GH06510B2A SHARP | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Notice In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/ I Absolute Maximum Ratings (TC=25˚C ❇ 1) ❇ 1 Case temperature ❇ 2 At the position of 1.6mm or more from the lead base (5s) Parameter Symbol Rating Unit Optical power output P O 10 mW Reverse voltage Laser V rl 2V Monitor photodiode 30 ❇ 1 Operating temperature Top(c) -10 to +70 ˚C Storage temperature T stg -40 to +85 ˚C ❇ 2 Soldering temperature Tsld 260 ˚C Vrd V GH06510B2A I Features (1) Maximum optical power output : 10mW CW (2) Wavelength : TYP. 654nm (3) Low current drive type (Iop : 40mA) (4) φ5.6mm package I Applications (1) DVD-ROM drives (2) DVD video drives I Outline Dimensions Red Laser Diode for DVD-ROM Drive(654nm-10mW) (Unit : mm) Reference plane Laser chip Emission point Cap glass Monitor PD X ø 2.0Y Z 0.4±0.1 3-ø 0.45±0.1 ø 1.2 MAX. 0.5 MIN. ø 3.55±0.1 ø 5.6 0.025 ø 4.4MAX. ø 1.0 MIN. 0.5 MAX. burr0.1 MAX. 2.3±0.5 1.2±0.1 1.27±0.08 6.5±1.0 Tolerance ±0.2mm ❇ 2 ❇ 2 ❇ 2 ❇ 1 90 ±2 Terminal connection Enlarged view of emission point Center of virtual circle that runs 3 points on the stem periphery Emission point 0±0.08 0±0.08 X Y ❇ 1 : Dimension measured at lead base ❇ 2 : Within 0.6mm from reference plane q w e Dual power supply Laser diode Monitor photodiode
I Electro-optical Characteristics❇ 1 (TC=25˚C) Parameter Symbol MAX. Unit Threshold current I th 45 mA Half intensity angle ❇ 2❇ 3 Parallel θ// 10 ˚ ❇ 4 Ripple Rl ±20 % Misalignment angle ∆θ⊥ ±3 ❇ 1 Initial value, CW (Continuous Wave) drive ❇ 2 Angle at 50% peak intensity (full-width at half-maximum) ❇ 3 Parallel to junction plane (X-Z plane), Perpendicular to the junction plane (Y-Z plane) ❇ 4 Rl=∆P/P ∆P : the maximum deviation of the far field pattern from its approximate curve P : the peak of the approximate curve Conditions MIN. TYP. − -3 0 78 . 5 ❇ 2❇ 3 Perpendicular 24 29 Operating current I op Po=7mW -4 0 5 5 m A Operating voltage V op -2 . 2 2 . 5 V Wavelength λp 640 654 660 nm ❇ 3 Parallel ∆θ// -- ±2 ˚ ❇ 3 Perpendicular Interference pattern intensity α Po=7mW - - 1 - Differential efficiency ηd 5mW I(7mW)-I(2mW) 0.38 0.7 1.05 mW/mA I Electrical Characteristics of Photodiode (TC=25˚C) Parameter Symbol MAX. Unit Terminal capacitance Ct - pF Conditions MIN. TYP. Vrd=5V, f=1MHz - 3.5 Dark current I D Vrd=5V - - 150 nA Output current I m Po=7mW, Vrd=5V 0.08 0.2 0.4 mA
l The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. l Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. l Observe the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). l Contact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. l If the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. l This publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. l Contact and consult with a SHARP representative if there are any questions about the contents of this publication.