasheet

Online Datasheet

Read G104SN03V.0 online.

G104SN03V.0 AUO | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 25

Technical content

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 2/26 Version: 1.0 Total Pages: 26 Date: February 6, 2004 Product Functional Specification 10.4 inch SVGA Color TFT LCD Module Model Name: G104SN03 V.0 (u) Preliminary Specification ( ) Final Specification Note: This Specification is subject to change without notice.

1.0 Handling Precautions 5

2.0 General Description 6

2.1 Display Characteristics

2.2 Functional Block Diagram

3.0 Absolute Maximum Ratings 9

4.0 Optical Characteristics 10

5.0 Signal Interface 12

5.1 Connectors

5.2 Signal Pin

5.3 Signal Description

5.4 Signal Electrical Characteristics

6.0 Pixel Format Image 16

7.0 Power Consumption 17

8.0 Interface Timing 19

8.1 Display Color v.s. Input Data Signal

8.2 Input Signal Timing

8.3 Display Position

9.0 Backlight Characteristics 23

10.0 Reliability Test Items 24

11.0 Display Quality 24

12.0 Packing Dimension 25

13.0 Mechanical Characteristic 26

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 4/26 II. Record of Revision Version and Date Page Old description New Description Remark 1.0 Feb. 6, 2004 All N/A First Edition for Customers

1.0 Handing Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnection from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the interface Connector of the TFT module. 11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module should be supplied by power complied with requirements of Limited Power Source, or be applied exemption. 14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit. Do not connect the CFL in Hazardous Voltage Circuit.

2.0 General Description

This specification applies to the 10.4 inch color TFT LCD module G104SN03 V.0. This module is designed for General Display. The screen format is intended to support the SVGA (800(H) x 600(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface compatible. The module does not contain an inverter card for backlight.

Features

SVGA 800(H) x600(V) resolution - 1 CCFL(Cold cathode Fluorescent Lamp) - High contrast ratio, High transmittance ratio - Wide viewing angle - High speed response - Low power consumption - LVDS interface

Applications

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 7/26 The following items are characteristics summary on the table under 25℃ condition ： Items Unit Specifications Screen Diagonal [inch] 10.4 ” Outline dimension [mm] 236.0(W) x 174.3(H) x 5.6(D) Active Area [mm] 211.2(H) x 158.4(V) Resolution H x V 800(R, G,B x3) x 600 Pixel Pitch [mm] 0.264(H) x 0.264(V) Pixel Arrangement R.G.B. Vertical Stripe Display Mode TN mode, Normally White Typical White Luminance (ICFL=4.5 mA) [cd/m 2] 230 Typ. (center) Contrast Ratio 500：1 Typ. Optical Rise Time/Fall Time [msec] 10/25 Typ. Viewing angle (CR≧10) 60/60/35/65 (L/R/U/D) Nominal Input Voltage VDD [Volt] +3.3 Typ. Typical Power Consumption (VDD line + VCFL line) [Watt] 3.3 Typ Weight [Grams] 280 Typ ± 10 Surface treatment Anti-glare,hard coating 3H Electrical Interface 1 channel LVDS Support Color Native 262K colors (RGB 6-bit driver) Temperature Range Operating Storage(Shipping) [℃] [℃] 0 to +50 -20 to +60

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 8/26 The following diagram shows the functional block of the 10.4 inches Color TFT LCD Module：

3.0 Absolute Maximum Ratings (GND = 0 V)

Min. Max. Unit Remark Power voltage VDD -0.3 4 [Volt] At 25℃ Input signal voltage Vin -0.3 VDD+0.3 [Volt] At 25℃ CCFL current ICFL 3.0 5.5 [mA]rms CCFL starting Voltage Vs - 800 [Vrms] AT 25℃ Operating temperature Top 0 +50 [℃] Note 1 Operating Humidity HOP 8 90 [%RH] Note 1 Storage temperature TST -20 +60 [℃] Note 1 Storage Humidity HST 5 90 [%RH] Note 1 Vibration 1.5,10~200~1 [G,Hz] Shock 200,2 [G,ms] Half sine wave Note 1:The relative humidity must not exceed 90% non-condensing at temperatures of 40 ℃ or less. At temperatures greater than 40 ℃, the wet bulb temperature must not exceed 39 ℃. When operate at low temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced. Note 2:The unit should not be exposed to corrosive chemicals. Wet bulb temperature chart Twb=39°C Operating Range Storage Range

4.0 Optical Characteristics (Note 1, Note 2)

Min. Typ. Max. Unit Remark Response time Rising time Falling time Tr Tf θ=0° ms Note 4 Contrast ratio CR θ=0° 400 500 - Note 3,5 Viewing angle Top Bottom Left Right CR≧10 deg. Note 3,6 White Luminance (ICFL=4.5 mA) [cd/m2] θ=0° 200 230 - nit Note 3,7,8,9 Wx 0.280 0.320 0.340 Wy 0.300 0.330 0.360 Rx 0.540 0.570 0.600 Ry 0.290 0.320 0.350 Gx 0.270 0.300 0.330 Gy 0.530 0.560 0.590 Bx 0.115 0.145 0.175 Color chromaticity(CIE) By θ=0° 0.100 0.130 0.160 Note 3,8,9 White uniformity δW 13 Points - - 1.33 Note 3,9,10 Note 1: Ambient temperature = 25 ℃. Note 2: To be measured in dark room after backlight warm up 30 minutes. Note 3: To be measured with a viewing cone of 1 °by Topcon luminance meter BM-5A. Note 4: Definition of response time: The output signals of BM-7 are measured when the input signals are changed from “Black” to “White” (falling time) and from “White” to “Black” (rising time), respectively. The response time means the interval between the 10% and 90% of amplitudes. Refer to figure as below. Note 5. Definition of contrast ratio: Contrast ratio is calculated with the following formula. Contrast ratio (CR)= Luminance on the white raster Luminance on the black raster Sig nal ela tiv e Tr Tf "White""White" 10% 90% 100% “Black”

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 11/26 Note 6: Definition of viewing angle: Note 7: Definition of the 13 points (from A to M) on panel, refer to figure as below Note 8: Definition of brightness: the luminance of center points (G). Note 9: Driving conditions for CCFL : I L=4.5 mA, 60KHz Frequency Note 10: Definition of white uniformity: θ δw = Maximum Luminance of thirteen points (brightness) Minimum Luminance of thirteen points (brightness) θ

5.0 Signal Interface

Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation For Signal Connector Manufacturer HIROSE Type / Part Number HRS DF 19K-20P-1H Mating Connector / Part Number HRS DF19G-20S-1C (WIRE TYPE)) Mating Connector / Part Number HRS DF19-20S-1F (FPC TYPE) Connector Name / Designation For Lamp Connector Manufacturer JST Type / Part Number BHSR-02VS-1 Mating Connector / Part Number SM02B-BHSS-1-TB (1)Input signal interface Pin no Symbol Function Etc. 1 V CC +3.3 V power supply 2 V CC +3.3 V power supply

3 GND Ground

4 GND Ground

5 RxIN0-

6 RxIN0+

LVDS receiver signal channel 0

7 GND Ground

8 RxIN1-

9 RxIN1+

LVDS receiver signal channel 1

10 GND Ground

11 RxIN2-

12 RxIN2+

LVDS receiver signal channel 2

13 GND Ground

14 CKIN-

15 CKIN+

LVDS receiver signal clock

16 GND Ground

17 NC No Connection

18 NC No Connection

19 GND Ground

20 GND Ground

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 13/26 (2)LVDS transmitter/receiver signal mapping Symbol Function TxIN0 R0 Red data (LSB) TxIN1 R1 Red data TxIN2 R2 Red data TxIN3 R3 Red data TxIN4 R4 Red data TxIN5 R5 Red data (MSB) 6 bit red display data TxIN6 G0 Green data (LSB) TxIN7 G1 Green data TxIN8 G2 Green data TxIN9 G3 Green data TxIN10 G4 Green data TxIN11 G5 Green data (MSB) 6 bit green display data TxIN12 B0 Blue data (LSB) TxIN13 B1 Blue data TxIN14 B2 Blue data TxIN15 B3 Blue data TxIN16 B4 Blue data TxIN17 B5 Blue data (MSB) 6 bits blue display data TxIN18 Hs Horizontal sync. TxIN19 Vs Vertical sync. TxIN20 DE Data enable TxCLKIN CLK Clock Dot clock

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 14/26 The module using a LVDS receiver. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS84 (negative edge sampling) or compatible. Note：Input signals shall be low or Hi-Z state when VDD is off. Signal Name Description +RED5 +RED4 +RED3 +RED2 +RED1 +RED0 Red Data 5 (MSB) Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 (LSB) Red-pixel Data Red-pixel Data Each red pixel’s brightness data consists of these 6 bits pixel data. +GREEN5 +GREEN4 +GREEN3 +GREEN2 +GREEN1 +GREEN0 Green Data 5 (MSB) Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 (LSB) Green-pixel Data Green-pixel Data Each green pixel’s brightness data consists of these 6 bits pixel data. +BLUE5 +BLUE4 +BLUE3 +BLUE2 +BLUE1 +BLUE0 Blue Data 5 (MSB) Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 (LSB) Blue-pixel Data Blue-pixel Data Each blue pixel’s brightness data consists of these 6 bits pixel data. CLK Data Clock The typical frequency is 40MHz. The signal is used to strobe the pixel data and DE signals. All pixel data shall be valid at the falling edge when the DE signal is high. DE Display Timing This signal is strobed at the falling edge of CLK. When the signal is high, the pixel data shall be valid to be displayed. VSYNC Vertical Sync The signal is synchronized to CLK. HSYNC Horizontal Sync The signal is synchronized to CLK. Note：Output signals from any system shall be low or Hi-Z state when VDD is off. Signal Name Description RxIN0-, RxIN0+ LVDS differential data input (Red0-Red5, Green0) RxIN1-, RxIN1+ LVDS differential data input (Green1-Green5, Blue0-Blue1) RxIN2-, RxIN2+ LVDS differential data input (Blue2-Blue5, Hsync, Vsync, DE) CKIN-, CKIN+ LVDS differential clock input VDD +3.3V Power Supply GND Ground NC No Connection

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 15/26 Input signals shall be low or Hi-Z state when VDD is off. It is recommended to refer the specifications of SN75LVDS86(Texas Instruments) in detail. Signal electrical characteristics are as follows： Item Symbol Min. Typ. Max. Unit The differential level ｜VID｜ 0.1 - 0.6 V The common mode input voltage VIC - V The input setup time tsu 0.5 - - ns The input hold time thd 0.5 - - ns High-level input voltage V IAP 2.0 V Low-level input voltage V IAM 0.8 V Clock frequency CLK 31 68 MHz 2.4－︱VID︱︱VID︱

6.0 Pixel Format Image

Following figure shows the relationship of the input signals and LCD pixel format： R G B R G B R G B R G B R G B R G B R G B R G B 1 2 799 800 1st Line 600th Line

7.0 Power Consumption

Input power specifications are as follows： Item Symbol Min. Typ. Max. Unit Remark Input voltage V CC 3.0 3.3 3.6 V IA 230 mArms Current consumption IB 260 310 mArms Note 1 Power supply voltage Inrush current I RUSH - - 1500 mApeak Note 2 Low voltage VIL 0 - 0.3 V CC Internal logic High voltage VIH 0.7V CC - V CC Power ripple voltage VRP - - 100 mVp-p LCD Drive power consumption PDD 0.76 [Watt] Note 1:Effective value (mArms) at VCC = 3.3 V/25℃. Note 2: Refer to the following power-on condition. Sequence of Power-on/off and signal-on/off Power Input signal IA IB Black ( 0 ) Gray ( 7 ) White Black 50ms≦T1＜80msec 0≦T2＜70msec 300msec≦T3 300msec≦T4 T5≦10msec 90% 10% Ton=470μs±10% Vcc T2T1

64 Grayscale Vertical stripe line

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 18/26 Apply the lamp voltage within the LCD operating range. When the backlight turns on before the LCD operation or the LCD turns off before the backlight turns off, the display may momentarily become abnormal. Caution The above on/off sequence should be applied to avoid abnormal function in the display. In case of handling: Make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector.

8.0 Interface Timings

8.1 Display color v.s. input data signals: Data signal (0 : Low level, 1: High level) Display colors R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Basic colors Black Blue Red Magenta Green Cyan Yellow White Red grayscale Black Dark bright Red Green grayscale Black Dark bright Green Blue grayscale Black Dark bright Blue Note : Each basic color can be displayed in 64 gray scales using the 6 bit data signals. By combining the 18-bit data signals(R, G, B), the 262, 144 colors can be achieved on the display.

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 20/26 8.2. Input signal timing (1). Timing characteristics of input signals (a) DE mode Item Symbol Min. Typ. Max. Unit Remark Clock frequency Fck 36 40 50 MHz Horizontal blanking Thb1 18 256 624 Clk Vertical blanking Tvb1 3 28 184 Th (b) HV mode Item Symbol Min. Typ. Max. Unit Remark Clock frequency Fck 36 40 50 MHz Hsync period Th 818 1056 1424 Clk Hsync pulse width Thw 2 128 - Clk Hsync front porch Thf 8 40 - Clk Hsync back porch Thb 4 88 - Clk Hsync blanking Thb1 18 256 624 Clk Vsync period Tv 603 628 784 Th Vsync pulse width Tvw 1 4 - Th Vsync front porch Tvf 0 1 - Th Vsync blanking Tvb1 3 28 184 Th Hsync/Vsync phase shift Tvpd 2 320 - Clk Item Symbo l Value Unit Description Horizontal display start The 218 Clk After falling edge of Hsync, counting 218clk, then getting valid data from 219th clk’s data. Vertical display start Tve 25 Th After falling edge of Vsync, counti ng 25th, then getting 26th Th ’s data.

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 21/26 (2). Timing Definition: 628H 1056 dot 128 dot 88 dot 40 dot 800 dot H-Sync DE 28H 1H 23H 600H V-Sync DE

(C) Copyright AU Optronics, Inc. 2004 All Right Reserved. G104SN03 V.0 No Reproduction and Redistribution Allowed. 22/26 (3)Timing Chart: Vs Hs RGB DE Hs CLK RGB DE Vs Hs X,599 X,600 Invalid X,1 X,2 X,3 X,600 X,599 Invalid Tvw Tv Th Tvf Tve Tvf Tvbl Tvd 800,Y 1,Y 2,Y 3,Y 799,Y 800,Y invalid VIH VIL VIH VIL RGB,DE,Hs CLK VIH VIL VIH VIL Tcl Tch Tdh,Teh,Thh Tds,Tes,Ths Tvpd Thb Thw Thd Thbl (1 pixel / clock) Thf invalid The Thf Th Timing chart

9.0 Backlight Characteristic

Backlight driving conditions Parameter Symbol Min. Typ. Max. Unit Remark Lamp voltage V L 510 560 610 Vrms Note 1 Lamp current IL 3.0 4.5 5.5 mArms Note 1 Power consumption PL - 2.52 - W Note 2 - - 1050 T=0 ℃ Lamp starting voltage V S - - 800 Vrms T=25℃ Frequency F L - 60 - KH Z Note 3 Lamp life time L L 10000 20000 - Hr Note 1, 4 Note 1: T= 25℃, IL = 4.5mA Note 2: Inverter should be designed with the characteristic of lamp. When you are designing the inverter, the output voltage of the inverter should comply with the following conditions. (1). The area under the positive and negative cycles of the waveform of the lamp current and lamp voltage should be area symmetric(the symmetric ratio should be larger than 90%). (2). There should not be any spikes in the waveform. (3). The waveform should be sine wave as possible. (4). Lamp current should not exceed the maximum value within the operating Temperature (It is prohibited to over the maximum lamp current even if operated in The non-guaranteed temperature). When lamp current over the maximum value for a long time, it may cause fire. Therefore, it is recommend that the inverter should have the current limited circuit. Note 3: Lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. Therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. Note 4: Brightness (IL=4.5mA) to be decrease to the 50% of the initial value. Signal for Lamp connector Pin no. Symbol Function Remark 1 H CCFL power supply(H.V.) Cable color: Pink

2 L CCFL power supply(GND) Cable color: White

10.0 Reliability test items

Test tem Test Condition Remark High temperature storage 70℃, 300Hrs Note 1, 2 , 3 Low temperature storage -20℃, 300Hrs Note 1, 2 , 3 High temperature & high humidity operation 40℃, 90%RH, 300Hrs (No condensation) Note 1, 2 , 3 High temperature operation 50℃, 300Hrs Note 1, 2 , 3 Low temperature operation 0℃, 300Hrs Note 1, 2 , 3 Temperature cycling (non-operation) -20℃~60℃ 1H, 10mins, 1H, 5cycles Note 1, 2 , 3 Electrostatic discharge (non-operation) 150 pF,150Ω,10kV,1 second, 8 position on the panel, 10 times each place Note 3 Vibration (non-operation) Sweep:1.5G, 10HZ ~ 200HZ ~ 10HZ /2.5min X, Y, Z, 3 directions Note 1, 2 , 3 Mechanical shock (non-operation) 50G/18ms, 200G/2ms, ±X, ±Y, ±Z once for each direction Note 1, 2 , 3 Note 1: Evaluation should be tested after storage at room temperature for one hour. Note 2: There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. Note 3: Judgment: 1. Function OK 2. No serious image quality degradation

11.0 Display quality

The display quality of the color TFT-LCD module should be in compliance with the AUO’s OQC inspection standard.

12.0 Packing Dimension:

Max. Capacity : 30 LCD Modules/Carton. NOTE : 3. Meas : 448 mm*402mm*350mm. 2. Max. Weight : 13Kg/Carton. Anti-Static Bag LCD Module EPP Cushion Carton

13.0 Mechanical Characteristic

Product Information

G104SN03V.0 specifications and overview.

Summary

10.4 inch SVGA Color TFT LCD Module

Description

10.4 inch SVGA Color TFT LCD Module

Source title G104SN03V.0 Datasheet(PDF) - AU Optronics Corp.,

Related Parts

More parts from the same family.

Browse manufacturer