GP2W0001YP SHARP | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 15
Technical content
IrDA Data Sheet 115 kbps Transceiver
FEATURES
- Built-in Photodiode Operating voltage 2.7 V to 5.5 V In circuit design, allow for the degradation of light emitting diode output that results from long continu- ous operation (50% degradation/5 years). This product shall not contain the following materi- als, and these materials shall not be used in the pro- duction process for this product. –C F C s – Halon – Carbon Tetrachloride – 1.1.1. Trichloroethane (Methylchloroform) – Specific brominated flame retardants such as the PBBOs and PBBs are not used in this device. INTRODUCTION This specification applies to the outline and charac- teristics of IrDA 1.2 type (data rate 2.4 kbps to 115.2 kbps, low power option compliant) optical data communication transceiver. NOTES Caution should be taken to prevent the detector sur- face from being smeared with dust or dirt, or from being touched, as it may cause faulty operation. Cleaning conditions: – Solvent cleaning: Solvent temperature 45°C or less. Immersion for 3 minutes or less. – Ultrasonic cleaning: The effect of ultrasonic cleaning on the device differs by cleaning bath size, ultrasonic power output, cleaning time, PCB size or device mounting condition, etc. Test the device under actual conditions and confirm that ultrasonic cleaning does not cause any immedi- ate or potential defects. – Cleaning solvent: The cleaning shall be carried out with ethyl alcohol, methyl alcohol, or isopropyl alcohol. In order to prevent electrostatic damage to the inte- grated circuit, handle this device in a static-free envi- ronment and workstation. External force applied to the device after mounting can cause mounting defects such as the terminal coming off. Be careful when handling the device and prevent objects from touching the device after mounting. Refer to the ‘Precautions for Soldering’ section. When the system (program) is designed, the turn around time from transmit to receive should be designed by considering 0.5 ms or more that is spec- ified by IrDA. This turn around time means the time that this device temporarily does not detect the incoming signal, since the transmitted light from the transmitter side reaches the detector side of the same transceiver. Consider that 20 ms or more (at T A = 25°C, no input signal) is necessary to return from shut-down mode to ready operation mode. In addition, thoroughly confirm the operation in the actual application. When there is considerable external stray light or a light source is located near the transceiver, or the detector face receives considerable external stray light, a pulse other than the desired signal output may be generated as noise on the output terminal of the transceiver. Consider the layout and structure in your design to minimize disturbing light on the detector face. When the sensor is adopted in an IR communication system, it should be used according to the signal method specified by ‘Serial Infrared Physical Layer Link Specification’ published by the Infrared Data Association. Faulty operation may occur if a signal method other than that specified is used.
Figure 1. Recommended External Circuit the noise level and noise frequency of power supply.
2 IrDA Data Sheet
Figure 2. System Example
1 Transmitting data waveform
3 Transmitter output optical signal waveform
4 GP2W0001YP receiver output waveform
dering must be as large as the foot pattern landings. Figure 3. Signal Waveform Example Figure 4. Foot Pattern and NOTES: Dimensions are in mm.
4 IrDA Data Sheet
Figure 5. GP2W0001YP Outline Dimensions
- Unspecified tolerances are ±0.3 mm.
- Adhesion of resin to the terminal area are allowed MAX. 0.3 mm.
- Resin burr are not included in this outline drawing.
- Product mass: Approx. 0.12 g
- Mold resin: Epoxy resin (black)
115 kbps Transceiver GP2W0001YP IrDA Data Sheet 5 RATINGS AND CHARACTERISTICS Absolute Maximum Ratings NOTES: 1. Pulse width: 78.1 µs. Duty ratio: 3/16. 2. Soldering reflow time: 5 seconds. Recommended Operating Conditions NOTES: *Recommended circuit of emitter side. PARAMETER SYMBOL RATINGS UNIT NOTES Supply voltage V CC 0 to 6.0 V Forward current I F 50 mA Peak forward current I FM 500 mA 1 Operating temperature T OPR -10 to +70 °C Storage temperature T STG -20 to +85 °C Soldering temperature T SOL 230 °C2 PARAMETER SYMBOL OPERATING CONDITION UNIT Supply voltage V CC 2.7 to 5.5 V Data rate BR 2.4 to 115.2 kbps Shutdown circuit high level input voltage V IHSD VCC – 0.6 to VCC V Shutdown circuit low level input voltage V ILSD 0.0 to 0.4 or Open V Logic high transmitter input voltage* V IHTXD 2.4 to VCC V Logic low receiver input voltage* V ILTXD 0.0 to 0.4 V
GP2W0001YP 115 kbps Transceiver
6 IrDA Data Sheet
Electrical Characteristics
TA = -25°C, VCC = 5 V unless otherwise specified NOTES: 1. V CC = 5 V, no input signal, output terminal open, V IHSD = VCC -0.6 V. 2. V CC = 3 V, no input signal, output terminal open, V IHSD = VCC -0.6 V. 3. V CC = 5 V, SD terminal open. 4. V CC = 3 V, SD terminal open. 5. V CC = 5 V. 6. V CC = 3 V. 7. V CC = 5 V, IOL = 400 µA. 8. V CC = 3 V, IOL = 400 µA. See Figures 6, 7, and 8. 9. BR = 115.2 kbps. See Figures 6, 7, and 8. 10.V OH, VOL, tw, tr, tf shall be satisfied at φ ≤ 15°. See Figures 6, 7, and 8. 11.BR = 115.2 kbps, φ ≤ 15°, VCC = 3 V, RL = 2.2 Ω, VINTX = 2.7 V, R2 = 1 kΩ ±5%, CX2 = 1,500 pF. See Figures 9, 10, and 11. PARAMETER SYMBOL MIN. TYP. MAX. UNIT NOTES Current consumption at no input signal ICC1 1.0 1.4 mA 1 ICC2 0.7 1.0 mA 2 Current consumption at shut-down mode ICC1-S 0.5 1.0 µA 3 ICC2-S 0.3 1.0 µA 4 High level output voltage VOH1 4.5 V 5 VOH2 2.5 V 6 Low level output voltage VOL1 0.6 V 7 VOL2 0.6 V 8 Low level pulse width tw 0.8 8.0 µs 9 Rise time tr 1.2 µs 9 Fall time tf 0.2 µs 9 Maximum reception distance L 1 m 10 Radiant intensity I E 40 350 mW/Sr 11 Peak emission wavelength λp 850 870 900 nm 11 Figure 6. Input Signal Waveform (Detector Side) Figure 7. Output Waveform (Detector Side)
8 IrDA Data Sheet
Figure 10. Standard Optical System (Emitter Side) Figure 11. Recommended Circuit (Emitter Side) Figure 12. Peak Forward Current
115 kbps Transceiver GP2W0001YP IrDA Data Sheet 9 RELIABILITY1 NOTES: 1. Confidence level 90%, LTPD 10%/20%. 2. The sample to be tested shall be left at normal temperature and humidity for 2 hours after it is taken out of the chamber. No dew point. 3. Refer to the ‘Precautions for Soldering’ section for temperature profile. TEST ITEMS TEST CONDITIONS FAILURE JUDGEMENT CRITERIA SAMPLES (n) DEFECTIVE (c) NOTES Temperature cycling 1 cycle -20°C to 85°C (30 minutes at each extreme) 20 cycles test ICC1 > Up × 1.2 ICC2 > Up × 1.2 L < Low × 0.8 Judgement of Criteria: VOH1 < Low × 0.8 VOH2 < Low × 0.8 VOL1 > Up × 1.2 VOL2 > Up × 1.2 tw1 > Up × 1.2 tw1 < Low × 0.8 tw2 > Up × 1.2 tw2 < Low × 0.8 tr > Up × 1.2 tf > Up × 1.2 Up: Upper Specification Limit Low: Lower Specification Limit n = 22 c = 0 2 High temperature and high humidity storage +40°C, 90% RH, 240 hours n = 22 c = 0 2 High temperature storage +85 °C, 240 hours n = 22 c = 0 2 Low temperature storage -20 °C, 240 hours n = 22 c = 0 2 Operation life 1 +25 °C, VCC = 5 V, 240 hours n = 11 c = 0 2 Operation life 2 +25°C, IFM = 400 mA, 240 hours, Pulse width 78.1 µs, Duty ratio 3/16 n = 11 c = 0 Mechanical shock 1,000 m/s2, 6 ms, 3 times/±X, ±Y, ±Z direction n = 11 c = 0 Variable frequency vibration 200 m/s2, 100 to 2,000 to 100 Hz for approximately 4 minutes 48 minutes/X, Y, Z direction n = 11 c = 0 Reflow solder heat 230 °C, 5 s. n = 11 c = 0 3
10 IrDA Data Sheet
within the temperature profile as shown in Figure 13. package temperature within that specified in Figure 13. break if the deformation of the PCB affects the lead pins. Soldering time shall be within 3 seconds. Soldered product shall treat at normal temperature. Solder: 6/4 solder or included Ag solder. Table 1. Incoming Inspection Figure 13. Temperature Profile
side of product is placed on the hold side of the tape. to 1 N for the angle from 160° to 180°. the reel so that the cover tape is on the outside. adhesive tape. One reel shall contain 2,000 pieces. trical characteristics due to shipping. Figure 14. Tape Structure and Dimensions GP2W0001YP-14NOTE: Dimensions are in mm.
12 IrDA Data Sheet
Figure 15. Reel Structure and Dimensions Figure 16. Direction of Product Insertion GP2W0001YP-15NOTE: Dimensions are in mm.
tape reel (2,000 pieces per reel) and desiccant. it on the aluminum laminate bag. quantity should be one laminated bag. 30°C, at the humidity condition of below 60% RH. Devices must be mounted within two weeks. – Recommended condition: 100°C, 12 to 24 hours. done using adhesive, not by soldering. Table 2. Packaging Material Table 3. Packaging Method Specifications
14 IrDA Data Sheet
Figure 17. Packing Specification
- Seal the aluminum laminated bag, including the tape reel
with 2,000 pieces and desiccant.
- Fill out the model name, quantity etc. in the blank area of label
- Put the four moisture-proof laminated bags in the ruled case.
Put the pad between the bags, and top and bottom.
- Seal the case with packing tape, and indicate model name
Total Packaged mass: Approximately 3.6 kg.
115 kbps Transceiver GP2W0001YP ©2000 by SHARP Corporation Reference Code SMA00011 NORTH AMERICA EUROPE ASIA SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (360) 834-2500 Telex: 49608472 (SHARPCAM) Facsimile: (360) 834-8903 http://www.sharpsma.com SHARP Electronics (Europe) GmbH Microelectronics Division Sonninstraße 3
20097 Hamburg, Germany
Phone: (49) 40 2376-2286 Facsimile: (49) 40 2376-2232 http://www.sharpmed.com LIFE SUPPORT POLICY SHARP components should not be used in medical devices with life support functions or in safety equipment (or similiar applications where component failure would result in loss of life or physical harm) without the written approval of an officer of the SHARP Corporation. LIMITED WARRANTY SHARP warrants to its Customer that the Products will be free from defects in material and workmanship under normal use and service for a period of one year from the date of invoice. Customer's exclusive remedy for breach of this warranty is that SHARP will either (i) repair or replace, at its option, any Product which fails during the warranty period because of such defect (if Customer promptly reported the failure to SHARP in writing) or, (ii) if SHARP is unable to repair or replace, refund the purchase price of the Product upon its return to SHARP. This warranty does not apply to any Product which has been subjected to misuse, abnormal service or handling, or which has been altered or modified in design or construction, or which has been serviced or repaired by anyone other than Sharp. The warranties set forth herein are in lieu of, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will Sharp be liable, or in any way responsible, for any incidental or consequential economic or property damage. The above warranty is also extended to Customers of Sharp authorized distributors with the following exception: reports of failures of Products during the warranty period and return of Products that were purchased from an authorized distributor must be made through the distributor. In case Sharp is unable to repair or replace such Products, refunds will be issued to the distributor in the amount of distributor cost. SHARP reserves the right to make changes in specifications at any time and without notice. SHARP does not assume any responsibility for the use of any circuitry described; no circuit patent licenses are implied. SHARP Corporation Integrated Circuits Group 2613-1 Ichinomoto-Cho Tenri-City, Nara, 632, Japan Phone: +81-743-65-1321 Facsimile: +81-743-65-1532 http://www.sharp.co.jp