LM6069DFW-1 TOPWAY | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 12
Technical content
URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 1 of 12 LM6069DFW-1 LCD Module User Manual Prepared by: Chen Rili Checked by: Approved by: Date:2018-06-12 Date: Date: Rev. Descriptions Release Date
0.1 New release 2014-01-22
0.2 Update interface setting 2018-06-12
A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 2 of 12 Table of Content A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 3 of 12 1. Basic Specifications
1.1 Display Specifications
1) LCD Display Mode : STN-Blue, Negative, Transmissive 2) Display Color : Display Data = “1” : Light Gray (*1) : Display Data = “0” : Dark Blue (*2) 3) Viewing Angle : 6H 4) Driving Method : 1/65 duty, 1/9 bias 5) Backlight : While LED backlight Note: *1. Color tone may slightly change by Temperature and Driving Condition. *2. The Color is defined as the inactive / background color *3. Fine Contrast adjustment function is necessary in the application design for optimal display result
1.2 Mechanical Specifications
1) Outline Dimension : 96.0 x 38.3 x 11.0MAX (mm) (See attached Outline Drawing for details)
1.3 Block Diagram
216×64Pixels VDD IST3020 or equivalent VSS SCLK,SI /CS1, /RESET, A0 Back light BLA A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 4 of 12 2. Terminal Functions PIN NO. PIN Name I/O Descriptions Serial mode (Default) 8-bit parallel 6800 mode 8-bit parallel 8080 mode
1 VSS Supply Negative power supply,0V
2 VDD Supply Positive power supply
/CS1=L, enable access to the LCD module /CS1=H, disable access to the LCD module 4 /RESET Input Reset signal /RESET = L, Initialization is executed /RESET = H, Normal running.
5 A0 Input
A0 = H, Transferring the Display Data A0 = L, Transferring the Control Data
6 NC(R/W,/WR) Input
Not used, Leave open or pull Hi R/W=H,E=H; Data or Status read from the LCD module R/W=L,E=HL; Data or Status latch into the LCD module /WR=LH, /RD=H; Data or Instruction latch into the LCD module NC(E,/RD) Input /WR=H, /RD=L; Data or Status read form the LCD module
8 NC(DB0) I/O DB5-DB0 connect to
8-bit Data bus; Three state I/O terminal for display data or instruction data when /CS1=H, DB0~DB7=High Impedance : : I/O
13 NC(DB5) I/O
14 SCL( DB6): I/O Serial clock input
15 SI(DB7) I/O Serial data input
16 BLA Power Backlight Positive Supply
Interface setting: Setting SPI mode(Default) 6800 mode 8080 mode JP1 CLOSE CLOSE OPEN JP2 OPEN OPEN CLOSE JP3 OPEN CLOSE CLOSE JP4 CLOSE OPEN OPEN JP7～JP14 CLOSE OPEN OPEN A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 5 of 12 3. Absolute Maximum Ratings Items Symbol Min. Max. Unit Condition Supply Voltage V -0.3 DD +3.6 V VSS = 0V Input Voltage V -0.2 IN VDD V +0.2 VSS = 0V Operating Temperature T -20 OP +70 °C No Condensation Storage Temperature T -30 ST +80 °C No Condensation Cautions: Any Stresses exceeding the Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. 4. Electrical Characteristics
4.1 DC Characteristics
VSS=0V, VDD=3.3V, TOP=25°C Items Symbol MIN. TYP. MAX. Unit Condition / Application Pin Operating Voltage V 3.0 DD - 3.6 V VDD Input High Voltage V 0.85xVIH - DD V V DD /RESET, /CS1, A0, /WR, /RD, DB0~DB7 Input Low Voltage V VIL - SS 0.15xV V DD Operating Current I - DD 0.3 2.3 mA VDD
4.2 LED Backlight Circuit Characteristics
VBLK=0V, IfBLA=68mA, TOP=25°C Items Symbol MIN. TYP. MAX. Unit Applicable Pin Forward Voltage Vf - BLA 3.3 - V BLA Forward Current If - BLA 68 80 mA BLA VSS BLA A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 6 of 12
4.3 AC Characteristics
4.3.1 Serial Mode Interface
VSS=0V, VDD=3.3V, TOP=25°C Item Symbol MIN. TYP. MAX. Unit Serial Clock Period tscyc 357 - - ns Address setup time (A0) tsas 214 - - ns Address hold time (A0) tsah 214 - - ns SCL “H” pulse width tshw 143 - - ns SCL “L” pulse width tslw 143 - - ns Data setup time tsds 143 - - ns Data hold time tsdh 143 - - ns CS-SCL time tcss 214 - - ns CS-SCL time tcsh 214 - - ns Note: *1. Input signal rise/fall time should be less than 15ns . *2. CL=100pF *3.All timing is using 20% and 80% of VDD as the reference. A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 7 of 12 4.3.2 6800 Mode System Bus Timing VSS=0V, VDD=3.3V, TOP=25°C Item Symbol MIN. TYP. MAX. Unit System cycle time tcyc6 430 - - ns Address setup time (A0) taw6 10 - - ns Address hold time (A0) tah6 10 - - ns Control LOW pulse width (R/W) tewlr - - - ns Control LOW pulse width (R/W) tewlw - - - ns Control HIGH pulse width (/RD) tewhr 86 - - ns Control HIGH pulse width (R/W) tewhw 86 - - ns Data setup time tds6 58 - - ns Data hold time tdh6 22 - - ns /RD access time (*2) tacc6 - - 200 ns Output disable time (*2) toh6 7 - 143 ns Note: *1. Input signal rise/fall time should be less than 15ns . *2. CL=100pF *3.All timing is using 20% and 80% of VDD as the reference. A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 8 of 12 4.3.3 8080 Mode System Bus Timing VSS=0V, VDD=3.3V, TOP=25°C Item Symbol MIN. TYP. MAX. Unit System cycle time tcyc8 430 - - ns Address setup time (A0) taw8 10 - - ns Address hold time (A0) tah8 10 - - ns Control LOW pulse width (/RD) tcclr 86 - - ns Control LOW pulse width (/WR) tcclw 86 - - ns Control HIGH pulse width (/RD) tcchr 86 - - ns Control HIGH pulse width (/WR) tcchw 86 - - ns Data setup time tds8 58 - - ns Data hold time tdh8 22 - - ns /RD access time (*2) tacc8 - - 200 ns Output disable time (*2) tch8 7 - 143 ns Note: *1. Input signal rise/fall time should be less than 15ns . *2.All timing is using 20% and 80% of VDD as the reference.
4.4 Reset Timing
VSS=0V, VDD=3.3V, TOP=25°C Item Symbol MIN. TYP. MAX. Unit Reset time tr - - 1.5 μs Reset LOW pulse width trw 1.5 - - μs Note: *1.All timing is using 20% and 80% of VDD as the reference. A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 9 of 12 5. Function specifications
5.1 Adjusting the Display Contrast
- This LCD module equipped with latest digital contrast adjustment function. - Its display contrast could be adjusted by MCU command. (please see the command tables for details) - It is recommended to provide a contrast adjustment interface for end-user, where the best display result could meet the individual preference in mass production.
5.2 Basic Setting
To drive the LCD module correctly and provide normally display, please use the following setting - ADC = 0 (normal) - SHL select = 1 (reverse) - LCD Bias Select = 1/9 - Initial Display Line = 0 - Entire Display ON/OFF = OFF (normal) - Reverse Display ON/OFF = OFF (normal) - Set Power Control Set: voltage follower = ON, voltage converter = ON, voltage regulator = ON - Built-in OSC = ON - Display ON/OFF = ON Note: *1. These setting/commands should issue the LCD module while start up. *2. See the Display Commands section for details.
5.3 Resetting the LCD module
The LCD module should be initialized by using /RESET terminal. While turning on the VDD and VSS power supply, maintain /RES terminal at LOW level. After the power supply stabilized, release the reset terminal (/RESET=HIGH)
5.4 Display Memory Map
Page address data LCD Display (front view) Column Address 00H D7H Note: *1. ADC = 0 (normal) *2. SHL Selection = 1 (reverse) *3. Initial Display Line = 0 216x64 pixels A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 10 of 12
5.5 Display Commands
Note: *1. Do not use any other command not listed, or the system malfunction may result. *2. For the details of the Display Commands, please refer to IST3020 data sheet. A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 11 of 12
5.6 Display Commands (continue)
Note: *1. Do not use any other command not listed, or the system malfunction may result. *2. For the details of the Display Commands, please refer to IST3020 data sheet.
5.6.1 Power off the LCD Module
It recommends that enter Power Save mode before power off the LCD module.
5.6.2 Refreshing The LCD Module
It recommends that the operating modes and display contents be refreshed periodically to prevent the effect of unexpected noise. A ll data sheet.com
TOPWAY LCD Module User Manual LM6069DFW-1 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM6069DFW-1-Manual-Rev0.2 Page: 12 of 12
5.7 Design and Handling Precaution
- The LCD panel is made by glass. Any mechanical shock (eg. dropping form high place) will damage the LCD module. 2. Do not add excessive force on the surface of the display, which may cause the Display color change abnormally. 3. The polarizer on the LCD is easily get scratched. If possible, do not remove the LCD protective film until the last step of installation. 4. Never attempt to disassemble or rework the LCD module. 5. Only Clean the LCD with Isopropyl Alcohol or Ethyl Alcohol. Other solvents (eg. water) may damage the LCD. 6. When mounting the LCD module, make sure that it is free form twisting, warping and distortion. 7. Ensure to provide enough space (with cushion) between case and LCD panel to prevent external force adding on it, or it may cause damage to the LCD or degrade the display result. 8. Only hold the LCD module by its side. Never hold LCD module by add force on the heat seal or TAB. 9. Never add force to component of the LCD module. It may cause invisible damage or degrade of the reliability. 10. LCD module could be easily damaged by static electricity. Be careful to maintain an optimum anti-static work environment to protect the LCD module. 11. When peeling off the protective film from LCD, static charge may cause abnormal display pattern. It is normal and will resume to normal in a short while. 12. Take care and prevent get hurt by the LCD panel sharp edge. 13. Never operate the LCD module exceed the absolute maximum ratings. 14. Keep the signal line as short as possible to prevent noisy signal applying to LCD module. 15. Never apply signal to the LCD module without power supply. 16. IC chip (eg. TAB or COG) is sensitive to the light. Strong lighting environment could possibly cause malfunction. Light sealing structure casing is recommend. 17. LCD module reliability may be reduced by temperature shock. 18. When storing the LCD module, avoid exposure to the direct sunlight, high humidity, high temperature or low temperature. They may damage or degrade the LCD module A ll data sheet.com