I2360SYI

ISD2360 NUVOTON | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 33

Technical content

• 1 - Publication Release Date: 10/22/2012 Revision 1.0 ISD2360 Digital ChipCorder with Embedded Flash 3-Channel Audio Playback

• 2 - Publication Release Date: 10/22/2012 Revision 1.0 TABLE OF CONTENTS

• 3 - Publication Release Date: 10/22/2012 Revision 1.0

• 4 - Publication Release Date: 10/22/2012 Revision 1.0

1 GENERAL DESCRIPTION

The ISD2360 is a 3-channel digital ChipCorder® providing single -chip storage and playback of high quality audio. The device features digital de-compression, comprehensive memory management, flash storage, integrated audio signal path with up to 3 channel concurrent playback and Class D speaker driver capable of delivering power of 0.95W . This family utilizes flash memory to provide non -volatile audio playback with duration up to 64 seconds (based on 8kHz/4bit ADPCM compression) for a single- chip audio playback solution. The ISD2360 can be controlled and programmed through an SPI serial interface or operated stand - alone by triggers applied to the device’s six GPIO pins. The ISD2360 requires no external clock sources or components except a speaker to deliver quality audio prompts or sound effects to enhance user interfaces. In addition the part can provide non -volatile flash storage in 1Kbyte sectors eliminating the need for additional serial EEPROM/Flash devices. Compared to previous ChipCorder series, this device provides higher sampling frequencies, improved SNR, lower power, fast programming time and integrated program verification.

2 FEATURES

 Duration o ISD2360 – 64 seconds based on 8kHz/4bit ADPCM in 2Mbit of flash storage (256KB)  Audio Management o Store pre-recorded audio (Voice Prompts) using high quality digital compression o Use simple index based command for playback – no address needed. o Execute pre-programmed macro scripts (Voice Macros) designed to control the configuration of the device and playback Voice Prompts sequences.  Path and playback Control o Up to 3 channel audio streaming can be mixed and played back concurrently o Each channel has independent counter which enables user micro-management on VM execution o Mask Jump allows branch execution depending on internal register or external GPIO pin status  Control o Serial SPI interface for microprocessor control and programming. o Stand-alone control where customized Voice Macro scripts are assigned to GPIO trigger pins.  Sample Rate o 7 sampling frequencies 4, 5.3, 6.4, 8, 12.8, 16 and 32 kHz are available. o Each Voice Prompt can have optimal sample rate.  Compression Algorithms o µ-Law: 6, 7 or 8 bits per sample o Differential µ-Law: 6, 7 or 8 bits per sample o PCM: 8, 10 or 12 bits per sample o Enhanced ADPCM: 2, 3, 4 or 5 bits per sample o Variable-bit-rate optimized compression. This allows best possible compression given a metric of SNR and background noise levels.  Oscillator o Internal oscillator with internal reference: factory trimmed to ±1% deviation at room temperature.

• 5 - Publication Release Date: 10/22/2012 Revision 1.0  Output o PWM: Class D speaker driver to direct drive an 8Ω speaker or buzzer. o Delivers 400mW at 3V supply. o Delivers 1W at 5V supply  I/Os o SPI interface: MISO, MOSI, SCLK, SSB for commands and digital audio data o 6 general purpose I/O pins multiplexed with SPI interface.  Flash Storage o 2Mbit of storage for combined audio/data. o Fast programming time (20µs/byte) o Erase sector size 1Kbyte, sector erase time 2ms. o Integrated memory checksum calculation for fast verification. o Endurance >100K cycles. Retention > 10 years  Operating Voltage: 2.4-5.5V  Package: o Green, QFN32  Temperature Options: o Industrial: -40C to 85C

• 6 - Publication Release Date: 10/22/2012 Revision 1.0

3 BLOCK DIAGRAM

SCLK/GPIO(1) MISO/GPIO(2) INTB/GPIO(3) MOSI/GPIO(0) GPIO(5) SSB RDY/BSYB/GPIO(4) De-Compression De-Compression De-Compression Memory management and Command Interpreter Ch3 Memory management and Command Interpreter Ch1 Memory management and Command Interpreter Ch2 SP- Figure 3-1 ISD2360 Block Diagram

• 7 - Publication Release Date: 10/22/2012 Revision 1.0

4 PINOUT CONFIGURATION

Figure 4-1 ISD2360 32-Lead QFN Pin Configuration. Figure 4-2 ISD2360 16-Lead SOP Pin Configuration.

• 8 - Publication Release Date: 10/22/2012 Revision 1.0

5 PIN DESCRIPTION – QFN32

1 NC This pin should be left unconnected. 2 NC This pin should be left unconnected.

3 MOSI /

I Master-Out-Slave-In. Serial input to the ISD2360 from the host. Can be configured as a general purpose I/O pin. 4 VSSD Digital Ground. 5 NC This pin should be left unconnected. 6 NC This pin should be left unconnected. 7 NC This pin should be left unconnected. 8 NC This pin should be left unconnected. 9 NC This pin should be left unconnected. 10 VCCD_PWM I Digital Power for the PWM Driver. 11 SPK+ O PWM driver positive output. This SPK+ output, together with SPK- pin, provide a differential output to drive 8Ω speaker or buzzer. During power down this pin is in tri-state. 12 VSSD_PWM I Digital Ground for the PWM Driver. 13 VSSD_PWM I Digital Ground for the PWM Driver. 14 SPK- O PWM driver negative output. This SPK- output, together with SPK+ pin, provides a differential output to drive 8Ω speaker or buzzer. During power down this pin is tri-state. 15 VCCD_PWM I Digital Power for the PWM Driver. 16 NC This pin should be left unconnected. 17 NC This pin should be left unconnected. 18 NC This pin should be left unconnected. 19 NC This pin should be left unconnected. 20 NC This pin should be left unconnected.

21 INTB /

O Active low interrupt request pin. This pin is an open-drain output. Can be configured as a general purpose I/O pin.

22 RDY/BSYB /

O An output pin to report the status of data transfer on the SPI interface. “High” indicates that ISD2360 is ready to accept new SPI commands or data. Can be configured as a general purpose I/O pin. 23 NC This pin should be left unconnected.

• 9 - Publication Release Date: 10/22/2012 Revision 1.0 Pin Number Pin Name I/O Function 24 NC This pin should be left unconnected. 25 NC This pin should be left unconnected. 26 VCCD I Digital Power.

27 GPIO5 I/O General purpose I/O pin

28 NC This pin should be left unconnected.

29 MISO /

O Master-In-Slave-Out. Serial output from the ISD2360 to the host. This pin is in tri-state when SSB=1. Can be configured as a general purpose I/O pin. 30 SCLK / GPI1 I Serial Clock input to the ISD2360 from the host. Can be configured as a general purpose input pin. 31 SSB I Slave Select input to the ISD2360 from the host. When SSB is low device is selected and responds to commands on the SPI interface. When asserted, GPIO0/1/2 automatically configure to MOSI/SCLK and MISO respectively. SSB has an internal pull-up to Vccd. 32 NC This pin should be left unconnected.

• 10 - Publication Release Date: 10/22/2012 Revision 1.0

6 DEVICE OPERATION

Playback of audio stored on the ISD2360 can be accomplished by either sending SPI commands via the serial interface or triggered by signal edges applied to GPIO pins. The device is programmed via the SPI interface either in-system or utilizing commercially available gang programmers.

6.1 AUDIO STORAGE

The audio compression and customization of the ISD2360 is rapidly achieved with the supplied ISD2360VPE or Voice Prompt Editor. This software tool allows the developer to take audio clips in standard wave file format and re-sample and compress them for download to the ISD2360. Audio is stored in the ISD2360 as series of Voice Prompts: these units of audio can be of any length – the compression and sample rate of each Voice Prompt can be individually selected. A powerful feature of the ISD2360 is presence of a scripting ability Voice Macros . A Voice Macro can contain commands to play individual Voice Prompts and configure the ISD2360. A Voice Macro can be associated with a GPIO pin such that it is triggered by a transition on that pin. In this way stand -alone systems can be developed without the need for micro -controller interaction. Voice Macros can also be executed via the SPI command interface. Both Voice Pro mpts and Voice Macros are addressed via a simple sequential index address, no absolute memory address is required, thus audio source material or voice macro function can be updated (or changed for multi -language implementation) without the need to update microcontroller code.

6.2 DEVICE CONFIGURATION

The ISD2360 is configured by writing to a set of configuration registers. This can be accomplished either by sending configuration via the serial SPI interface or executing Voice Macros containing configuration commands. Most configuration registers are reset to their default values when the device is powered down to ensure lowest possible standby current. Exceptions to this are registers that control the configuration of GPIO pi ns and Jump registers that contain the Voice Macro index to execute for GPIO triggers. Configuration registers may be initialized automatically in customizable Voice Macros that are executed on a power-on reset or power-up condition.

6.3 GPIO CONFIGURATION

The six GPIO pins of the ISD2360 can be configured for a variety of purposes. Each pin can be configured to trigger a Voice Macro function. Each pin also has an alternate function allowing the pins to be configured as SPI, interrupt or oscillator reference pins. DOUT OE DIN PIN PE PS Logic Figure 6-1 GPIO Structure

• 11 - Publication Release Date: 10/22/2012 Revision 1.0 The structure of the GPIO pads is shown in Figure 6-1. Configuration registers allow the user to control pull -up and pull down resistors, enable the pin as an output or set the output value. See ISD2360 Design Guide for details on the configuration options.

6.4 OSCILLATOR AND SAMPLE RATES

The ISD2360 has an internal oscillator trimmed at manufacturing that requires no external components to operate. This oscillator provides an internal clock source that operates the ISD2360 at a maximum audio sample rate of 32kHz. The sample rates available for audio storage at this maximum sample rate are shown in Table 6-1. The sample ra te is selected during compression using the ISD2360 Voice Prompt Editor software. Table 6-1 Available Sample Rates. SR[2:0] Ratio to Sample Rate (kHz) 0 8 4 1 6 5.44 2 5 6.4 3 4 8 4 2.5 12.8 5 2 16 6 1 32

7 MEMORY FORMAT

The memory of the ISD2360 consists of byte addressable flash memory that is erasable in 1Kbyte sectors. Erased memory has a value of 0xFF. Writing to the memory allows host to change bits from erased ‘1’ state to programmed ‘0’ state. The memory of the ISD2360 is organized into four distinct regions as shown in Figure 7-1. The four regions are: 1. Configuration and Index Table : The first region of memory contains configuration data f or the device and the index table that points to the Voice Prompt and Voice Macro data. The ISD2360VPE creates this section for download to the device. 2. Voice Macros: This section contains the script code of all the projects Voice Macros. 3. Voice Prompts: This section contains the compressed audio data for all Voice Prompts. 4. User Data : An optional section containing m emory sectors allocated by the developer for generic use by the host controller.

• 12 - Publication Release Date: 10/22/2012 Revision 1.0 Voice Prompts Configuration and Index Table PMP Sector Address Byte Address 1400h 2800h 3C00h 61800h 8020000h User Data 7F1FC00h Voice Macros Figure 7-1 ISD2360 Memory Organization

7.1.1 Voice Prompts

Voice prompts are pre -recorded audio of any length, from short words, phrases or sound effects to long passages of music. These Voice Prompts can be played back in any order as determined by the application. A Voice Prompt consists of two components: 1. An index entry in the Index Table pointing to the pre-recorded audio. 2. Compressed pre-recorded audio data. A Voice Prompt is addressed using its index number to locate and play the pre -recorded audio. This address free approach allows users to easily manage the pre -recorded audio without the need to update the code on the host controller. In addition, the users can store a multitude of pre -recorded audio without the overhead of maintaining a com plicated lookup table. To assist customers in creating the Voice Prompts, ISD2360 Voice Prompt Editor and writer are available for development purposes.

7.1.2 Voice Macros

Voice Macros are a script that allows users to customize their own play patterns such as play Voice Prompts, insert silence, power-down the device and configure the signal path, including volume control. Voice Macros are executed using a single SPI command and are accessed using the same index structure as Voice Prompts. This means that a Voi ce Macro (or Voice Prompt) can be updated on the ISD2360 without the need to update code on the host micro - controller since absolute addresses are not needed. The following locations have been reserved for special Voice Macros: Index 0: Power-On Initialization (POI)

• 13 - Publication Release Date: 10/22/2012 Revision 1.0 Index 1: Power-Up (PU) Index 2: GPIO-Wakeup (WAKEUP) These Voice Macros allow the users to customize the ISD2360 power-on, power-up and GPIO wake-up procedures and are executed automatically when utilized. If these Voice Macros are not used device will perform default operations on these events. An example to illustrate the usage of the PU Voice Macro is:  WR_CFG(VOLC, 0x0C) ; Set VOLC to 0x0C  WR_CFG(REG2, 0x44) ; Set REG2 to 0x44  WR_CFG (REG_GPIO_AF1 ,0xFF) ; Set REG_GPIO_AF1 to 0xFF  WR_CFG (REG_GPIO_AF0 ,0x10) ; Set REG_GPIO_AF0 to 0x10  FINISH ; Exit Voice Macro The above PU Voice Macro will perform the following:  Choose Volume Control for -3dB level.  Configure and power up the signal path to decode compressed audio to speaker d river.  Set up all GPIOs except GPIO4 for Falling edge trigger and set GPIO4 for both falling and rising edge trigger. The following is the complete list of the command available for use in Voice Macros:  WR_CFG_REG(reg n) – Set configuration register reg to value n.  PWR_DN – Power down the ISD2360.  PLAY_VP(i) – Play Voice Prompt index i.  PLAY_VP@(Rn) – Indirect Play Voice Prompt of index in register Rn  PLAY_VP_LP(i,cnt) – Loop Play Voice Prompt index i, cnt times.  PLAY_VP_LP@(Rn,cnt) – Indirect Loop Play Voice Prompt index in Rn, cnt times.  EXE_VM(i) – Execute Voice Macro index i.  EXE_VM@(Rn) – Indirect Execute Voice Macro index in register Rn  PLAY_SIL(n) – Play silence for n units. A unit is 32ms at master sampling rate of 32 kHz.  WAIT_INT – Wait until current play command finishes before executing next macro instruction.  FINISH – Finish the voice macro and exit. These commands are equivalent to the commands available via the SPI interface and are described in Section Error! Reference source not found..

7.1.3 User Data

User Data consists of 1KByte multiples of erasable sectors allocated by the user. This can be used as generic non -volatile storage by the host application. The developer has the freedom not to allocate or reserve any m emory sectors. A software tool, the ISD2360 Voice Prompt Editor is available to assist customers in allocating such memory.

7.2 MEMORY CONTENTS PROTECTION

• 14 - Publication Release Date: 10/22/2012 Revision 1.0 Under certain circumstances, it is desirable to protect portions of the internal memory from write/erase or interrogation (read). The ISD2360 provides a method to achieve this by setting a protection memory pointer (PMP) that allows the users to protect memory for an address range from the beginning of memory to this sector containing the PMP pointer . The type of protection is set by three bits in the memory header byte. Memory protection is activated on power -up of the chip. Therefore, each time the user changes the setting of memory protection, the new setting will not be effective until the chip is rese t.

8 SPI INTERFACE

This is a standard four -wire serial interface used for communication between ISD2360 and the host. It consists of an active low slave-select (SSB), a serial clock (SCLK), a data input (Master Out Slave In - MOSI), and a data output (Maste r In Slave Out - MISO). In addition, for some transactions requiring data flow control, a RDY/BSYB signal (pin) is available. The ISD2360 supports SPI mode 3: (1) SCLK must be high when SPI bus is inactive, and (2) data is sampled at SCLK rising edge. A SPI transaction begins on the falling edge of SSB and its waveform is illustrated below: 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SSB SCLK MISO MOSI XC7 C6 C5X C4 C3 C2 C1 C0 S7 S6 S5 S4 S3 S2 S1 S0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 Z X Figure 8-1 SPI Data Transaction. A transaction begins with sending a command byte (C7 -C0) with the most significant bit (MSB – C7) sent in first. During the byte transmission, the status (S7 -S0) of the device is sent out via the MISO pin. After the byte transmission, depending upon the command sent, one or more bytes of data will be sent via the MISO pin. RDY/BSYB pin is used to handshake data into or out of the device. Upon completion of a byte transmission, RDY/BSYB pin could change its state after the rising edge of the SCLK if the built -in 32- byte data buffer is either full or empty. At t his point, SCLK must remain high until RDY/BSYB pin returns to high, indicating that the ISD2360 is ready for the next data transmission. See below for timing diagram.

• 15 - Publication Release Date: 10/22/2012 Revision 1.0 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SSB SCLK MISO MOSI XC7 C6 C5X C4 C3 C2 C1 C0 PD RDY INT FULL X VG BSY BUF FUL CMD BSY PD RDY INT FULL X VG BSY BUF FUL CMD BSY D7 D6 D5 D4 D3 D2 D1 D0 Z X RDY/BSYB BRT / =1 =1 Figure 8-2 RDY/BSYB Timing for SPI Writing Transactions. If the SCLK does not remain high, RDY bit of the status register will be set to zero and be reported via the MISO pin so the host can take the necessary actions (i.e., terminate S PI transmission and re - transmit the data when the RDY/BSYB pin returns to high). For commands (i.e., DIG_READ, SPI_ PCM_READ) that read data from the ISD2360 device, MISO is used to read the data; therefore, the host must monitor the status via the RDY/B SYB pin and take the necessary actions. The INT pin will go low to indicate (1) data overrun/overflow when sending data to the ISD2360; or (2) invalid data from ISD2360. See Figure 8-3 for the timing diagram. To avoid RDY/BSYB polling for digital operations the following conditions must be met:  Ensure device is idle (CMD_BSY=0 in status) before operation.  Digital Write: Send 32 bytes of data or less in a digital write transaction or ensure that there is a 24µs period between each byte sent where SCLK is held high.  Digital Read: Ensure a 2µs period between last address byte of digital read command and first data byte where SCLK is held high.

• 16 - Publication Release Date: 10/22/2012 Revision 1.0 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SSB SCLK MISO MOSI XC7 C6 C5X C4 C3 C2 C1 C0 PD RDY INT FULL X VG BSY BUF FUL CMD BSY PD RDY INT FULL X VG BSY BUF FUL CMD BSY D7 D6 D5 D4 D3 D2 D1 D0 Z X RDY/BSYB BRT / =1 =0 INT Fi gure 8-3 SPI Transaction Ignoring RDY/BSYB

9 SIGNAL PATH

The signal path performs filtering, sample rate conversion, volume control and decompression. A block diagram of the signal path is shown in Figure 9-1. The PWM driver output pins SPK- and SPK+ provide a differential output to drive an 8Ω speaker or buzzer. During power down these pins are in tri- state. Pre-compressed a udio transfers from memory or SPI interface through the de-compressor block to PWM driver or SPI out. The audio level is adjustable via VOLC before going out on to the PWM driver path. The possible path combinations are: MEMORY → DECOMPRESS → SPKR (Playback to speaker) MEMORY → DECOMPRESS → SPI_OUT (SPI playback) SPI_IN → DECOMPRESS → SPKR (SPI decode to speaker) For example to playback audio to speaker, e nable decompression and PWM (write 0x44 to register 0x02) then send a PLAY_VP command to play audio.

• 17 - Publication Release Date: 10/22/2012 Revision 1.0 Figure 9-1 ISD2360 Signal Path

10 GPIO VOICE MACRO TRIGGERS

The ISD2360 Voice Macro capability and GPIO flexibility allows the user to configure the device to operate independently of the SPI interface or host micro-controller. GPIO triggering utilizes the Jump registers R0 through R6. When a GPIO trigger event occurs the ISD2360 executes the Voice Macro whose index is stored in the corresponding Jump register: that is GPIO0 will execute the VM whose index is stored in R0, GPIO1 in R1 etc. The initial values of the R0 - R6 registers can be set up in the POI Voice macro which is ex ecuted when a power-on reset condition is detected. When the ISD2360 responds to a trigger event, if a Voice Macro is currently being executed, that Voice Macro is first stopped before execution of new Voice Macro.

10.1 ASSIGN PLAYBACK CHANNEL FOR THE GPIO TRIGGER

For each GPIO pins, Register 0x14 and 0x15 can assign the playback channel for that GPIO. So once triggered, the playback audio streaming will be routed to that channel.

10.2 VOICE MACRO EXAMPLES

Below are some useful examples demonstrating the features Voice trigger macros. The example project can be found in the ISD2360VPE distribution as the ISD2360example project.

10.2.1 POI/PU/WAKEUP Voice Macros

These special purpose Voice Macros allow the user to configure the ISD2360 for subsequent trigger events. The POI macro is executed when the chip receives an internal power -on reset condition or the SPI SW_RESET command is sent. The POI Voice macro is used to configure the ISD2360 for subsequent trigger events, for example: a. CFG(REG2, 0x44) ; Configure signal path to playback b. CFG(VOLC, 0x00) ; Set Volume to 0dB c. CFG(R5, 0x03) ; Set Jump register R5 to 0x03, GPIO5 to trigger VM#3 d. CFG(R4, 0x07) ; Set Jump register R4 to 0x07, GPIO4 to trigger VM#7 e. CFG(R3, 0x09) ; Set Jump register R3 to 0x09, GPIO3 to trigger VM#9 f. CFG(R2, 0x0a) ; Set Jump register R2 to 0x0a, GPIO2 to trigger VM#A g. CFG(R1, 0x0c) ; Set Jump register R1 to 0x0c, GPIO1 to trigger VM#C

• 18 - Publication Release Date: 10/22/2012 Revision 1.0 h. CFG(R0, 0x0e) ; Set Jump register R0 to 0x0e, GPIO0 to trigger VM#E i. PLAY_VP(FastBeep) ; Play Voice Prompt FastBeep j. CFG(REG_GPIO_AF1, 0xff) ; Set up GPIOs to trigger off falling edges k. CFG(REG_GPIO_AF0, 0x00) l. PD ; Power Down This POI macro will initialize the GPIO configuration such that all GPIO triggers are enabled for falling edges and performs initialization of the jump registers to point to appropriate Voice Macros. It also configures the play path and plays a beep. At the end of the macro the chip powers down. The GPIO_WAKEUP is executed whenever the device is triggered from a power down state. a. CFG(REG2, 0x44) ; Configure signal path to playback b. CFG(VOLC, 0x00) ; Set Volume to 0dB c. CFG(R4, 0x07) ; Set Jump register R4 to 0x07, GPIO4 to trigger VM#7 d. CFG(R2, 0x0a) ; Set Jump register R2 to 0x0a, GPIO2 to trigger VM#A e. Finish ; Exit Voice Macro, stay powered up. This GPIO_WAKEUP macro sets up the play path as settings in these registers are reset during power down. It also resets jump registers R4 and R2 to default conditions. 10.2.2 Example: Cycle through a sequence of messages. In this example a high -to-low transition on GPIO5 will initially trigger VM#3 as defined in the POI initialization macro. In VM#3 the Voice Prompt “One” is played and jump register R5 set to VM#4. Thus the next high -to-low transition on GPIO5 will trigg er VM#4 and play Voice Prompt “Two”. Similarly next trigger will play “Three” then “Four” and back to “One”. Notice the difference in VM#4 where a WAIT_INTERRUPT command has been inserted before the setting of the jump register. If the GPIO5/SW6 button is pushed rapidly, so that play is interrupted, “Two” will continue to be repeated. Other Voice Macros, because the jump register is changed first, will always progress to the next step in sequence.  VM#3: R5_Count_One (GPIO5) a. CFG(R5, 0x04) ; Configure GPIO5 to play VM#4 on next trigger b. Play(One) ; Play voice prompt “One” c. PD ; Power Down  VM#4:Two a. Play(Two) ; Play voice prompt “Two” b. Wait Interrupt ; Wait until Play finishes c. CFG(R5, 0x05) ; Configure GPIO5 to play VM#5 on next trigger d. PD ; Power Down  VM#5: Three a. CFG(R5, 0x06) ; Configure GPIO5 to play VM#6 on next trigger b. Play(Three) ; Play voice prompt “Three” c. PD ; Power Down  VM#6: Four a. CFG(R5, 0x03) ; Configure GPIO5 to play VM# 3 on next trigger b. Play(Four) ; Play voice prompt “Four “ c. PD ; Power Down

• 19 - Publication Release Date: 10/22/2012 Revision 1.0 10.2.3 Example: Looping short sounds. Interrupt to stop playback. This example demonstrates how to loop short sound samples and use a trigger inter rupt to stop playback. A trigger on GPIO4 will play a series of Voice Prompts until it is interrupted by another trigger to stop playback. VM#7 was associated with the GPIO4 trigger in the POI routine. The first action of this VM is to change the trigger V M to VM#8, thus if GPIO4 is re -triggered while the Voice Macro is running it will execute the power down voice macro rather than start the play sequence again. The next command sets the LRMP bit of REG1, under normal operation the compressor ramps signal level to zero after a sound sample is played to prevent a DC voltage appearing on the output. The LRMP bit prevents this from happening while a sample is looping allowing continuous audio. To loop a sound sample, the audio should be edited such that the las t sample loops smoothly to the first. To do this, create the sample in a sound editor at the sample rate desired for storage then find the first sample that returns to the initial condition and cut back audio to one before this sample. Note that tones require different lengths to fulfill these conditions at a given sample rate and thus loop numbers vary to produce the same length of output audio. At the end of the VM REG1 is reset and the trigger is re-enabled back to VM#7 before powering down.  VM#7: R4_PlayLoop (GPIO4) a. CFG(R4, 0x08) ; Configure GPIO4 to execute VM# 8 on next trigger. b. CFG(REG1, 0x20) ; Configure LRMP bit in REG1 c. LOOP_VP(Do,20) ; LOOP “Do” 20 times. d. LOOP_VP(Re,250) ; LOOP “Re” 250 times. e. LOOP_VP(Mi,5) ; LOOP “Mi” 5 times. f. LOOP_VP(Fa,33) ; LOOP “Fa” 33 times. g. LOOP_VP(So,10) ; LOOP “So” 10 times h. LOOP_VP(La,10) ; LOOP “La” 10 times i. LOOP_VP(Si,7) ; LOOP “Si” 7 times. j. Silence (128 ms) ; Insert 128ms of silence k. CFG(REG1, 0x00) ; Reset REG1 l. CFG(R4, 0x07) ; Configure GPIO4 to execute VM#7 on next trigger. m. PD ; Power Down  VM#8: PD_R4 a. CFG(REG1, 0x00) ; Configure Register one to its default value 00 b. CFG(R4, 0x07) ; Configure GPIO4 to execute VM#7 on next trigger. c. PD ; Power Down 10.2.4 Example: Uninterruptable Trigger, smooth audio. In this example a single trigger on GPIO3 will sequence through several messages until all messages are played the playback cannot be interrupted by an y other trigger. The example also demonstrates how to use begin and end segments to create smooth playback. Each “no te” consists of concatenating three voice prompts, for instance “So_begin” “So” and “So_end”. The begin and end prompts ramp the audio smoothly to avoid sudden transients in sound level. The middle, full amplitude, section is created by looping a short sample. At the beginning of the Voice Macro, all triggers are disabled so that Voice Macro cannot be interrupted from any source. The NRMP bit of REG1 is set so that concatenation of audio occurs without any ramp down between prompts. At the end of the macro , interrupts are re -enabled and device is powered down.

• 20 - Publication Release Date: 10/22/2012 Revision 1.0  VM#9: R3_Non-Int_Smooth (GPIO3) a. CFG(REG_GPIO_AF1, 0x00) ; Disable all triggers. b. CFG(REG1, 0x04) ; Set NRMP bit c. PLAY_VP(So_begin) ; Play “So_begin” d. LOOP_VP(So,10) ; Loop “So” 10 times. e. PLAY_VP(So_end) ; Play “So_end” f. PLAY_VP(Fa_begin) g. LOOP_VP(Fa,33) h. PLAY_VP(Fa_end) i. PLAY_VP(Mi_begin) j. LOOP_VP(Mi,5) k. PLAY_VP(Mi_end) l. PLAY_VP(Re_begin) m. LOOP_VP(Re,250) n. PLAY_VP(Re_end) o. PLAY_VP(Do_begin) p. LOOP_VP(Do,20) q. PLAY_VP(Do_end) r. Wait Interrupt ; Wait for audio to finish s. CFG(REG1, 0x00) ; Reset NRMP bit t. CFG(REG_GPIO_AF1, 0x3f) ; Re-enable interrupts u. PD ; Power down device. 10.2.5 Example: Continuous Play until re-trigger. In this example a single trigger on GPIO2 will sequence through several messages with pause in between each message. Messages are played in a loop indefinitely until another trigger occurs on GPIO2 to stop playback.  VM0#A: R2_Loop_VM (GPIO2) a. CFG(R2, 0x0b) ; Set Trigger to VM#B (PD_R2) b. PLAY_VP(One) ; Play “One” c. Silence (256 ms) ; pause 256ms d. PLAY_VP(two) ; Play “Two” e. Silence (256 ms) f. PLAY_VP(three) g. Silence (736 ms) h. PLAY_VP(four) i. Silence (256 ms) j. EXE_VM(0xA) ; Execute VM#A (repeat) k. Finish  VM0#B: PD_R2 a. CFG(R2, 0x0a) ; Reset Trigger to VM#A b. PD ; Power Down.

• 21 - Publication Release Date: 10/22/2012 Revision 1.0 10.2.6 Example: Level Hold Trigger. In this examp le holding GPIO1 will play several messages. Releasing GPIO1 will stop the playback. No other triggers will affect operation.  VM#C: R1_Level_Hold (GPIO1) a. CFG(REG_GPIO_AF0, 0x02) ; Enable rising edge trigger for GPIO2 b. CFG(REG_GPIO_AF1, 0x02) ; Disable all triggers except GPIO2 c. CFG(R1, 0x0d) ; Set Trigger to VM#D (PD_R1) d. CFG(REG1, 0x20) e. LOOP_VP(Re,200) f. Silence (32 ms) g. LOOP_VP(Mi,4) h. Silence (32 ms) i. LOOP_VP(Fa,20) j. Silence (32 ms) k. CFG(REG1, 0x00) l. PLAY_VP(applause) m. PD  VM#D: PD_R1 a. CFG(REG_GPIO_AF0, 0x00) ; Disable rising edge trigger b. CFG(REG_GPIO_AF1, 0x3f) ; Re-enable all triggers. c. CFG(REG1, 0x00) ; Ensure REG1 reset d. CFG(R1, 0x0c) ; Set trigger to VM#C e. PD ; Power Down.

11 CHANNEL SELECTION AND EXECUTION CONTROL

11.1 SELECT CHANNEL FOR THE PLYABCK AND MIXING

For any play command such as PLAY_VM or PLAY_VP, etc, the playback occurs in either one channel or all three channels. In other words, user can either specify one single active channel for next playback operation, or make the next play operation happen in all three channels. Channel selection can be achieved by configuring register 0x0C. To mix two different sound effects from two channels, e.g. channel #0 and channel #1, user can first configure channel #0 as the active channel by writing 0bxxxxxx00 into register 0x0C, then send a play command to play the first sound effect; then configure channel #1 as the active channel by writing 0bxxxxxx01 into register 0x0C, then send another play command to play the second sound effect. This way sound effect mixing can be achieved. By Default, play operations will always happen in channel #0.

11.2 EXECUTION CONTROL

• 22 - Publication Release Date: 10/22/2012 Revision 1.0 The ISD2360 implemented several commands which allow user add fine control in a VM script execution.

11.2.1 Conditional Branch and Unconditional Jump

The ISD2360 can do mask branch which judges device’s current pin status and its internal status register value against the value in mask register, to decide if jump to a memory address (and start execution from there) or continue executing the next script command insi de the current VM. This gives the possibility of multi-tasking, i.e. let the ISD2360 do something during the play. The ISD2360 can also do an absolute jump, which jumps to a memory address and start execution from there. The new start address should be a valid command entry address; otherwise it will cause unknown behavior. The scope for the mask jump and absolute jump is global, i.e. the full range of the flash size.

11.2.2 Execution Delay / Pause

The ISD2360 has time counter for each channel. So it allows cust omer add delay during a VM execution. This adds the convenience for certain operations such as GPIO driving with time control.

• 23 - Publication Release Date: 10/22/2012 Revision 1.0

12 ELECTRICAL CHARACTERISTICS

12.1 OPERATING CONDITIONS

OPERATING CONDITIONS (INDUSTRIAL PACKAGED PARTS) CONDITIONS VALUES Operating temperature range (Case temperature) -40°C to +85°C Supply voltage (VDD) [1] +2.4V to +5.5V Ground voltage (VSS) [2] 0V Input voltage (VDD) [1] 0V to 5.5V Voltage applied to any pins (VSS –0.3V) to (VDD +0.3V) NOTES: [1] VDD = VCCD = VCCPWM [2] VSS = VSSD = VSSPWM

12.2 AC PARAMETERS

12.2.1 Internal Oscillator

PARAMETER SYMBOL MIN TYP MAX UNITS CONDITIONS Sample rate with Internal Oscillator -1% 32kHz +1% kHz Vdd = 3V. At room temperature

12.2.2 Speaker Outputs

PARAMETER SYMBOL MIN TYP[1] MAX UNITS CONDITIONS SNR, Memory to SPK+/SPK- SNRMEM_SPK 60 dB Load 150Ω [2][3] Output Power POUT_SPK VCC=5.0 0.95 W Load 8Ω [2] THD, Memory to SPK+/SPK- THD % <1% Load 8Ω [2] Minimum Load Impedance RL(SPK) 4 8 Ω Notes: [1] Conditions Vcc=3V, TA=25°C unless otherwise stated. [2] Based on 12-bit PCM. [3] All measurements are C-message weighted.

• 24 - Publication Release Date: 10/22/2012 Revision 1.0

12.3 DC PARAMETERS

PARAMETER SYMBOL MIN TYP [1] MAX UNITS CONDITIONS Supply Voltage VDD 2.4 5.5 V Input Low Voltage VIL VSS-0.3 0.3xVDD V Input High Voltage VIH 0.7xVDD VDD V Output Low Voltage VOL VSS-0.3 0.3xVDD V IOL = 1mA Output High Voltage VOH 0.7xVDD VDD V IOH = -1mA Pull-up Resistance RPU 50 kΩ Pull-down Resistance RPD 10 kΩ INTB Output Low Voltage VOH1 0.4 V Playback Current IDD_Playback 3 mA No Load [2] Standby Current ISB <1 10 µA VDD= 3.6V Input Leakage Current IIL 1 µA Force VDD Notes: [1] Conditions VDD=3V, TA=25°C unless otherwise stated [2] To calculate total current, add load dissipation into application specific load.

• 25 - Publication Release Date: 10/22/2012 Revision 1.0

12.4 SPI TIMING

SYMBOL DESCRIPTION MIN TYP MAX UNIT TSCK SCLK Cycle Time 60 --- --- ns TSCKH SCLK High Pulse Width 25 --- --- ns TSCKL SCLK Low Pulse Width 25 --- --- ns TRISE Rise Time for All Digital Signals --- --- 10 ns TFALL Fall Time for All Digital Signals --- --- 10 ns TSSBS SSB Falling Edge to 1st SCLK Falling Edge Setup Time 30 --- --- ns TSSBH Last SCLK Rising Edge to SSB Rising Edge Hold Time 30ns --- 50us --- TSSBHI SSB High Time between SSB Lows 20 --- --- ns TMOS MOSI to SCLK Rising Edge Setup Time 15 --- --- ns TMOH SCLK Rising Edge to MOSI Hold Time 15 --- --- ns TZMID Delay Time from SSB Falling Edge to MISO Active -- -- 12 ns TMIZD Delay Time from SSB Rising Edge to MISO Tri-state -- -- 12 ns TMID Delay Time from SCLK Falling Edge to MISO --- --- 12 ns TCRBD Delay Time: SCLK Rising Edge to RDY/BSYB Falling Edge -- -- 12 ns TRBCD Delay Time: RDY/BSYB Rising Edge to SCLK Falling Edge 0 -- -- ns

• 26 - Publication Release Date: 10/22/2012 Revision 1.0

13 APPLICATION DIAGRAM

13.1 SPI MODE APPLICATION

The following applic ations example is for reference only. It makes no representation or warranty that such applications shall be suitable for the use specified. Each design has to be optimized in its own system for the best performance on voice quality, current consumption, functionality etc. V MISO / GPIO 2 SCLK / GPI 1 SSB MOSI / GPIO 0 INTB / GPIO 3 RDY / BSYB / GPIO 4 V SSD V CCD CCD 0 . 1 µF µF V CCD V SSD _ PWM V CCD _ PWM V CCD _ PWM VCCD  10 K Data flow control SPI Interface - SPK + SPK - GPIO 5 0.1 µF ISD 2360 QFN - 32 Figure 13-1 ISD2360 Application Diagram Example for programming with a Microcontroller SPI Mode

• 27 - Publication Release Date: 10/22/2012 Revision 1.0

13.2 STANDALONE APPLICATION

The following applic ations example is for reference only. It makes no representation or warranty that such applications shall be suitable for the use specified. Each design has to be optimized in its own system for the best performance on voice quality, current consumption, functionality etc. Figure 135-2 ISD2360 Application Diagram Stand-Alone Mode MISO/GPIO2 SCLK /GPIO1 SSB MOSI/GPIO0 INTB/GPIO3 RDY/BSYB/GPIO4 V SSD V CCD VCCD µF V CCD VCCDPWM SPK+ SPK- GPIO5/XCLK 4.7 µF ISD2360 QFN-32 SWI SW2 SW3 SW4 SW5 SW6 NC 10 VCCDPWM VSSDPWM

• 28 - Publication Release Date: 10/22/2012 Revision 1.0

14 PACKAGE SPECIFICATION

The ISD2360 is available in a QFN 32-Lead package, as shown in Figure 14-1 QFN 32-Lead Package Lead 300-MIL SOP

• 29 - Publication Release Date: 10/22/2012 Revision 1.0 and an SOP 16-Lead package, as shown in Error! Reference source not found.. QFN 32L 5X5 mm2, Thickness 0.8 mm(Max) ,Pitch 0.5 mm (Saw Type) TICP EP SIZE 3.5X3.5 mm2 Figure 14-1 QFN 32-Lead Package

• 30 - Publication Release Date: 10/22/2012 Revision 1.0 Lead 300-MIL SOP Figure 14-2 SOP 16-Lead Package TOP VIEW

• 31 - Publication Release Date: 10/22/2012 Revision 1.0

ORDERING INFORMATION

Y: 32L-QFN S: 16L-SOP Duration 60: 64 Seconds * Based on 8kHz/4bit ADPCM Lead-Free Y: green Temperature I: Industrial -40C to 85C

• 32 - Publication Release Date: 10/22/2012 Revision 1.0

15 REVISION HISTORY

0.1 July 01, 2011 Initial draft.

0.2 Nov 22, 2011 Package update, Application Diagram update

0.3 Mar 21, 2012 Update package and ordering information

1.0 Oct 22, 2012 Update package information

• 33 - Publication Release Date: 10/22/2012 Revision 1.0 Nuvoton products are not designed, intended, authorized or warranted f or use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other appl ications intended to support or sustain life. Furthermore, Nuvoton products are not intended for applications wherein failure of Nuvoton products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Nuvoton for any damages resulting from such improper use or sales. The contents of this document are provided only as a guide for the applications of Nuvoton products. Nuvoton makes no representation or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to discontinue or make changes to specifications and product descriptions at any time without notice. No license, whether express or implied, to any intellectual property or other right of Nuvoton or others is granted by this publication. Except as set forth in Nuvoton's Standard Terms and Conditions o f Sale, Nuvoton assumes no liability whatsoever and disclaims any express or implied warranty of merchantability, fitness for a particular purpose or infringement of any Intellectual property. The contents of this document are provided “AS IS”, and Nuvoton assumes no liability whatsoever and disclaims any express or implied warranty of merchantability, fitness for a particular purpose or infringement of any Intellectual property. In no event, shall Nuvoton be liable for any damages whatsoever (including, w ithout limitation, damages for loss of profits, business interruption, loss of information) arising out of the use of or inability to use the contents of th is documents, even if Nuvoton has been advised of the possibility of such damages. Application examples and alternative uses of any integrated circuit contained in this publication are for illustration only and Nuvoton makes no representation or warranty that such applications shall be suitable for the use specified. The 100-year retention and 100K record cycle projections are based upon accelerated reliability tests, as published in the Nuvoton Reliability Report, and are neither warranted nor guaranteed by Nuvoton. This data sheet and a ny future addendum to this data sheet is(are) the complete and controlling ISD ® ChipCorder® product specifications. In the event any inconsistencies exist between the information in this and other product documentation, or in the event that other product documentation contains informati on in addition to the information in this, the information contained herein supersedes and governs such other information in its entirety. This datasheet is subject to change without notice. Copyright© 2005, Nuvoton Technology Corporation. All rights rese rved. ChipCorder ® and ISD ® are trademarks of Nuvoton Electronics Corporation. All other trademarks are properties of their respective owners. Headquarters Nuvoton Technology Corporation America Nuvoton Technology (Shanghai) Ltd. No. 4, Creation Rd. III 2727 North First Street, San Jose, 27F, 299 Yan An W. Rd. Shanghai, Science-Based Industrial Park, CA 95134, U.S.A. 200336 China Hsinchu, Taiwan TEL: 1-408-9436666 TEL: 86-21-62365999 TEL: 886-3-5770066 FAX: 1-408-5441797 FAX: 86-21-62356998 FAX: 886-3-5665577 http:www.nuvoton-usa.com/ http:www.nuvoton.com.tw/ Taipei Office Nuvoton Technology Corporation Japan Nuvoton Technology (H.K.) Ltd. 9F, No. 480, Pueiguang Rd. 7F Daini-ueno BLDG. 3-7-18 Unit 9-15, 22F, Millennium City, Neihu District Shinyokohama Kohokuku, No. 378 Kwun Tong Rd., Taipei, 114 Taiwan Yokohama, 222-0033 Kowloon, Hong Kong TEL: 886-2-81777168 TEL: 81-45-4781881 TEL: 852-27513100 FAX: 886-2-87153579 FAX: 81-45-4781800 FAX: 852-27552064 Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this datasheet belong to their respective owners.