HDM30-S HITRON | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
-27- H HiTRON PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES
30 WATTS SINGLE OUTPUT HDM30-S SERIES
FEATURES: SINGLE OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED SHIELD OUTPUT SPECIFICATION Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P ±2.0% typical. Line Regulation: Various with input & output voltages. ±0.5% typical. Load Regulation: Various with output voltages. ±1.0% typical. Noise & Ripple: Typical 100mV for 3.3V/5.0V & 1.0% for others peak to peak. OVP: Built-in on main output. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting. SPECIFICATION INPUT SPECIFICATION Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. (Voltage refer to the –Input) Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin). OFF(Disable)=Short(or 0-0.8Vdc above-Vin). Negative Logic version option available by adding a “N” suffix to the end of Model #. GENERAL SPECIFICATION Efficiency: 81% typical various with input. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec.@ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10 Watts. / Cubic inch. MTBF: Type 1,000,000 hours to Mil. Std.217, 25°C. Operating Temperature: -10 to +70°C range. 0°C to +60°C full load without derating. From +60°C, derating linearly to half load @+70°C. (Refer to Derating Chart.) Temperature: -20°C to +85°C. Temperature Coefficient: 0.02% /°C. Cooling: Convection cooling up to +60°C @ full load. At least 100LFM moving air is recommended for full load > +60°C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only. NOTE: (1) All measurements are at nominal input, full load, and +25°C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drain at low Line input & Load and then adding 20-25％for the desired fuse size. Due to requests in market and advances in technology, specifications subject to change without notice.
-28- INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART SINGLE OUTPUT MODEL NO. INPUT Vdc INPUT CURRENT N. L. (mA) F . L . OUTPUT VO1(Vdc) @★ OUTPUT VO1(A) CASE SIZE HDM30-12B-S03 9.0- 18.0 30 2300 3.3V 6.40A DM2A HDM30-12B-S05 9.0- 18.0 30 2700 5.0V 5.00A DM2A HDM30-12B-S09 9.0- 18.0 30 2650 9.0V 2.80A DM2A HDM30-12B-S12 9.0- 18.0 30 2750 12.0V 2.20A DM2A HDM30-12B-S15 9.0- 18.0 30 2800 15.0V 1.80A DM2A HDM30-12B-S24 9.0- 18.0 30 3100 24.0V 1.25A DM2A HDM30-24B-S03 18.0- 36.0 20 1150 3.3V 6.40A DM2A HDM30-24B-S05 18.0- 36.0 20 1350 5.0V 5.00A DM2A HDM30-24B-S09 18.0- 36.0 20 1325 9.0V 2.80A DM2A HDM30-24B-S12 18.0- 36.0 20 1375 12.0V 2.20A DM2A HDM30-24B-S15 18.0- 36.0 20 1400 15.0V 1.80A DM2A HDM30-24B-S24 18.0- 36.0 20 1550 24.0V 1.25A DM2A HDM30-48B-S03 36.0- 72.0 15 575 3.3V 6.40A DM2A HDM30-48B-S05 36.0- 72.0 15 675 5.0V 5.00A DM2A HDM30-48B-S09 36.0- 72.0 15 662 9.0V 2.80A DM2A HDM30-48B-S12 36.0- 72.0 15 687 12.0V 2.20A DM2A HDM30-48B-S15 36.0- 72.0 15 700 15.0V 1.80A DM2A HDM30-48B-S24 36.0- 72.0 15 775 24.0V 1.25A DM2A HDM30-24D-S03 9.0- 36.0 30 1175 3.3V 6.40A DM2A HDM30-24D-S05 9.0- 36.0 30 1375 5.0V 5.00A DM2A HDM30-24D-S09 9.0- 36.0 30 1350 9.0V 2.80A DM2A HDM30-24D-S12 9.0- 36.0 30 1400 12.0V 2.20A DM2A HDM30-24D-S15 9.0- 36.0 30 1425 15.0V 1.80A DM2A HDM30-24D-S24 9.0- 36.0 30 1575 24.0V 1.25A DM2A HDM30-48D-S03 20.0- 72.0 20 587 3.3V 6.40A DM2A HDM30-48D-S05 20.0- 72.0 20 687 5.0V 5.00A DM2A HDM30-48D-S09 20.0- 72.0 20 675 9.0V 2.80A DM2A HDM30-48D-S12 20.0- 72.0 20 700 12.0V 2.20A DM2A HDM30-48D-S15 20.0- 72.0 20 712 15.0V 1.80A DM2A HDM30-48D-S24 20.0- 72.0 20 787 24.0V 1.25A DM2A Symbols: "★" OVP built-in. "@" Adjustable. MECHANICAL DIMENSIONS: M M [ I N C H E S ] W E I G H T : 156.0g (5.6 Oz.) DERATING CHART PIN ASSIGNMENT PIN NO. SINGLE PIN #1. Remote ON/OFF PIN #2. +INPUT PIN #3. -INPUT/-Vin PIN #4. NO PIN PIN #5. NO PIN PIN #6. OUTPUT TRIM PIN #7. NO PIN PIN #8. +VO1 PIN #9. DC-COM PIN #10. NO PIN CASE SIZE: DM2A
-29- H HiTRON PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES
30 WATTS DUAL OUTPUT HDM30-D SERIES
Efficiency: 76- 81% typical, various with input & output voltage. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: 100K Hz. Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec. @ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10.0 Watts. / Cubic inch. MTBF: 1,000,000 hours to Mil. Std. 271, 25°C. Operating Temperature: -10°C to +70°C range. 0°C to +60°C @ full load without derating. From +60°C, derating linearly to half load@+70°C. (Refer to the Derating Chart). Temperature: -20°C to +85°C. Temperature Coefficient: ± 0.03% /°C. Cooling: Convection cooling up to +60°C @ full load. At least 100LFM moving air is recommended for F-L > +60°C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only. NOTE: (1) All measurements are at nominal input, full load, and +25°C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size. SPECIFICATION INPUT SPECIFICATION Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. (Voltage refer to the -Input). Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin). OFF(Disable)=Short(or 0-0.8Vdc above-Vin). Negative Logic version option available by adding a “N” suffix to the end of Model #. Remark: Logic voltage refer to –Input (-Vin) FEATURES: DUAL OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED METAL SHIELD OUTPUT SPECIFICATION Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P ±2.0% typical. Line Regulation: Various with input voltages. ±0.5% typical. Load Regulation: Various with output voltages. VO1 ±1.0% typical. VO2 ±2.0% typical. Noise & Ripple: 100mV for 3.3V/5.0V & 1.0% typical for other output peak to peak. OVP: Built-in on main output. Adjustability: VO1 O/P may optionally be external trimmed ±3.0% with a fixed resistors or trim-pot. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting. Due to requests in market and advances in technology, specifications subject to change without notice.
-30- INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART DUAL OUTPUT INPUT CURRENT OUTPUT (Vdc) OUTPUT (A) MODEL NO. INPUT Vdc N.L. (mA) F.L. +VO1@★ -VO2‖ +VO1 -VO2 CASE SIZE Symbols: "★" OVP built-in. "@" Adjustable. " ‖" Double Feedback. MECHANICAL DIMENSIONS: M M [ I N C H E S ] W E I G H T : 156.0g (5.6 Oz.) PIN ASSIGNMENT PIN NO. DUAL PIN# 1. Remote ON/OFF PIN# 2. + INPUT PIN# 3. -INPUT/-Vin PIN# 4. NO PIN PIN# 5. +VO1 PIN# 6. DC-COM PIN# 7. -VO2 PIN# 8. OUTPUT TRIM PIN# 9. NO PIN PIN# 10. NO PIN DERATING CHART CASE SIZE: DM2A
-31- H HiTRON PCB-MOUNT DC-DC CONVERTER ENCAPSULATED MODULES
30 WATTS TRIPLE OUTPUT HDM30-T SERIES
Output Voltage: See Ratings Chart. Output Current: See Ratings Chart. Voltage Accuracy: Main O/P ±2.0% typical. Line Regulation: Various with input voltages. ±0.5% typ. Load Regulation: Various with output voltages. VO1 & VO3 ±2.0% typical. VO2 ±5.0% typical. Noise & Ripple: 100mV for 3.3V/5.0V & 1.0% typical for other output peak to peak. OVP: Built-in on main output. Adjustability: VO1 O/P may optionally be external trimmed ±3.0% with a fixed resistors or trim-pot. Overload Protection (OLP): Fully protected against output overload and short circuit. OLP set at about 125-150% rating output wattage. Consult the factory for OLP setting. SPECIFICATION INPUT SPECIFICATION Input Range: Wide 4:1 & 2:1 DC input range. See Ratings Chart. Input Voltage: Nominal 12/24/48Vdc. Input Current: Various with input range and load. See Ratings Chart. Input Fuse: Use external fuse. Input Filter: Pi-Network. Overvoltage Shutdown: Optional. Factory set. Undervoltage Shutdown: 8Vdc. Isolation Resistor: 1,000 Mega Ohms. Isolation Voltage: 1,500Vdc. EMI: Six-sided metal shielding. Remote On/Off: TTL/CMOS-Compatible Input Control. Positive Logic version for Standard set up: ON(Enable)=Open(or 2.5-5.0Vdc above-Vin) OFF(Disable)=Short(or 0-0.8Vdc above-Vin) Negative Logic version option available by adding a “N” suffix to the end of Model #. Remark: [Voltage refer to –Input (-Vin)]. GENERAL SPECIFICATION Efficiency: 78-81% typical, various with input & output voltage. Switching Frequency: Fixed frequency 100K Hz. Circuit Topology: 100K Hz. Forward Circuit. Transient Response: Peak deviation 200mV, Recovery time < 3mSec. @ 25% step load change. Case: Black coated copper with non-conductive metal base. Power Density: 10.0 Watts. / Cubic inch. MTBF: 1,000,000 hours Mil.Std.271, 25°C. Operating Temperature: -10°C to +70°C range. 0°C to +60°C @ full load without derating. From+60°C derating linearly to half load@+70°C. (Refer to the Derating Chart). Storage Temperature: -20 to +85°C. Temperature Coefficient: ± 0.03% /°C. Cooling: Convection cooling up to +60°C @ full load. At least 100LFM moving air is recommended for full load > +60°C in a confined area. Humidity: Up to 95%RH, Non-condensing. Commercial Grade only. NOTE: (1) All measurements are at nominal input, full load, and +25°C unless otherwise specified. (2) Line Regulation measured from High to Low Lines at full load. (3) Load Regulation measured from Full Load to 1/2 Full Load at nominal input. (4) Correct fuse size by calculating the max. DC current drains at low Line input & Load and then adding 20-25% for the desired fuse size. FEATURES: TRIPLE OUTPUT WIDE 4:1 & 2:1 INPUT RANGE 30W ISOLATED OUTPUT SIX-SIDED METAL SHIELD Due to requests in market and advances in technology, specifications subject to change without notice.
-32- INPUT/OUTPUT & VOLTAGE/CURRENT RATINGS CHART TRIPLE OUTPUT INPUT CURRENT OUTPUT (Vdc) OUTPUT (A) MODEL NO. INPUT Vdc N.L. (mA) F.L. +VO1★@ +VO2† -VO3‖ +VO1 +VO2 -VO3 CASE SIZE Symbols: "★" OVP built-in. "@" Adjustable. " ‖" Double Feedback. " †" Stacked on main O/P. MECHANICAL DIMENSIONS: M M [ I N C H E S ] W E I G H T : 156.0g (5.6 Oz.) PIN ASSIGNMENT PIN NO. TRIPLE PIN# 1. Remote ON/OFF PIN# 2. +INPUT PIN# 3. - INPUT/-Vin PIN# 4. NO PIN PIN# 5. +VO2 PIN# 6. DC-COM PIN# 7. -VO3 PIN# 8. + VO1 PIN# 9. NO PIN PIN# 10. OUTPUT TRIM DERATING CHART CASE SIZE: DM2A