LP6236 POWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 9

Technical content

Features

 Up to 94% efficiency  Output to Input Disconnect at Shutdown Mode  Shut-down current:<1uA  Output voltage Up to 25V  Internal Compensation, Soft-start  800KHz fixed frequency switching  High switch on current:2.0A  Available in SOT23-6/ TDFN-6 Package Typical Application Circuit Marking Information Device Marking Package Shipping LP6236B6F LPS 5XYWX SOT23-6 3K/REEL LP6236QVF LPS 5XYWX DFN-6 3K/REEL Marking indication: Y:Production year W:Production period X:Production batch 220K EN 4 SW FB 3 GND VIN 5 NC 6 LP6236B6F VIN VOUT 22uF 22uF 30K 4.7uH

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 2 of 9 Preliminary Datasheet LP6236 Functional Pin Description Package Type Pin Configurations SOT23-6 / TDFN-6 NC EN VINGND FB SW 61 GND VIN FB NC SW1 3 4 EN GND SOT23-6 TDFN-6 Pin Name Description SOT23-6 TDFN-6 1 6 SW switching pin. 2 1 GND Ground. 3 4 FB Regulation Feedback Input. Connect to an external resistive voltage divider from the output to FB to set the output voltage. 4 3 EN Regulator ON/OFF Control Input. A logic high input(V EN>1.4V) turns on the regulator. A logic low input(V EN<0.4V) puts the LP 6236 into low current shutdown mode. 5 2 VIN Power Supply pin. 6 5 NC No Connection.

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 3 of 9 Preliminary Datasheet LP6236 Function Diagram FB EN SHUTDOWN CIRCUITRY UVLO SOFT START CONTROL AND DRIVER LOGIC SLOPE COMPENSASIONOSCILLATOR OVP VIN SW GND OTP SHORT CIRCUIT COMP. Error Amp. PWM COMP. CURRENT SENSE AMP. 10μA 0.3V 0.6V Σ Absolute Maximum Ratings Note 1 Note 1. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not imp lied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Thermal Information ESD Susceptibility

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 4 of 9 Preliminary Datasheet LP6236

Electrical Characteristics

(VIN=3.3V, VOUT=5V, CIN=10uF, COUT=22uF, L=4.7uH, R1=220K, R2=30K) Parameter Condition Min Typ. Max Units Supply Voltage 2.2 6 V Output Voltage Range 2.5 25 V Supply Current(Shutdown) VEN=VOUT=0V, VSW=5V 0.05 1 uA Supply Current VEN=2V 200 uA Feedback Voltage 0.588 0.6 0.612 V Feedback Input Current VFB=0.6V 50 nA Switching Frequency 800 KHz Maximum Duty Cycle 80 90 95 % EN Input Low Voltage 0.4 V EN Input High Voltage 1.4 V Switch MOSFET Current Limit 2.0 A High-side On Resistance VOUT=3.3V 220 300 mΩ

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 5 of 9 Preliminary Datasheet LP6236 Typical Operating Characteristics Start up Waveform CH1=VEN, CH2=VOUT CH1=△VOUT，CH2=VSW @ VIN=3.7V, VOUT=5V, IOUT=1mA CH1=△VOUT，CH2=VSW @ VIN=3.7V, VOUT=5V, IOUT=500mA 20% 30% 40% 50% 60% 70% 80% 90% 100% 0 500 1000 1500 Efficiency IOUT / mA Efficiency VS. IOUT @ Different Vin with VOUT=5V Vin=3V Vin=3.3V Vin=3.5V Vin=3.7V Vin=4.2V

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 6 of 9 Preliminary Datasheet LP6236 Operation Information The LP6236 uses a fixed frequency, peak current mode boost regulator architecture to regulate voltage at the feedback pin. At the start of each oscillator cycle the MOSFET is turned on through the control circuitry. To prevent sub -harmonic oscillations at duty cycle s greater than 50 percent, a stabilizing ramp is added to the output of the current sense amplifier and the result is fed into the negative input of the PWM comparator. When this voltage equals The output voltage of the error amplifier the power MOSFET is turned off. The voltage at the output of the error amplifier is an amplified version of the difference between the 0.6V bandgap reference voltage and the feedback voltage. In this way the peak current level keeps the output in regulation. If the feedback voltage starts to drop, the output of the error amplifier increases. These results in more current to flow through the power MOSFET, thus increasing the power delivered to the output. TheLP6236 has internal soft start to limit the amount of input current at startup and to also limit the amount of overshoot on the output. Setting the Output Voltage Set the output voltage by selecting the resistive voltage divider ratio. The voltage divider drops the output voltage to the 0.6V feedback voltage. Use a 100K resistor for R2 of the voltage divider. Determine the high-side resistor R1 by the equation: VOUT = ( R1 / R2 + 1 ) x VFB Current Limitation The internal power-MOS switch current is monitored cycle-by-cycle and is limited to the value not exceed 2.0A(Typ.). When the switch current reaches the limited value, the internal power -MOS is turned off immediately until the next cycle. Keep traces at this pin as short as possible. Do not put capacitance at this pin. Inductor Selection For a better efficiency in high switching frequency converter, the inductor selection has to use a proper core material such as ferrite core to reduce the core loss and choose low ESR wire to reduce copper loss. The most important point is to prevent the core saturated when handling the maximum peak current. Using a shielded inductor can minimize radiated noise in sensitive applications. The maximum peak inductor current is the maximum input current plus the half of inductor ripple current. The calculated peak current has to be sm aller than the current limitation in the electrical characteristics. A typical setting of the inductor ripple current is 20% to 40% of the maximum input current. If the selection is 40%, the maximum peak inductor current is The minimum inductance value is derived from the following equation : Depending on the application, the recommended inductor value is between 2.2μH to 10μH.

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 7 of 9 Preliminary Datasheet LP6236 Diode Selection To achieve high efficiency, Schottky diode is good choice for low forward drop voltage and fast switching time. The output diode rating should be able to handle the maximum output voltage, average power dissipation and the pulsating diode peak current. Input Capacitor Selection For better input bypassing, low -ESR ceramic capacitors are recommended for performa nce. A 10μF input capacitor is sufficient for most applications. For a lower output power requirement application, this value can be decreased. Output Capacitor Selection For lower output voltage ripple, low -ESR ceramic capacitors are recommended. The tantalum capacitors can be used as well, but the ESR is bigger than ceramic capacitor. The output voltage ripple consists of two components: one is the pulsating output ripple current flows through the ESR, and the other is the capacitive ripple caused by charging and discharging. Layout Guideline For high frequency switching power supplies, the PCB layout is important step in system application design. In order to let IC achieve good regulation, high efficiency and stability, it is strongly recommended the power components should be placed as close as possible. The set races should be wide and short. The feedback pin and then works of feedback and compensation should keep away from the power loops, and be shielded with a ground trace or plane to prevent noise coupling.

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 8 of 9 Preliminary Datasheet LP6236 Packaging Information

LP6236 Aug.-2017 Email: marketing@lowpowersemi.com www.lowpowersemi.com Page 9 of 9 Preliminary Datasheet LP6236 TDFN-6