DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 28
Technical content
Model No. LS013B4DN04 Notice Mobile Liquid Crystal Display Group SHARP CORPORATION No. LCP-1109027 Date Jan 13th 2010 The technical Literature is subject to change without any prior notice for the purpose of product improvement. Please contact Sharp or its representative before designing your product based on this literature.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE NOTICE <<Precautions>> ○ These specification sheets are the proprietary product of SHARP CORPORATION ("SHARP") and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. ○ The application examples in these specification sheets are provided to explain the representative applications of the device and are not intended to guarantee any industrial property right or other rights or license you to use them. SHARP assumes no responsibility for any problems related to any industrial property right of a third party resulting from the use of the device. ○ SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when in using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs, such as: EPersonal computers EOffice automation ETelecommunication equipment ETest and measurement equipment EIndustrial control EAudio visual and multimedia equipment EConsumer electronics The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: ETransportation control and safety equipment(i.e.,aircraft,trains,automobiles,etc.) ETraffic signals EGas leakage sensor breakers EAlarm equipment EVarious safety devices etc. ○ SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: EMilitary and space applications ENuclear power control equipment EMedical equipment for life support ○ SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specification sheets. ○ Contact and consult with a SHARP sales representative for any questions about this device.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE [For handling and system design] (1) Handle with care as glass is used in this LCD panel. Dropping or contact against hard object may cause cracks or chips. (2) Be careful to handle this LCD panel in order to avoid injury yourself by panel\`s edge as this panel is made of glass and might be a sharp edge. (3) Do not scratch the surface of the UV protection film as it is easily damaged. (4) Water droplets on the UV protection film must be wiped off immediately as they may cause color changes, or other defects if remained for a long time. (5)Do not leave the LCD panel in direct sun or under ultraviolet ray. (6) To clean LCD panel surface, wipe clean with absorbent cotton or soft cloth. If further cleaning is needed, use IPA (isopropyl alcohol) and wipe clean lightly on surface only. Do not use organic solvents as it may damage the LCD panel terminal area which uses organic material. Also, do not directly touch with finger. When the terminals cleaning are needed, those should be wiped by a soft cloth or a cotton swab without directly touching by hand. (7) Do not expose gate driver, etc. on the panel (circuit area outside panel display area) to light as it may not operate properly. Design that shields gate driver, etc. from light is required when mounting the LCD module. (8) To avoid circuit failure, do not touch panel terminal area. (9) Support for the LCD panel should be carefully designed to avoid stress that exceeds specification on glass surface. (10) When handling LCD module and assembling them into cabinets, be noted that storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent, solvent, adhesive, resin, and etc. which generate these gasses, may cause corrosion and discoloration of LCD modules. (11)To avoid picture uniformity failure, do not put a seal or an adhesive material on the panel surface. (12) Do not use chloroprene rubber as it generates chlorine gas and affects reliability in LCD panel connective area. (13) Protective film is attached to the surface of UV protection film on LCD panel to prevent scratches or other damages. Remove this protective film before use. In addition, do not attach the protective film which is removed from LCD module again. When the LCD panel which has the reattached protective film is needed to storage for a long time, the UV protection film might have a damage with picture quality failure. (14) Panel is susceptible to mechanical stress and such stress may affect the display. Place the panel on flat surface to avoid stress caused by twist, bend, etc. (15) When transporting LCD panels, secure them in LCD panel tray to avoid mechanical stress. The tray should be conductive to protect LCD panels from static charge. Material used in set or epoxy resin (amine type hardening agent) from packaging, and silicon adhesive (dealcoholized or oxime) all release gas which may affect quality of UV protection film. Do confirm compatibility with user materials. (16) As this LCD module is composed electronic circuits, it is sensitive to electrostatic discharge of 200V or more. Handle with care using cautions for the followings: z Operators Operators must wear anti-static wears to prevent electrostatic charge up to and discharge from human body.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE z Equipment and containers Process equipment such as conveyer, soldering iron, working bench and containers may possibly generate electrostatic charge up and discharge. Equipment must be grounded through 100Mohms resistance. Use ion blower. z Floor Floor plays an important role in leaking static electricity generated in human body or equipment. If the floor is made of insulated material (such as polymer or rubber material), such static electricity may charge. Proper measure should be taken to avoid static electricity charge (electrostatic earth: 100Mohms).There is a possibility that the static electricity is charged to them without leakage in case of insulating floor, so the electrostatic earth:1×10 8Ω should be made. z Humidity Humidity in work area relates to surface resistance of the persons or objects that generate electrostatics, and it can be manipulated to prevent electrostatic charge. Humidity of 40% or lower increases electrostatic earth resistance and promotes electrostatic charging. Therefore, the humidity in the work area should be kept above 40%. Specifically for film peeling process or processes that require human hands, humidity should be kept above 50% and use electricity removal blower. z Transportation/Storage Containers and styroform used in transporation and storage may charge electrostatic (from friction and peeling) or electrostatic charge from human body, etc. may cause containers and styroform to have induced charge. Proper electrostatic measure should be taken for containers and storage material.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE [For operating LCD module] (1) Do not operate the LCD panel under outside of electrical specification. Otherwise LCD panel may be damaged. (2) Do not use the LCD panel under outside of specified driving timing chart. Otherwise LCD panel may not have proper picture quality. (1) Do not operate the LCD panel under outside of electrical specification. Otherwise LCD panel may be damaged. (2) Do not use the LCD panel under outside of specified driving timing chart. Otherwise LCD panel may not have proper picture quality. (3) A still image should be displayed less than two hours, if it is necessary to display still image longer than two hour, display image data must be refreshed in order to avoid sticking image on LCD panel. (4) If LCD m odule tak es a static e lectricity, as the d isplay image which is written into pixel m emory m ight not be displayed, Data update should be executed frequently. [Precautions for Storage] (1) After opening the package, do not leave the LCD panel in direct sun or under strong ultraviolet ray. Store in dark place. (2) In tem perature lower t han s pecified r ating, liquid c rystal m aterial will c oagulate. In tem perature higher tha n specified rating, it isotropically liquifies. In either condition, the liquid crystal may not recover its original condition. Store the LCD panel in at or around room temperature as much as possible. Also, storing the LCD panel in high humidity will damage the polarizer. Store in normal room temperature as much as possible. (3) Keeping Method a. Don't keeping under the direct sunlight. b. Keeping in the tray under the dark place.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE [Other Notice] (1) Operation outside specified environmental conditions cannot be guaranteed. (2) As power supply (VDD-VSS AVDDA-VSSA) impedance is lowered during use, bus controller should be inserted near LCD module as much as possible. (3) UV protection film is applied over LCD panel surface. Liquid crystal inside LCD panel deteriorates with ultraviolet ray. The panel should not be left in direct sun or under strong ultraviolet ray for prolonged period of time even with the UV protection film. (4) Disassembling the LCD module will cause permanent damage to the module. Do not disassemble the module. (5) If LCD panel is broken, do not ingest the liquid crystal from the broken panel. If hand, leg, or clothes come in contact with liquid crystal, wash off immediately with soap. (6) ODS (specific chlorofuorocarbon, specific halon, 1-1-1 trichloroethane, carbon tetrachloride) are not used or contained in material or all production processes of this product. (7) Observe all other precautionary requirements in handling general electronic components. Discarding liquid crystal modules LCD Panel : Dispose of as glass waste. This LCD module contains no harmful substances. The liquid crystal panel contains no dangerous or harmful substances. This liquid crystal panel contains only an extremely small amount of liquid crystal (approximately 100mg) and therefore it will not leak even if the panel should break. Its median lethal dose (LD50) is greater than 2,000 mg/kg and a mutagenetic (Aims test: negative) material is used. FPC : (1) FPC bend R should be 0.45mm or greater and R should be even. In LCD panel an connective area, do not bend FPC into UV protection film side. (2)Do not hang LCD module by FPC or apply force to FPC.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE
Contents
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 1. Outline This TFT-LCD module is a reflective active matrix memory liquid crystal display module with CG silicone thin film transistor. Module outline is indicated in fig 8-1. 2. Characteristics E Reflective panel of white and black with aspect ratio of 1:1 E 1.3” screen has 96x 96 resolusion. (9216 pixels stripe array) E Display control by serial data signal communication. E Arbitrary line data renewable. E 1bit internal memory for data storage within the panel. E Thin, light-weight and compact module with monolithic technology. E Super low power consumption TFT panel. E FPC attached (Applicable connectors: Please refer to the page 21 “Recommended Connectors” 3. Mechanical Specification Table 3-1 Item Specification unit Screen size 3.4 (1.3”) cm Viewing Area 24.192 (H) × 24.192 (V) mm Dot configuration 96 (H) × 96 (V) Dot Dot pitch 0.252 (H) × 0.252 (V) mm Pixel Array Stripe Array - Outline Dimension Mass 3.6 (TYPj g Surface Hardness 3H Pencil hardness (Note) Detail dimension and tolerance are shown in fig. 8-1
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 4. Input terminal names and functions Table4-1 Terminal symbol I^O Function Remark
1 SCLK INPUT Serial clock signal
2 SI INPUT Serial data input signal
3 SCS INPUT Chip select signal
4 EXTCOMIN INPUT External COM inversion signal input (H: enable)
5 DISP INPUT Display ON/OFF signal yRemark4-2z
6 VDDA POWER Power supply (Analog)
7 VDD POWER Power supply (Digital)
8 EXTMODE INPUT COM inversion select terminal yRemark4-1z
9 VSS GND GND(Digital)
10 VSSA GND GND(Analog)
yRemark4-1zWhen it’s ”H”, EXTCOMIN signal is enable. And when it’s ”L” ,sirial input flag is enable. yRemark4-1zWhen it’s ”H”, EXTCOMIN signal is enable. And when it’s ”L” ,sirial input flag is enable. “H”mode; connect the EXTMODE toVDD, ”L” mode; connect the EXTMODE to VSS. yRemark4-2zThe display ON/OFF signal is only for display. Data in the memory will be saved at the time of ON/OFF. When it’s ”H”, data in the memory will display, when it’s ”L”, white color will diaplay and data in the memory will be saved. 4- 2jRecommended circuit;
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 5. Absolute Maximum Rating Table5-1 ( GND0V ) Item Symbol MIN. MAX. Unit Remark Analog VDDA -0.3 {3.6 V Power supply voltage Logic VDD -0.3 {3.6 V [Remark5-1] Input signal voltage(high) VDD V [Remark5-2] Input signal voltage(low) -0.3 V Strage Temperature Tstg TBD TBD ℃ [Remark5-3,4] Operation Temperature (at panel surface) Topr1 -10 {60 ℃ [Remark5-5] [Remark5-1] Applies to EXTMODE. [Remark5-2] Applies to SCLK, SI, SCS, DISP, EXTCOMIN. [Remark5-3] Do not exceed this temperature in any parts of module. [Remark5-4] Maximum wet bulb temperature is 57℃ or lower. No condensation is allowed. Cndensation will cause electeical leak and may cause the module to not meet this specification. [Remark5-5] Operating temperature is the temperature that guarantees only for the operation. For contrast, response time, and other display quality determination, use Ta{25℃.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6. Electrical characteristics 6-1) TFT LCD panel drive Table6-1 Recommended operating Condition VSS(GND)0VATa{25℃ Item symbol MIN. TYP. MAX. Unit Remark Analog VDDA {2.7 {3.0 {3.3 V Power supply Logic VDD {2.7 {3.0 {3.3 V [Remark6-1] Hi VIH VDD-0.1 VDD V Input signal voltage Lo VIL VSS VSS+0.1 V [Remark6-2] [Remark6-1] Applies to EXTMODE ”H” [Remark6-2] Applies to SCLK, SI, SCS, DISP, EXTCOMIN.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-2) Power supply sequence VDD/VDDAi5Vj GND GND DISP GND GND EXTCOMIN GND GND SCS GND ¦2 ¦2 GND Others GND ¦2 ¦2 GNDNormal operation Normal operation Normal operation Off sequenceNormal operation T2 T3 T4 T5 T6 T7 On Sequence ¦Refer to timing chart and AC timing characteristics for detail ¦1 B and C may be opposite (however, TCOM polarity inversion will not occur even with EXTCOMIN between DISP=hLh. Also, when D ISP and EX TCOMIN ar e s imultaneously s tarted up, allow 30 us or m ore bef ore SCS starts up (It may be less than 60us). ¦2 Setting value for pixel memory initialization SCS=Driving accordingly to clear pixel internal memory method (use all clear flag or write all screen white) S1=M2 (all clear flag) = “H” or write white SCLK: Nor mal Driving [ON Sequence] (1) 3V rise time (depends on IC) (2) Pixel memory initialization T2: 1V or more Initialize with M2 (all clear flag) or write all screen white (3) Release time for initialization of TCOM latch T3: 30us or more Time required to release COM related latch circuit initialization which is initializing using DISP signals (4) TCOM polarity initialization time T4: 30us or more Time required initializing TCOM polarity accordingly to EXTCOMIN input [Normal Operation] Duration of normal driving [Off Sequence] (5) Pixel memory initialization time T5: 1V or more (6) VA, VB, VCOM initialization time T6: 1V or more (7) 3V falling time (Depends on IC) [Remark] Precaustions at ehte time of power on and power off. Remark 1)When power on , VDD and VDDA are same time or VDD should be faster than the VDDA. Remark 2) When power off, VDD and VDDA are same time or VDDA shoud be faster than the VDD.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-3) Input signal characteristics Table6-3-1 VDDA={3.0VAVDD={3.0VAVSS=0VAVSSA=0VATa=25℃ Item Symbol MIN TYP MAX Unit Remark Frame frequency fSCS 1 - 60 Hz Clock frequency fSCLK 0.5 1 MHz Vertical Interval tV 16.66 - 1000 ms COM Frequency fCOM 0.5 - 30 Hz Table 6-3-2 VDDA={3.0VAVDD={3.0VAVSS=0VAVSSA=0VATa=25℃ Item Symbol MIN TYP MAX Unit Remark SCS Rising time trSCS - - 50 ns SCS Falling Time tfSCS - - 50 ns 136 - - us SCS High duration twSCSH 24 - - us SCS Low duration twSCSL 2 - - us SCS set up time tsSCS 6 - - us SCS hold time thSCS 2 - - us SI Rising time trSI - - 50 ns SI Falling time tfSI - - 50 ns SI set up time tsSI 380 *1 - - ns SI hold time thSI 440 *1 - - ns SCLK Rising time trSCLK - - 50 ns SCLK Falling time tfSCLK - - 50 ns SCLK High duration twSCLKH 450 950 - ns SCLK Low duration twSCLKL 450 950 - ns EXTCOMIN signal freequency fEXTCOMIN 1 60 Hz [Remark6-3] EXTCOMIN signal rising time trEXTCOMIN - - 50 ns EXTCOMIN signal falling time tfEXTCOMIN - - 50 ns EXTCOMIN signalHigh duration twEXTCOMINH 2 us DISP Rising time trDISP - - 50 ns DISP Folling time tfDISP - - 50 ns yRemark 6-3z EXTCOMIN frequency should be made lower than frame frequency.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 10% 90% 10% 90% 10% 90% 10% 90% 10% 90%50% 10% 90% 50% 50% 10%10% 50% 50% 50% 50% twSCSH twSCSL tfSCSthSCStrSCS tsSCS trSI tsSI thSI tfSI trSCLK tfSCLK twSCLKH twSCLKL SCS SI SCLK 10% 90% 10% 90% trEXTCOMIN 50% 50% 50% twEXTCOMINH fEXTCOMIN tfEXTCOMIN 10% 90% 10% 90% trDISP tfDISP EXTCOMIN DISP SCS, SI, SCLK signal EXTCOMIN signal DISP signal ¦SCS,SI,SCLKADISPAEXTCOMIN: 3V input voltage
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-4) Power consumption (Average) Table6-4 Ta25℃ Item Symbol MIN TYP MAX unit Remark Condition1 6 TBD uW [Remark6-4] Condition2 12 TBD uW [Remark6-4] * Measurement Condition 1 Display mode (no display data update), Common inversion fSCS=1Hz, with VDD=3VAVDDA=3VAfSCLK=0.5MHzADisplay pattern: Vertical stripe display * Measurement Condition 2 Data update mode (with display data update: 1Hz) Common inversion fSCS=1Hz with VDD=3VAVDDA=3VAfSCLK=0.5MHzADisplay pattern: Vertical stripe display yRemark 6-4 z This is value in steady condition, not the falue of peak power at the time of COM operation. Some marging for power supply is recommended. We recommend capacitor for VDD and VDDA. (If VDD and VDDA are on separate systems, we recommend capacitor for each.)
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-5) Input Signal Timing Chart 6-5-1 Data update mode (1 line) Updates data of only one specified line. (M0=”H”AM2”L”) SCS SI M0 M1 M2 DMYDMYDMYDMYDMYAG0 AG1 AG2 AG3 AG4 AG5 AG6DMY D1 D2 D3 D4 D93 D94 D95 D96 DUMMY DATA(don't care) SCLK tsSI thSI tsSCS Data writing period (96ck) Data transfer period (16ck) Mode selection period (3ck+5ckDMY) twSCLKHtwSCLKL twSCSH Gate line address period (7ck+1ckDMY) thSCS twSCSL M0: Mode flag. Set for “H”. Data update mode (Memory internal data update) When “L”, display mode (maintain memory internal data). M1: Frame inversion flag. When “H”, outputs VCOM=”H”, and when “L”, outputs VCOM=”L”. When EXTMODE=”H”, it can be “H” or “L”. M2: All clear flag. Refer to 6-5-4) All Clear Mode to execute clear. DUMMY DATA: Dummy data. It can be “H” or “L” (“L” is recommended.) ¦ Data write period Data is being stored in 1st latch block of binary driver on panel. ¦ Data transfer period Data written in 1st latch is being transferred (written) to pixel internal memory circuit. ¦For gate line address setting, refer to 6-6) Input Signal and Display. ¦M1: Frame inversion fl is enaled when EXTMODE=”L”. ¦When SCS becomes gLh, M0 and M2 are cleared.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-5-2 Data Update Mode (Multiple Lines) Updates arbitrary multiple lines data. (M0=”H”AM2”L”) SCS SI DUMMY DATA(don't care) SCLK DUMMY DATA(don't care) DUMMY DATA(don't care)D95 DMYAG6AG5AG4AG0 AG1D96 AG3 DMYAG6AG5AG4 D94 D95 D1D1 D2 D3 DMYAG6AG5DMY DMY D2AG1D4 AG0D93 D96M0 M2 DMY DMYM1 DMY D95 D96D2 D94D1 AG0 AG1 AG2 tsSI thSI tsSCS GL1 Data transfer period (96ck) GL2 Mode selection period (3ck+5ckDMY) GL(n)th line Data writing period (96ck) Data transfer period (16ck) GL(n-1)th Line thSCS twSCLKHtwSCLKL twSCSLtwSCSH twSCSH Gate line address period (7ck+1ckDMY) Data transfer period (8ck(Dymmy)+7ck(address)+1ck(Dummy)=16ck) Data transfer period (8ck(Dummy)+7ck(address)+1ck(Dummy)=16ck) M0: Mode flag. Set for “H”. Data update mode (Memory internal data update) When “L”, display mode (maintain memory internal data). M1: Frame inversion flag. When “H”, outputs VCOM=”H”, and when “L”, outputs VCOM=”L”. When EXTMODE=”H”, it can be “H” or “L”. M2: All clear flag. Refer to 6-5-4) All Clear Mode to execute clear. DUMMY DATA: Dummy data. It can be “H” or “L” (“L” is recommended.) ¦ Data write period Data is being stored in 1st latch block of binary driver on panel. ¦ Data transfer period For example, during GL2nd line data transfer period, GL 2nd line address is latched and GL1st line data is transferred from 1st latch to pixel internal memory circuit at the same time. ¦ For gate line address setting, refer to 6-6) Input Signal and Display. ¦ Input data continuously. ¦ M1: F rame inversion flag is enabled when EXTMODE=hLh. ¦ W hen SCS becomes gLh, M0 and M2 are cleared.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-5-3 Display Mode Maintains memory internal data (maintains current display). (M0=”L”AM2”L”) SCS SI DUMMY DATA(don't care) DUMMY DATA(don't care) SCLK M0 M1 M2M0 M1 M2 tsSI thSI tsSCS Mode selection period (3ck) twSCSH tV thSCS twSCSL Data transfer period (More than 13ck) M0: Mode flag. Set for “H”. Data update mode (Memory internal data update) When “L”, display mode (maintain memory internal data). M1: Frame inversion flag. When “H”, outputs VCOM=”H”, and when “L”, outputs VCOM=”L”. When EXTMODE=”H”, it can be “H” or “L”. M2: All clear flag. Refer to 6-5-4) All Clear Mode to execute clear. DUMMY DATA: Dummy data. It can be “H” or “L” (“L” is recommended.) ¦M1: Frame inversion flag is enabled when EXTMODE=hLh ¦When SCS becomes “L”, M0 and M2 are cleared.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-5-4 All Clear Mode Clears memory internal data and writes white. (M0=”L”AM2”H”) SCS SI DUMMY DATA(don't care) DUMMY DATA(don't care) SCLK M1 M2M0 M1 M2 M0 tsSI thSI tsSCS twSCSH tV thSCS twSCSL Mode selection period (3ck) Data transfer period (More than 13ck) M0: Mode flag. Set it “L”. M1: Frame inversion flag. When “H”, outputs VCOM=”H”, and when “L”, outputs VCOM=”L”. When EXTMODE=”H”, it can be “H” or “L”. M2: All clear flag. Set it “H” DUMMY DATA: Dummy data. It can be “H” or “L” (“L” is recommended.) ¦M1: Frame inversion flag is enabled when EXTMODE=”L”. ¦When SCS becomes gLh, M0 and M2 are cleared.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-5-5 COM Inversion There are two types of inputs, COM signal serial input (EXTMODE=”L”) and external COM signal input (EXTMODE=”H”). EXTMODE=“L” SCS SI COM M0 M1 M2 M0 M2M1 M2 M0 M1 fCOM ¦2 ¦2 M1FLC polarity inversion flag: If M1is "H" then VCOM="H" is output. If M1 is "L" then VCOM="L" is output. ¦1FLC inversion has been changed by M1 flag statement. ¦2FThe periods of plus polarity and minus polarity should be same length as much as possible. EXTMODE=“H” ¦1FLC inversion polarity has been set by the rising timing of EXTCOMIN in internal circuit block as COMZ signal, ¦2FThe period of EXTCOMIN should be constant. ¦3FLC inversion polarity has been set by the rising timing of EXTCOMIN in internal circuit block as COMZ signal, ¦4FThe period of EXTCOMIN should be constant.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 6-6) Input Signal and Display, Gate address(Line) Setting Data position in displaykH,Vl Display side up UP P3,L1 P2,L2 P96,L1 P96,L96 P2,L1 P1,L96 P1,L3 P1,L2 P1,L1 AG0AG1 AG2AG3 AG4AG5 AG6 L1 H L LLLL L L2 L H LLLL L L3 H H LLLL L L94 L HHH H L H L95 HHHH H L H L96 L L LLL H H
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 7. Optical characteristics Table 7-1 Ta=25℃ Item Symbol MIN. TYP. MAX. unit Remark H θ21,θ22 60 °(degree) θ11 60 °(degree) Viewing angle CR3 V θ12 60 °(degree) [Remark7-1] Contrast ratio CR. 5 10 [Remark7-2¤3] Reflecivity ratio R 50 % [Remark7-3] Rise τr 50 ms Response time Fall τd 50 ms [Remark 7-3,4] x 0.313 [Remark7-3] Panel Chromaticity White y 0.338 [Remark7-3] Optical characteristics measurement equipment. Figure 7-2 is for contrast ratio, reflectivity ratio, and panel chromaticity measurement, and figure 7-3 is for response time measurement. Both are to be conducted in a dark or room equivalent to a dark room Measurement equipment (LCD-5200) Measurement e quipment (CM-2002) Normal line Normal line LCD panel Light source -30 Light receiver Light receiver Light source Integrating sphere LCD panel Display center Display center Fig7-2 Contrast ratio, Reflection ratio, Panel chromaticity of white F ig7-3 response time
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE [Remark7-1] Defintion of Viewint Angle ¢Æ21 ¢Æ22 @ü Normal Line Uûü 6 o’clock direction [Remark7-2] Defintion of Contrast Retio Reflection intensity in white display Contrast ratio(CR) Reflection intensity in black display [Remark7-4] Respons time (Change in reflection ratio) It’s difined by the time change of optical receiver output when signal is input to display white or black Time Optical receiver output (Incremental) White BlackWhite
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 8. Module outline 8-1) Outline dimention of the 1.3” i96×96j panel with FPC type f ig.8-1 fig. 8-2 Recommended Connector SMK (Bottom Contact) FP12 Series: CFP-4610-0150F 8-2) FPC Bend Specification When bending FPC, bend where specified in Condition (1) and the bend R should be more than R specified in Condition (2). FPC is not to contact glass edge, and there should be no stress to connective area between panel and FPC. Condition (1) FPC bend recommended area: 0.8mm – 6.0mm from glass edge. Condition (2) Minimum bend R: Inner diameter R0.45 Fig.8-3 yRemark 8-1z Do not bend backward (toward UV protection film side) yRemark 8-2z Bend frequency: 3 times or less (Repeat bend condition: 180\` 0) Recommended Connector of 180 degree bent FPC SMK iContact side: upper side j FP-12 series F CF P-4510-0150F
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 9. External capacitors Fig. 9-1 External capacitor recommendation capacity value Recommended capacity value C1FDISP- VSS: rank B 0.1uF Ceramic capacitor C2FVDDA- VSS: rank B 1uF Cer amic capacitor C3FVDD- VSS: rank B 1uF Ceramic capacitor ¦Above circuit and parts are only recommendation. For actual use, please evaluate their conformity with your system and design. (Capacitor pressure resistance can be larger than resistance indicated above.)
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 10. Package 10-1) Serial num ber (Ink-jet pr int) will be in dicated on serial n umber label as indicated in F igure 1 0-1 outline d imension figure. Print structure ABC D Serial number s pecifications A Fa single figure of the year LS013B4DN04 9312AD00001FA Back side up Display side up Model number BFmonth(1,2....9,X,Y,Z) CFday DFserial numbe Fig. 10-1 Serial number print position 10-2) Forwarding form 1) Piling number of cartons : Max 12 Package quality in a carton : 800pcs 2) Storage condition E Humidity: 60%RH or lower (at 40) There should be no condensation at low temperature and high humidity. E Atmosphere: No harmful gas, such as acid or alkali, which causes severe corrosion on electronic parts and wiring, are to be detected. E Period: About 3 months E Opening the package: in order to prevent electrostatic damage to TFT modules, room humidity should be made over 50%RH and take effective measure such as use of earth when opening the package.
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 10-3) Package Fig. 10-2 Pac kage Form
SPEC No. LCP-1109027 MODEL N o. LS013B4DN04 PAGE 11. Reliability Test Conditions 11-1) Reliability test items Table11-1 Test Item Test condition Remark
1 High temperature storage test Ta=80degrees Celsius 240h
Low temperature storage test Ta=35degrees Celsius 240h High temperature and high humidity operating test Tp=40degrees Celsius/95%RH 240h
4 High temperature operating test Tp=70degrees Celsius 240h
5 Low temperature operating test Tp=-20degrees Celsius 240h
(Non operating test) Ta=-30degrees Celsius (1h) \`+80 degrees Celsius (1h) / 5 cycle
7 Electro static discharge test ±200VA200pF(0Ω) each terminai: 1 time
[Remark] Ta = Ambient temperature, Tp = Panel temperature (Evaluation method) In the standard condition, there shall be no practical problems that may affect the display function. 11-2) Panel surface stress spesification Panel surface stress spesification has been defined as a parameter “Force of stress [N]” without no picture failer. Load testingF Minimum 120[N] Test condition ) Test stracture FLCD panel with UV protection film Press point FCenter of LCD panel Press Jig Fφ10mm column Press speed F1mm^minute Support Ffixed on stage Press time F5 seconds after achivement of the press strength,then reless it.