M190EG01V0 AUO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 31
Technical content
Datasheet sections
- 2.1 Display Characteristics
- 4.1 Absolute Ratings of TFT LCD Module
- 4.2 Absolute Ratings of Backlight Unit
- 4.3 Absolute Ratings of Environment
- 5.1 TFT LCD Module
- 5.2 Backlight Unit
- 6.1 Pixel Format Image
- 6.2 The Input Data Format
- 6.4 Interface Timing
- 6.5 Power ON/OFF Sequence
- 7.1 TFT LCD Module
- 7.2 Backlight Unit
document version 0.5 1/31 M190EG01 V0 ( V ) Preliminary Specification ( ) Final Specification Module 19.0” SXGA Color TFT-LCD Model Name M190EG01 V0 Customer Date Approved by Note: This Specification is subject to change without notice. Checked & Approved by Date CC Chiu Dec 27, 2005 Prepared by Dec 27, 2005 Desktop Display Business Group / AU Optronics corporation
document version 0.5 3/31 M190EG01 V0 Record of Revision Version & Date Page Old Description New Description Remark 0.1 2005/8/14 All First Edition for Customer 0.2 2005/9/06 6 Active Area 396 (H) x 324 (V) Active Area 396.32 (H) x 301.056 (V) Revised
6 Power Consumption
TBD W(Typ) Power Consumption
28 W(Typ)
6 Weight
2,700(Max) Weight 2,500 (Typ) ; 2,700(Max) Add
7 Response time
5.2 Backlight Unit
(ViCFL, Ta= 0)℃ 1500 CCFL Ignition Voltage (ViCF, Ta= 25)℃ 1160 CCFL Operation Voltage (VCFL) TBD TBD CCFL Power Consumption(PCFL) TBD TBD (ViCFL, Ta= 0)℃ 1690 CCFL Ignition Voltage (ViCF, Ta= 25)℃ 1300 CCFL Operation Voltage (VCFL) 653 @7.5m A 796 3mA CCFL Power Consumption(PCFL) 19.6 20.56 Add
6.4.1 Timing Characteristics
Signal Item Symbol Min Typ Max Unit Period Tv 1035 - 2048 Th Active Tdisp(v) 1024 1024 1024 Th Vertical Section Blanking Tbp(v)+Tfp(v)+PWvs 11 - 1024 Th Period Th 720 - 1024 Tclk Active Tdisp(h) 640 640 640 Tclk Horizontal Section Blanking Tbp(h)+Tfp(h)+PWhs 80 - 384 Tclk l Min Typ Max Unit Data CLK Tclk 30 54 83 MHz Period Th 720 844 1024 Tclk H-section Display Area Tdisp(h 640 640 640 Tclk Period Tv 1035 1066 2048 Th V-section Display Area Tdisp(v 1024 1024 1024 Th Frame Rate F 50 60 75 Hz Revised
document version 0.5 4/31 M190EG01 V0 Version & Date Page Old Description New Description Remark
6.5 Power ON/OFF Sequence
Value Parameter Min. Typ. Max. T1 0.5 - 10 T2 0.5 40 50 T3 200 - - T4 100 - - T5 0 16 50 T6 - - 10 T7 1000 - - Value Parameter Min. Typ. Max. T1 0.5 - 10 T2 0 - 50 T3 0 - 50 T4 500 - - T5 200 - - T6 200 - - T7 1000 - - revised
7.2.1 Signal for Lamp connector
Pin No. Input Color
1 Hot1 Pink
2 Cold1 White
1 Hot2 Pink
2 Cold2 White
Pin No. Input Color
2 Cold1 Black
1 Hot2 Blue
0.3 2005/10/24 16 Logic/LCD Drive Voltage Load Capacitance 20uF Logic/LCD Drive Voltage ±10% Revised IDD(Input Current) Typ =TBD Max=TBD IDD(Input Current) Typ =1.5A Max=1.7A Modifie d PDD(VDD Power) Typ =TBD Max=TBD PDD(VDD Power) Typ =7.5W Max=9.0W Modifie d Irush(Inrush Current) Max=TBD Irush(Inrush Current) Max=3.0A Modifie d Note 2: Measurement conditions: VDD rising time 0.5ms Note 2: Measurement conditions: VDD rising time 470 us Modifie d Value Parameter Min. Typ. Max. T1 0.5 - 10 T2 0 - 50 T3 0 - 50 T4 500 - - T5 200 - - T6 200 - - T7 1000 - - Value Parameter Min. Typ. Max. T1 0.5 - 10 T2 0 - 50 T3 200 - - T4 200 - - T5 0 16 50 T6 - - 10 T7 500 - - Revised
document version 0.5 5/31 M190EG01 V0 Version & Date Page Old Description New Description Remark 0.4 2005/11/7 8 2.1 Display Characteristics Contrast Ratio: 1000:1(typ)
2.1 Display Characteristics
Contrast Ratio: 1300:1(typ)
2.2 Optical Characteristics
Contrast Ratio: 1000:1(typ) 700:1 (min) Contrast Ratio: 1300:1(typ) 1000:1 (min) 0.5 2005/12/27 15 5.1.1 Power Specification IDD(Input Current): Max=1.7
5.1.1 Power Specification
IDD(Input Current): Max=1.8 Revised 15 5.1.1 Power Specification Irush(Inrush Current): Tpy= - Irush(Inrush Current): Tpy= 2 Added 15 5.1.1 Power Specification VDDrp description Delete VDDrp description Revised 29 10. Mechanical Characteristics 10. Mechanical Characteristics 2D drawing updated Revised
document version 0.5 6/31 M190EG01 V0 1. Handling Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open or modify the Module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a Module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL reflector edge. Instead, press at the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. 14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit (IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
document version 0.5 7/31 M190EG01 V0 2. General Description M190EG01 V0 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD panel, a driver circuit, and backlight system. The screen format is intended to support the SXGA (1280(H) x 1024(V)) screen and 16.7M colors (RGB 8-bits data). All input signals are LVDS interface compatible. Inverter card of backlight is not included. M190EG01 V0 is designed for a display unit of personal computer.
document version 0.5 8/31 M190EG01 V0 The following items are characteristics summary on the table under 25 ℃ condition: Items Unit Specifications Screen Diagonal [mm] 482.6 (19.0" ) Active Area [mm] 376.32 (H) x 301.056 (V) Pixels H x V 1280(x3) x 1024 Pixel Pitch [mm] 0.294 (per one triad) x 0.294 Pixel Arrangement R.G.B. Vertical Stripe Display Mode Normally Black White Luminance [cd/m 2] 300 (center, Typ) @ 7.5mA Contrast Ratio 1300 : 1 (Typ) Optical ResponseTime [msec] 8ms GTG (Avg. Typ.); 20 ms(Typ, on/off) Nominal Input Voltage VDD [Volt] +5.0 V Power Consumption [Watt]
28 W (Typ)
(w/o Inverter, All white pattern) Weight [Grams] 2500 (Typ) ; 2700 (Max) Physical Size (H x V x D) [mm] 396 (H) x 324 (V) x 17.5 (D) (Typ) Electrical Interface Dual channel LVDS Surface Treatment Hard-coating (3H), Non-Glare treatment Support Color 16.7M colors (RGB 8-bit data) Temperature Range Operating Storage (Non-Operating) [oC] [oC] 0 to +50 -20 to +60 RoHS Compliance RoHS Compliance
document version 0.5 9/31 M190EG01 V0 The optical characteristics are measured under stable conditions at 25 ℃ (Room Temperature): Item Unit Conditions Min. Typ. Max. Note Horizontal (Right) CR = 10 (Left) 89 - Viewing Angle [degree] Vertical (Up) CR = 10 (Down) 89 - Luminance Uniformity [%] 9 Points 75 80 - 2, 3 Rising 15 25 4,6 Falling 5 15 4,6 Rising + Falling 20 40 4,6 Response time [msec] Grey to Grey (Avg.) - 8 16 4,6 Red x 0.617 0.647 0.677 Red y 0.31 0.34 0.37 Green x 0.263 0.293 0.323 Green y 0.571 0.601 0.641 Blue x 0.112 0.142 0.172 Blue y 0.037 0.067 0.099 White x 0.283 0.313 0.34 Color / Chromaticity Coordinates (CIE 1931) White y 0.299 0.329 0.359 White Luminance (At CCFL= 7.5mA) [cd/m ] 240 300 - 4 Contrast Ratio 1000 1300 - 4 Cross Talk (At 75Hz) [%] - - 1.5 5 Flicker [dB] - - -20 7 Optical Equipment: BM-5A, PR880, SR3, CS1000 or equivalent.
document version 0.5 10/31 M190EG01 V0 Note 1: Definition of viewing angle Viewing angle is the measurement of contrast ratio ≧10, at the screen center, over a 180 ° horizontal and 180° vertical range (off-normal viewing angles). The 180 ° viewing angle range is broken down as follows; 90° (θ) horizontal left and right and 90 ° (Φ) vertical, high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. Note 2: 9 points position Note 3: The luminance uniformity of 9 points is defined by dividing the maximum luminance values by the minimum test point luminance Minimum Luminance of 9 points δW9 = Maximum Luminance of 9 points 50 % 90 % 90 % 50 % 10 % 10 %
document version 0.5 11/31 M190EG01 V0 Note 4: Measurement method The LCD module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a stable, windless and dark room. Note 5: Definition of Cross Talk (CT) CT = | YB – YA | / YA × 100 (%) Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) Center of the screen TFT-LCD 50 cm Photo detector LCD Panel Field=2°
document version 0.5 12/31 M190EG01 V0 Note 6: Definition of response time: Algorithm: 16 B Level - A Level ≥ then the average of Grey-to-Grey response time is 8ms. ( F= 60 Hz). TrR(rising time; from “All Black” to “All White ”) + TrF(Falling time; from “All White” to “All Black”) = 20ms(typ). 10% 90% 100% Time Time Optical Response Driving Signal A B TrTf
document version 0.5 13/31 M190EG01 V0 Note 7: Subchecker Pattern R G B R G B R G B R G B G B R G B Method: Record dBV & DC value with (WESTAR)TRD-100 Level DC Hz) 30Level(at AClog20(dB)Flicker = Gray Level = L127 Gray Level = L0 Amplitude Time DC AC
document version 0.5 14/31 M190EG01 V0 3. Functional Block Diagram The following diagram shows the functional block of the 19.0 inches Color TFT-LCD Module: Connector DC/DC Converter LVDS Receiver Timing Controller Gamma Correction TFT-LCD 1280*(3)*1024 Pixels X-Driver IC Y-Driver IC G1024 D1 D3840 Inverter DC POWER AUO ASIC Over-Driver LVDS + 5V
document version 0.5 15/31 M190EG01 V0 4. Absolute Maximum Ratings Absolute maximum ratings of the module is as following:
4.1 Absolute Ratings of TFT LCD Module
Item Symbol Min. Max. Unit Conditions Logic/LCD Drive Voltage VDD -0.3 +6 [Volt] Note 1, 2
4.2 Absolute Ratings of Backlight Unit
Item Symbol Min. Max. Unit Conditions CCFL Current ICFL - 8 [mA] rms Note 1, 2
4.3 Absolute Ratings of Environment
Item Symbol Min. Max. Unit Conditions Operating Temperature TOP 0 +50 [ oC] Operation Humidity HOP 5 90 [%RH] Storage Temperature TST -20 +60 [ oC] Storage Humidity HST 5 90 [%RH] Note 3
document version 0.5 16/31 M190EG01 V0 Note 1: With in Ta= 25 ℃ Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard). Operating Range Storage Range
document version 0.5 17/31 M190EG01 V0 5. Electrical characteristics
5.1 TFT LCD Module
Input power specifications are as follows: Symble Parameter Min. Typ. Max. Unit Condition VDD Logic/LCD Drive Voltage 4.5 5.0 5.5 [Volt] ±10% IDD Input Current - 1.50 1.80 [A] VDD= 5.0V, All Black Pattern At 75Hz PDD VDD Power - 7.5 9.0 [Watt] VDD= 5.0V, All Black Pattern At 75Hz , Note 1 IRush Inrush Current - 2 3 [A] Note 2 Note 1: The variance of VDD power consumption is ±10%. Note 2: Measurement conditions: +5.0V +12.0V VCC 47K VR1 47K SW1 SW MAG-SPST 1 2 AO6402 G D2S 1uF/16V AO6402 G D2 S 0.01uF/25V 1uF/25V (High to Low) Control Signal (LCD Module Input) 90% 10% VDD rising time 0V 5.0V 470 us
document version 0.5 18/31 M190EG01 V0 Parameter guideline for CCFL Inverter is under stable conditions at 25 (Room Temperature):℃ Parameter Min. Typ. Max. Unit Condition CCFL Standard Current(ISCFL) 7.0 7.5 8.0 [mA] rms Note 2 CCFL Operation Current(IRCFL) 3.0 7.5 8.0 [mA] rms Note 2 CCFL Frequency(FCFL) 40 60 80 [KHz] Note 3,4 CCFL Ignition Voltage(ViCFL, Ta= 0)℃ 1690 - - [Volt] rms CCFL Ignition Voltage(ViCF, Ta= 25)℃ 1300 - - [Volt] rms Note 5 CCFL Operation Voltage (VCFL) - 653 @7.5mA 796 @3mA [Volt] rms Note 6 CCFL Power Consumption(PCFL) - 19.6 20.56 [Watt] Note 6 CCFL Life Time(LTCFL) 40,000 50,000 - [Hour] Note 7 Note 1: Typ. are AUO recommended design points. *1 All of characteristics listed are measured under the condition using the AUO test inverter. *2 In case of using an inverter other than listed, it is recommended to check the inverter carefully. Sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 In designing an inverter, it is suggested to check safety circuit very carefully. Impedance of CCFL, for instance, becomes more than 1 [M ohm] when CCFL is damaged. *4 Generally, CCFL has some amount of delay time after applying kick-off voltage. It is recommended to keep on applying kick-off voltage for 1 [Sec] until discharge. *5 Reducing CCFL current increases CCFL discharge voltage and generally increases CCFL discharge frequency. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. Note 2: CCFL standard current is measured at 25 ±2℃. Note 3: CCFL discharge frequency should be carefully determined to avoid interference between inverter and TFT LCD. Note 4: The frequency range will not affect to lamp life and reliability characteristics. Note 5: CCFL inverter should be able to give out a power that has a generating capacity of over 1,690 voltage. Lamp units need 1,690 voltage minimum for ignition. Note 6: The variance of CCFL power consumption is ±10%. Calculator value for reference (ISCFL × VCFL × 4 = PCFL)
document version 0.5 19/31 M190EG01 V0 Note 7: Definition of life: brightness becomes 50% or less than the minimum luminance value of CCFL. The typical life time of CCFL is on the condition at 7.5 mA lamp current.
document version 0.5 20/31 M190EG01 V0 6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship of the input signals and LCD pixel format. R G B R G B R G B R G B R G B R G B R G B R G B 0 1 1279 1280 1st Line 1024th Line
document version 0.5 21/31 M190EG01 V0
6.2 The Input Data Format
Note1: Normally, DE, VS, HS on EVEN channel are not used. Note2: Please follow PSWG. Note3: 8-bit in
document version 0.5 22/31 M190EG01 V0
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible . The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. PIN # SIGNAL NAME DESCRIPTION
1 RxOIN0- Negative LVDS differential data input (Odd data)
2 RxOIN0+ Positive LVDS differential data input (Odd data)
3 RxOIN1- Negative LVDS differential data input (Odd data)
4 RxOIN1+ Positive LVDS differential data input (Odd data)
5 RxOIN2- Negative LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
6 RxOIN2+ Positive LVDS differential data input (Odd data, H-Sync,V-Sync,DSPTMG)
7 VSS Power Ground
8 RxOCLKIN- Negative LVDS differential clock input (Odd clock)
9 RxOCLKIN+ Positive LVDS differential clock input (Odd clock)
10 RxOIN3- Negative LVDS differential data input (Odd data)
11 RxOIN3+ Positive LVDS differential data input (Odd data)
12 RxEIN0- Negative LVDS differential data input (Even data)
13 RxEIN0+ Positive LVDS differential data input (Even data)
14 VSS Power Ground
15 RxEIN1- Negative LVDS differential data input (Even data)
16 RxEIN1+ Positive LVDS differential data input (Even data)
17 VSS Power Ground
18 RxEIN2- Negative LVDS differential data input (Even data)
19 RxEIN2+ Positive LVDS differential data input (Even data)
20 RxECLKIN- Negative LVDS differential clock input (Even clock)
21 RxECLKIN+ Positive LVDS differential clock input (Even clock)
22 RxEIN3- Negative LVDS differential data input (Even data)
23 RxEIN3+ Positive LVDS differential data input (Even data)
24 VSS Power Ground
25 VSS Power Ground
26 NC No Connection ( for AUO test)
27 VSS Power Ground
28 VCC +5.0V Power Supply 29 VCC +5.0V Power Supply 30 VCC +5.0V Power Supply
document version 0.5 23/31 M190EG01 V0 Note1: Start from left side Note2: Input signals of odd and even clock shall be the same timing. Note3: Please follow PSWG.
6.4 Interface Timing
Basically, interface timings described here is not actual input timing of LCD module but output timing of SN75LVDS82DGG (Texas Instruments) or equivalent. Item Symbol Min Typ Max Unit Data CLK Tclk 30 54 83 MHz Period Th 720 844 1024 Tclk H-section Display Area Tdisp(h) 640 640 640 Tclk Period Tv 1035 1066 2048 Th V-section Display Area Tdisp(v) 1024 1024 1024 Th Frame Rate F 50 60 75 Hz Note : DE mode only Connector 1 30 RxOIN0- VCC
document version 0.5 24/31 M190EG01 V0
6.4.2 Timing Digram
M Invalid Data Tdisp(v) DE DE Invalid Data RGB Data Th RGB Data (Even) 39M-1 Invalid Data N Hsync M-2 Invalid Data11 M-3 Vsync Invalid Data CLK M-5 Invalid Data M-4 Tbp(h) Pixel Pixel Pixel Pixel Pixel RGB Data (Odd) Tbp(v) Tclk PixelPixelPixelPixelPixelPixelPixelPixel Pixel Pixel Pixel Pixel 4 3 Tv Tdisp(h) LineLineLineLineLineLine Tfp(v) Tfp(h) PWvs PWhs
document version 0.5 25/31 M190EG01 V0 VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Power Sequence Timing Value Parameter Min. Typ. Max. Unit T1 0.5 - 10 [ms] T2 0 - 50 [ms] T3 200 - - [ms] T4 200 - - [ms] T5 0 16 50 [ms] T6 - - 10 [ms] T7 500 - - [ms] Note: The values of the table are follow PSWG. T7 T 5T2 VALID DATA 10% 90% 10% 90% T6 Power Supply VDD LVDS Signal Backlight On
document version 0.5 26/31 M190EG01 V0 7. Connector & Pin Assignment Physical interface is described as for the connector on module.These connectors are capable of accommodating the following signals and will be following components .
7.1 TFT LCD Module
7.1.1 Connector
Connector Name / Designation Interface Connector / Interface card Manufacturer JAE or compatible Type Part Number FI-XB30SSL-HF15 Mating Housing Part Number FI-X30HL
7.1.2 Pin Assignment
Pin# Signal Name Pin# Signal Name
1 RxOIN0- 2 RxOIN0+
3 RxOIN1- 4 RxOIN1+
5 RxOIN2- 6 RxOIN2+
7 VSS 8 RxOCLKIN-
9 RxOCLKIN+ 10 RxOIN3-
11 RxOIN3+ 12 RxEIN0-
13 RxEIN0+ 14 VSS
15 RxEIN1- 16 RxEIN1+
17 VSS 18 RxEIN2-
19 RxEIN2+ 20 RxECLKIN-
21 RxECLKIN+ 22 RxEIN3-
23 RxEIN3+ 24 VSS
25 VSS 26 NC
27 VSS 28 VCC
29 VCC 30 VCC
document version 0.5 27/31 M190EG01 V0
7.2 Backlight Unit
Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation Lamp Connector / Backlight lamp Manufacturer JST Type Part Number BHSR-02VS-1 Mating Type Part Number SM02B-BHSS-1-TB Connector No. Pin No. Input Color Function
1 Hot1 Pink High Voltage
CN1 2 Cold1 Black Low Voltage
1 Hot2 Blue High Voltage Upper
CN2 2 Cold2 White Low Voltage Connector No. Pin No. Input Color Function CN3 2 Cold1 Black Low Voltage
1 Hot2 Blue High Voltage Lower
CN4 2 Cold2 White Low Voltage
document version 0.5 28/31 M190EG01 V0 8. Reliability Test Environment test conditions are listed as following table. Items Required Condition Note Temperature Humidity Bias (THB) Ta= 50, ℃ 80%RH, 300hours High Temperature Operation (HTO) Ta= 50, ℃ 50%RH, 300hours Low Temperature Operation (LTO) Ta= 0, 300hours℃ High Temperature Storage (HTS) Ta= 60, 300hours℃ Low Temperature Storage (LTS) Ta= -20, 300hours℃ Vibration Test (Non-operation) Acceleration: 1.5 G Wave: Random Frequency: 10 - 200 - 10 Hz Sweep: 30 Minutes each Axis (X, Y, Z) Shock Test (Non-operation) Acceleration: 50 G Wave: Half-sine Active Time: 20 ms Direction: ±X, ±Y, ±Z (one time for each Axis) Drop Test Height: 60 cm, package test Thermal Shock Test (TST) -20 ℃/30min, 60℃/30min, 100 cycles 1 On/Off Test On/10sec, Off/10sec, 30,000 cycles Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point. ESD (ElectroStatic Discharge) Air Discharge: ± 15KV, 150pF(330 Ω ) 1sec 8 points, 25 times/ point. Altitude Test Operation:10,000 ft Non-Operation:30,000 ft Note 1: The TFT-LCD module will not sustain damage after being subjected to 100 cycles of rapid temperature change. A cycle of rapid temperature change consists of varying the temperature from -20℃ to 6 0℃, and back again. Power is not applied during the test. After temperature cycling, the unit is placed in normal room ambient for at least 4 hours before power on. Note 2: According to EN61000-4-2 , ESD class B: Some performance degradation allowed. No data lost. Self-recoverable. No hardware failures.
document version 0.5 29/31 M190EG01 V0 9. Shipping Label The shipping label format is shown as below.
document version 0.5 30/31 M190EG01 V0 10. Mechanical Characteristic
document version 0.5 31/31 M190EG01 V0