HDRC255P-110J-490 HITRON | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

Features

/square6 310W 3U X 8HP CPCI Package /square6 16.6-160VDC 10:1 Wide Input Range /square6 Meet EN50155 Class S2 & C2 compliance /square6 Suitable for CPCI Express Application /square6 Wide Operating Temp. -40 °° °°C t +85 °° °°C /square6 N+1 Redundancy/Hot-Swappable /square6 Using 125 °° °°C Long Life Solid Capacitors /square6 CE Marking Level 3 Compliance Specification Input General Input Voltage 16.6-160VDC, nominal 110VDC Efficiency (120W) Typical 85% at 24VDC Input Current (F-L/120W) 6A at 24VDC 1.3A at 110VDC (310W) 88% at 48VDC & 89% at 110VDC (F-L/310W) 7.5A at 48VDC, 3.3A at 110VDC Switching Frequency 120KHz at nominal I/P 110VDC (No-Load) 0.35A at 24VDC, 0.45A at 110VDC Dielectric Withstand I/P-O/P: 3000VAC I/P-GND:1500VAC Soft Star Installed O/P-GND:1000VAC Inrush Current Peak 27A at nominal 110VDC Circuit Topology Resonant Forward circuit Input Connector Positronic 47-pin PCIH47M400A1 Transient Response Peak transient < 300mV & recovers Output within 3mS for 25% load-change Output Connector Positronic 47-pin PCIH47M400A1 Remote ON/OFF Available at [INH#] & [EN#] pins Line Regulation Typical 0.2% Power Fail Signal Available at [FAL#] pin Load Regulation V1/V2 typical ±1%, Power OK Signal Available for all outputs V3 typical ±2% V4 typical ±5% Status LED <Green> means valid input voltage Noise & Ripple Typical 1% Peak-Peak <Red> means a critical fault Remote Sense Available at V1,V2 & V3 N+1 Redundancy Internal OR-ing diodes Adjustability Available at V1, V2 & V3 Hot-Swappable Available Current Sharing Available at V1, V2 & V3 Power Density 2.2-5.5 Watts/Cubic Inch Output Trim Available at V1/2[ADJ #] Environmental Protection Operating Temperature -40 °C to +85 °C with de-rating Over Voltage Built-in at all outputs Storage Temperature -45°C to +90°C Over Current Installed in each rail. Cooling 150-310W:400-600LFM moving air Over Load Typical 120% max. load 90-120W:Convection air (Fanless) fully protected against output Safety/EMC overload or short circuit Emissions (conducted) CISPR EN55032 Class A Over Temperature Installed NTC for thermal sensor Safety Standard IEC60950-1 Class I at [DEG#] pin CE Standard Meet Level 3 Criteria A Input-Under & Installed Vibration Six degree-of-freedom random Over-Voltage 10Hz-150Hz, 10G Input Reverse Voltage Installed Radiated Susceptibility EN61000-4-3 Level X (20V/m) Conformal Coating Available Surge EN61000-4-5 Level 3 , L-L 2KV,L-G 2KV Conducted Disturbance EN61000-4-6 Level X (20V/m) Notes: (1) All measurement are at nominal input, full load and +25°C unless otherwise specifications. (2) Due to requests in market and advances in technology, specifications subject to change without notification. (3) A warm-up time 10 minutes is required after cold start at temperature from -40°C to +0°C. (4) Tantalum capacitors connected to system is suggested for bettering Ripple & Noise against operating temperature from -40°C to +0°C. (5) 125°C OS-CON Long-life Solid capacitors are installed in secondary circuits.

-2- Output voltage & current rating chart Quad Output Model No. Volt. Volt. Min. (Redundant) Min. (Single Unit) Typ. (Convection- cooled) Typ. (Forced- cooled) Max. (Convection- cooled) Max. (Forced- cooled) Peak HDRC255P-110J-490(E) V1 +5VDC 0.5A 0A 10A 20A 10A 33A 35A V2 +3.3VDC 0A 0A 5A 20A 10A 33A 35A V3 +12VDC 0A 0A 4A 11A 10A 20A 23A V4 -12VDC 0A 0A 0.5A 1A 2A 2A 3A Notes: (1) Maximum o/p power: 90-120W for convection cooling, 150-310W for 400 or 600LFM Forced air cooling. (2) Maximum load is the continuous operating load of each rail. But the maximum load of each rail can't be drawn from all outputs at the same time. (3) Total combined current of V1 & V2 should be ≦ 50A. (4) Minimum load is only required when PSUs do run in parallel. Mechanical Dimensions (All dimensions are in mm[inch]) Derating Chart Immunity to environmental conditions Standard Condition EN5015512.2.1 & 12.2.6 EN5015512.2.4 I/P: 24-110VDC O/P: 90-120W (Fanless) Pass Class S2 & Class C2 Pass Class TX & Column 1 Pass Class TX & Column 2 Pass Class TX & Column 3 I/P: 24-110VDC O/P: 310W Pass Class S2 Pass Class TX & Column 1 I/P: 24-110VDC O/P: 150 -310W Pass Class S2 Pass Class TX & Column 1 Pass Class TX & Column 2 I/P: 24-110VDC O/P: 120-310W Pass Class S2 Pass Class TX & Column 3 Pass Class TX & Column 4 Pin assignment Assignment -Vin +Vin GND V1 V1 S+ V1 Adj. V1 C.S. V2 V2 S+ V2 Adj. Pin # 47 46 45 1,2,3,4 30 29 35 13,14,15,16,17,18 33 32 Assignment V2 C.S. V1/V2 S- V3 V3 S+ V3 C.S. V4 DC COM EN# DEG# INH# FAL# Pin # 41 34 20 36 44 21 5,6,7,8,9,10,11 12,19,22,24 27 38 39 42