LM19264ACW-Z TOPWAY | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 10
Technical content
Prepared by: Tony Checked by: Approved by: Date: 2016-07-19 Date: Date: Rev. Descriptions Release Date 0.1 Preliminary New release . (Only add a new header terminal in the LM19264ACW module) 2016-07-19 URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 1 of 10
TOPWAY LCD Module User Manual LM19264ACW-Z URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 2 of 10 Table of Content
TOPWAY LCD Module User Manual LM19264ACW-Z 1. Basic Specifications
1.1 Display Specifications
1) LCD Display Mode : FSTN, Positive, Transflective 2) Display Color : Display Data = “1” : Dark Gray (*1) : Display Data = “0” : Light Gray (*2) 3) Viewing Angle : 6 H 4) Driving Method : 1/64 duty, 1/9bias 5) Back Light : White LED backlight Note: *1. Color tone may slightly change by Temperature and Driving Condition. *2. The Color is defined as the inactive / background color
1.2 Mechanical Specifications
1) Outline Dimension : 100.0 x 60.0 x 12.5MAX (exclude Header terminal) (see attached Outline Drawing for details)
1.3 Block Diagram
RS, R/W, E, RSTB VDD, VSS BLA, BLK LED Backlight Circuit DB0 - DB7 CSB V0UT CSA Power Booster Circuit S6B0108 or equivalent S6B0108 or equivalent S6B0108 or equivalent S6B0107 or equivalent URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 3 of 10
TOPWAY LCD Module User Manual LM19264ACW-Z URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 4 of 10
1.4 Terminal Functions
No. Pin Name I/O Descriptions
1 DB7 I/O
: : :
8 DB0 I/O
Data bus; Three state I/O terminal for display data or instruction data
9 E Input
10 R/W Input
R/W = H; Data read form the LCD module, data appears at DB0 – DB7 and can be read by the host while, E = H and the device is being selected In write mode R/W = L; Data write to the LCD module, data appears at DB0 – DB7 will be written into the LCD module at E = HL and device is being selected
11 RS Input RS = H; DB0 – DB7 = Display RAM data
RS = L; DB0 – DB7 = Instruction data
12 V0 Power LCD Contrast reference
13 VDD Power Positive Power Supply
14 VSS Power Negative Power Supply, Ground (0V)
15 CSA Input
16 CSB Input
Chip selection, enable access to each section of the LCD module CSB CSA Function 0 0 Enable access to the Left Side (64 column) of the LCD module 0 1 Enable access to the Middle Section (64 column) of the LCD module 1 0 Enable access to the Right Side (64 column) of the LCD module 1 1 Disable all the access to LCD module
17 VOUT Output Power Booster output for V0
18 RSTB Input Reset signal
RSTB = L, Display off display start line register becomes 0 no command or instruction data could be accepted RSTB = H, Normal running
19 BLA Power Positive Power for LED backlight
20 BLK Power Negative Power for LED backlight
TOPWAY LCD Module User Manual LM19264ACW-Z 2. Absolute Maximum Ratings Items Symbol Min. Max. Unit Condition Supply Voltage VDD 0 7.0 V VSS = 0V Operating Temperature TOP -20 70 C No Condensation Storage Temperature TST -30 80 C No Condensation Cautions: Any Stresses exceeding the Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. 3. Electrical Characteristics
3.1 DC Characteristics
VSS=0V, VDD =5V, TOP =25C Items Symbol MIN. TYP. MAX. Unit Applicable Pin Operating Voltage VDD 4.8 5.0 5.2 V VDD Input High Voltage VIH 3.5 - VDD V Input Low Voltage VIL 0 - 0.4 V RS, R/W, E, CSA, CSB, DB0-DB7 Operating Current IDD - 5.2 15 mA VDD, VSS
3.2 LED Backlight Circuit Characteristics
BLK=0V, IfBLA=102mA, TOP =25C Items Symbol MIN. TYP. MAX. Unit Applicable Pin Forward Voltage VfBLA - 5.0 - V BLA Forward Current IfBLA - 102 120 mA BLA Cautions: Exceeding the recommended driving current could cause substantial damage to the backlight and shorten its lifetime. BLK BLA No. of LED = 6pcs URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 5 of 10
TOPWAY LCD Module User Manual LM19264ACW-Z
3.3 AC Characteristics
VSS=0V, VDD =5V, TOP =25C Item Symbol MIN. TYP. MAX. Unit E cycle time tc 1500 - - ns E high level width twh 700 - - ns E low level width twl 700 - - ns E rise time tr - - 18 ns E fall time tf - - 18 ns Address set-up time tasu 210 - - ns Address hold time tah 15 - - ns Data set-up time tdsu 300 - - ns Data delay time td - - 480 ns Data hold time (write) tdhw 15 - - ns Data hold time (read) tdhr 30 - - ns Host Write Timing Diagram Host Read Timing Diagram URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 6 of 10
TOPWAY LCD Module User Manual LM19264ACW-Z 4. Function Specifications
4.1 Basic Setting
correctly and provide normally display, please use the following setting Display start line (Z address)= 0 LCD Display = on Note: These setting/commands should issue to both controllers while start up. See the Display Control Instructions section for details.
4.2 Adjusting the LCD display contrast
A Variable-Resistor must be conne cted to the LCD module for providing a reference to V0. Adjusting the VR will result the change of LCD display contrast. The recommended value of VR is 25k to 50k VSS LCD module VOUT VR Power Supply VDD
4.3 Resetting the LCD module
The LCD module should be initialized by setting RSTB terminal at low level when turning the p ower on. When RSTB pull low, the LCD module will: - Display off - Display start line register becomes 0. (Z-address=0) While RSTB is low, no instruction can be accepted except status read. Therefore, execute other instructions after making sure that DB4=0 (clear RSTB) and DB7=0 (ready) by status read instruction. The conditions of power supply at initial power up are as follow: Item Symbol MIN. TYP. MAX. Unit Reset time trs 2.0 - - us Rise time tr - - 150 ns URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 7 of 10
TOPWAY LCD Module User Manual LM19264ACW-Z
4.4 Display Memory Map
Page (X address data LCD Display (front view) Column(Y) Address 00h 3Fh 00h 3Fh 00h 3Fh Chip Select CSA=0, CSB=0 CSA=1, CSB=0 CSA=0, CSB=1 192x64 pixels Note: 1) Display star line (Z address) = 0 2) The Display Data store separately in three drivers.
4.5 Internal Registers
There are three registers in each se ction of LCD module. Each of them could be controlled independently. Page (X) Address Register X address register designates pages of the internal display data RAM. Count function is not available. T he address should set by instruction. Column (Y) Address Counter Y address counter designates address of the internal display data RAM. It could be set by instruction and is increased by 1 automatically by read or write display data operations. Display Start Line (Z) Register Z address register indicates of display data RAM to LCD top line. It may be used for scrolling the display patt ern on the LCD. URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 8 of 10
TOPWAY LCD Module User Manual LM19264ACW-Z URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 9 of 10
4.6 Display Control Instructions
Display on/off 0 0 0 0 1 1 1 1 1 1/0 Controls the display on or off. Internal status and display data in RAM is not affected 0=off, 1=on Set Column (Y) Address 0 0 0 1 Y address (0-63) Set the Column address into the Y address counter Set Page (X) Address 0 0 1 0 1 1 1 X address (0-7) Set the Page address into the X address register Set Display Start Line (Z address) 0 0 1 1 Z address (0-63) Indicates the display data RAM displayed at the top of the screen Status Read 0 1 Busy 0 on/off Reset 0 000 Read status Busy=L, Driver ready; Busy=H, Driver busy on/off=L, Display is on; on/off=H, Display is off Reset=L, Normal Running; Reset=H, reset Write Display Data 1 0 Write data Write display data into display data RAM, After writing instruction, Y address counter increased by 1 automatically Read Display Data 1 1 Read data Read display data form the display data RAM Note: *1. For the details of the Display Control Instructions, please refer to Samsung S6B0108 handbook.
TOPWAY LCD Module User Manual LM19264ACW-Z URL: www.topwaydisplay.com www.topwaysz.com Document Name: LM19264ACW-Z-Manual-Rev0.1 Page: 10 of 10 5. Design and Handling Precaution 1. The LCD panel is made by glass. Any mechanical shock (eg. dropping form high place) will damage the LCD module. 2. Do not add excessive force on the surface of the display, which may cause the Display color change abnormally. 3. The polarizer on the LCD is easily get scratched. If possible, do not remove the LCD protective film until the last step of installation. 4. Never attempt to disassemble or rework the LCD module. 5. Only Clean the LCD with Isopropyl Alcohol or Ethyl Alcohol. Other solvents (eg. water) may damage the LCD. 6. When mounting the LCD module, make sure that it is free form twisting, warping and distortion. 7. Ensure to provide enough space (with cushion) between case and LCD panel to prevent external force adding on it, or it may cause damage to the LCD or degrade the display result. 8. Only hold the LCD module by its side. Never hold LCD module by add force on the heat seal or TAB. 9. Never add force to component of the LCD module. It may cause invisible damage or degrade of the reliability. 10. LCD module could be easily damaged by static electricity. Be careful to maintain an optimum anti-static work environment to protect the LCD module. 11. When peeling off the protective film from LCD, static charge may cause abnormal display pattern. It is normal and will resume to normal in a short while. 12. Take care and prevent get hurt by the LCD panel sharp edge. 13. Never operate the LCD module exceed the absolute maximum ratings. 14. Keep the signal line as short as possible to prevent noisy signal applying to LCD module. 15. Never apply signal to the LCD module without power supply. 16. IC chip (eg. TAB or COG) is sensitive to the light. Strong lighting environment could possibly cause malfunction. Light sealing structure casing is recommend. 17. LCD module reliability may be reduced by temperature shock. 18. When storing the LCD module, avoid exposure to the direct sunlight, high humidity, high temperature or low temperature. They may damage or degrade the LCD module