L813PW

L813PW SUPERWORLD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 10

Technical content

(a) (c) (b) (e) (d) 1. PART NO. EXPRESSION : (b) Type code (c) Inductance code : 1R0 = 1.0uH (a) Series code 2. CONFIGURATION & DIMENSIONS : 13.5 Max. A' A B' 4. MATERIALS : SUPERWORLD ELECTRONICS (S) PTE LTD (a) Core (b) Wire (c) Terminal a 3. SCHEMATIC : (d) Tolerance code : M = ±20% (e) F : Lead Free 5. FEATURES : b) Frequency up to 5MHz a) Shielded Construction L813PW SERIES b c PG. 1 NOTE : Specifications subject to change without notice. Please check our website for latest information. 15.01.2008 PCB Pattern H G 12.7±0.3 BC ' C 5.2 Max. 5.0 Max. D E C B SWORLD R47 A 2.5±0.5 D EGHL Unit:m/m L 13.9 Max. 12.7±0.3 HIGH CURRENT MOLDED POWER INDUCTORS

SUPERWORLD ELECTRONICS (S) PTE LTD 7. ELECTRICAL CHARACTERISTICS : L813PW SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 2 15.01.2008 h) Part Temperature (Ambient+Temp. Rise) : Should not exceed 125°C under worst case operating conditions. g) Saturation Current (Isat) : Will cause L to drop approximately 20% typ. a) Test Freq. : 100KHz/1.0VDC; Q : 100KHz/1.0VDC f) Heat Rated Current (Irms) : Will cause the coil temp. rise approximately ǻT=40°C without core loss. b) Ambient Temp. : 20°C e) Humidity Range : 50 ~ 60% RH c) Operating Temp. : -55°C to +125°C d) Storage Temp. : -55°C to +125°C 6. GENERAL SPECIFICATION : 9.232153.30L813PW-3R3MF L813PW-6R8MF L813PW-4R7MF L813PW-100MF 6.80 10.00 4.70 18.521 16 25.5 27 15.0 ( µH ) Inductance L ±20% @ 0 Adc L813PW-2R2MF L813PW-R68MF L813PW-1R0MF L813PW-1R5MF L813PW-R47MF 1.00 1.50 2.20 0.47 0.68 Part No. 2.550 4.1 5.5 1.3 1.7 Typ. ( A ) Irms Typ. ( A ) Isat DCR Max. ( mȍ ) Min. Q HIGH CURRENT MOLDED POWER INDUCTORS

SUPERWORLD ELECTRONICS (S) PTE LTD L813PW SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 3 15.01.2008 8. CHARACTERISTICS CURVES : INDUCTANCE VS. FREQUENCY Q VS. FREQUENCY INDUCTANCE VS. DC CURRENT TEMP. RISE VS. DC CURRENT HIGH CURRENT MOLDED POWER INDUCTORS

SUPERWORLD ELECTRONICS (S) PTE LTD L813PW SERIES NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 4 15.01.2008 8. CHARACTERISTICS CURVES : 0 1 32 63 95 26 5 DC CURRENT(A) 0.5 0.1 0.2 0.3 0.4 INDUCTANCE (uH) 100 TE MP . RISE(oC) S MPI1205PW-R47L813PW-R47MF 0 9 18 27 36 45 54 DC CURRENT(A) 0.8 0.16 0.32 0.48 0.64INDUCTANCE (uH) 100 TE MP . RISE(oC) SMPI1205PW-R68L813PW-R68MF 0 1 02 03 04 05 0 DC CURRENT(A) 0.6 1.2 0.2 0.4 0.8 INDUCTANCE (uH) 100 TEMP. RISE( oC) SMPI1205PW-1R0L813PW-1R0MF 0 1 02 03 04 05 0 DC CURRENT(A) 0. 6 1. 2 1. 8 0. 3 0. 9 1. 5 INDUCTANCE (uH) 100 TEMP. RISE(oC) SMPI1205PW-1R5L813PW-1R5MF 0 8 16 24 32 DC CURRENT(A) 0.5 1.5 2.5 INDUCTANCE (uH) 100 TEMP. RISE(oC) S MPI1205PW-2R2L813PW-2R2MF 0 8 16 24 32 DC CURRENT(A) 0.8 1.6 2.4 3.2 INDUCTANCE (uH) 10 0 TEMP. RISE( oC) SM PI 12 05 PW-3R 3L813PW-3R3MF HIGH CURRENT MOLDED POWER INDUCTORS

SUPERWORLD ELECTRONICS (S) PTE LTD NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 5 15.01.2008 L813PW SERIES 8. CHARACTERISTICS CURVES : 09 1 8 2 7 DC CURRENT(A) INDUCTANCE (uH) 100 TEMP. RISE( oC) SMPI1205PW-4R7L813PW-4R7MF 0 3 6 9 1 21 51 82 1 DC CURRENT(A) INDUCTANCE (uH) 100 TE MP . RISE(oC) SMPI1205PW-6R8L813PW-6R8MF 0 4 8 12 16 DC CURRENT(A) INDUCTANCE (uH) 100 TEMP. RISE(oC) SMPI1205PW-100L813PW-100MF HIGH CURRENT MOLDED POWER INDUCTORS

NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD PG. 6 15.01.2008 L813PW SERIES 9. CORE LOSS : 500KHz 100KHz 100KHz and 500KHz 0 200 400 600 800 1000 gauss 10000 20000 30000 40000 KW/m3 100KHZ 500KHZ KW / m3 gauss material gauss loss 100 - 266 200 - 1,234 300 351.7 2,932 400 665.9 5,195 500 1,039 8,336 600 1,471 12,025 700 1,923 15,715 800 2,537 20,444 900 3,148 25,429 1000 3,902 31,002 100KHz 500KHz 200 400 600 800 1000 gauss 1000 2000 3000 4000 KW/m3KW / m3 gauss material gauss loss 300 351.7 400 665.9 500 1,039 600 1,471 700 1,923 800 2,537 900 3,148 1000 3,902 100KHz 0 200 400 600 800 1000 gauss 10000 20000 30000 40000 KW/m3KW / m3 gauss HIGH CURRENT MOLDED POWER INDUCTORS

SUPERWORLD ELECTRONICS (S) PTE LTD NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 7 15.01.2008 L813PW SERIES 10. RELIABILITY AND TEST CONDITION : LCR meter. Directions & times : X, Y, Z directions for 2 hours. A period of 2 hours in each of 3 mutually perpendicular Irms(A) will cause the coil temperature rise approximately ǻT=40°C without core loss CH16502, Agilent33420A Micro-Ohm Meter. Isat(A) will cause Lo to drop approximately 20% typical 2. Temperature measured by digital surface thermometer Times (min.) 30±3 Within 3 Within 3 30±3 Measure at room temperature after placing for 2 to 3 hrs. Measure at room temperature after placing for 2 to 3 hrs. Measure at room temperature after placing for 2 to 3 hrs. Measure at room temperature after placing for 2 to 3 hrs. 1. Appearance : No damage Temperature : 40±5°CHumidity Resistance Appearance : Cracking, shipping and any other defects harmful to the characteristics should not 2. Inductance : Within ±20% of initial value. No disconnection or short circuit. be allowed. Random Vibration Test directions (Total 6 hours). Amplitude : 1.52mm Frequency : 10-55-10Hz for 1 min. Humidity : 90% to 95% Applied Current : Rated Curent Time : 500±12 hours 1. Appearance : No damage 2. Inductance : Within ±20% of initial value. No disconnection or short circuit.Thermal Shock Low Temperature Life Test 1- 5 5 ± 3 Total : 5 cycles +125±3 Room Temperature Room Temperature Step Time : 500±12 hours Temperature : -55±5°C Conditions of 1 cycle. Temperature (°C) 4±1 seconds seconds Preheating 2. Inductance change : Within ±20% 1. Appearance : No significant abnormality seconds Reliability Test Life Test High Temperature 150°C Solder Heat Resistance 260°C 150°C Dip Time : 10±0.5sec. 10±0.5 seconds Time : 500±12 hours Temperature : 125±5°C Flux for lead free : rosin Solder Temperature : 260±5°C Solder : Sn99.95-Cu0.05 Preheat : 150°C, 60sec. Natural cooling Dipping Preheating More than 90% of the terminal electrode should be covered with solder. Saturation Current (Isat) Mechanical Performance Test Solderability Test 245°C Heat Rated Current (Irms) DCR Dip Time : 4±1sec. Solder Temperature : 245±5°C Flux for lead free : rosin Preheat : 150°C, 60sec. Solder : Sn99.95-Cu0.05 Natural cooling Dipping 1. Applied the allowed DC current TEST CONDITION HP4284A, CH11025, CH3302, CH1320, CH1320SRefer to standard electrical characteristics list PERFORMANCE Electrical Characteristics Test ITEM Inductance HIGH CURRENT MOLDED POWER INDUCTORS

SUPERWORLD ELECTRONICS (S) PTE LTD NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 9 15.01.2008 L813PW SERIES 12. PACKAGING INFORMATION : Bo Ko 1.75±0.1 Bo(mm) 13.9±0.1 12-3. Packaging Quantity

0.15 MIN

Series Ao(mm) 13.5±0.1 11.5±0.05 F(mm) Ao P(mm) 16.0±0.1 Ko(mm) 5.5±0.1 W(mm) 24.0±0.3 P 0.35±0.05 t(mm) F W 12-2 Tape Dimension 24.0±0.5 A(mm) 13" x 24mm Type 100±2.0 B(mm) D D(mm) 13.5±0.5 330 C(mm) EMBOSSED CARRIER B A COVER TAPE 12-1. Reel Dimension L813PW 4000 1000 Carton Chip / Reel Inner Box Size 500 2.0±0.5 ØC HIGH CURRENT MOLDED POWER INDUCTORS

SUPERWORLD ELECTRONICS (S) PTE LTD NOTE : Specifications subject to change without notice. Please check our website for latest information. PG. 10 15.01.2008 L813PW SERIES 12-4. Tearing Off Force The force for tearing off cover tape is 15 to 60 grams in the arrow direction under the following conditions. a) Products should be handled with care to avoid damage or contamination from perspiration and skin oils. 1. Storage Conditions : To maintain the solderabililty of terminal electrodes : a) Temperature and humidity conditions : Less than 30°C and 70% RH. b) Recommended products should be used within 6 months from the time of delivery. c) The packaging material should be kept where no chlorine or sulfur exists in the air. b) The use of tweezers or vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. 2. Transportation : Application Notice Top cover tape F Base tape 165° to 180° Room Temp. (°C) 5~35 Room Humidity (%) 45~85 Tearing Speed (mm/min) 300 Room atm (hPa) 860~1060 HIGH CURRENT MOLDED POWER INDUCTORS