G150XG01V1 AUO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 27
Technical content
Datasheet sections
- 2.1 Display Characteristics
- 2.2 Optical Characteristics
- 4.1 Absolute Ratings of TFT LCD Module
- 4.2 Absolute Ratings of Environment
- 5.1 TFT LCD Module
- 5.2 Backlight Unit
- 6.1 Pixel Format Image
- 6.2 Scanning Direction
- 6.3 Signal Description
- 6.4 The Input Data Format
- 6.5 Interface Timing
- 6.6 Power ON/OFF Sequence
- 7.1 TFT LCD Module: LVDS Connector
- 7.2 Backlight Unit: Lamp Connector
- 7.3 Lamp Connector Pin Assignment
- 9.1 LCM Front View and Rear View
- 9.2 LCM Outline Dimension (Front View)
- 9.3 LCM Outline Dimension (Rear View)
- 10.1 Shipping Label (on the rear side of TFT-LCD display)
- 10.2 Carton Package
- 11 Safety
- 11.1 Sharp Edge Requirements
- 11.2 Materials
- 11.3 Capacitors
- 11.4 National Test Lab Requirement
G150XG01 V1 rev. 0.0 G150XG01 V1 (V ) Preliminary Specifications ( ) Final Specifications Module 15 Inch Color TFT-LCD Model Name G150XG01 V1 Customer Date Checked & Approved by Note: This Specification is subject to change without notice. Approved by Date Debbie Chiu 2007/05/15 Prepared by Danny Wang 2007/05/15 General Display Business Division / AU Optronics corporation
G150XG01 V1 rev. 0.0 G150XG01 V1 Record of Revision Version and Date Page Old description New Description 0.0 2007/05/15 All First Edition
G150XG01 V1 rev. 0.0 G150XG01 V1 1. Operating Precautions 1) Since front polarizer is easily damaged, please be cautious and not to scratch it. 2) Be sure to turn off power supply when inserting or disconnecting from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or soft cloth. 5) Since the panel is made of glass, it may be broken or cracked if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the module assembly. 8) Do not press the reflector sheet at the back of the module to any direction. 9) In case if a module has to be put back into the packing container slot after it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface Connector of the TFT Module. 11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for example), do not twist nor bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption. 14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit (IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit. 15) Severe temperature condition may result in different luminance, response time and lamp ignition voltage. 16) Continuous operating TFT-LCD display under low temperature environment may accelerate lamp exhaustion and reduce luminance dramatically. 17) The data on this specification sheet is applicable when LCD module is placed in landscape position. 18) Continuous displaying fixed pattern may induce image sticking. It ’s recommended to use screen saver or shuffle content periodically if fixed pattern is displayed on the screen.
G150XG01 V1 rev. 0.0 G150XG01 V1 2. General Description G150XG01 V1 is a Color Active Matrix Liquid Crystal Display composed of a TFT-LCD display, a driver circuit, and a backlight system. The screen format is intended to support XGA (1024(H) x 768(V)) screen and 16.2M (RGB 8-bits) or 262k colors (RGB 6-bits). All input signals are LVDS interface compatible. Inverter card of backlight is not included. All design rules of this module can correspond to PSWG standard. G150XG01 V1 is designed for industrial display applications.
2.1 Display Characteristics
The following items are characteristics summary on the table under 25 ℃ condition: Items Unit Specifications Screen Diagonal [inch] 15 Active Area [mm] 304.128(H) x 228.096(V) Pixels H x V 1024x3(RGB) x 768 Pixel Pitch [mm] 0.297 x 0.297 Pixel Arrangement R.G.B. Vertical Stripe Display Mode TN, Normally White Nominal Input Voltage VDD [Volt] 3.3 typ. Typical Power Consumption [Watt] 8.9 ( 64 Gray Bar Pattern , exclude inverter) Weight [Grams] 1100g (typ.) Physical Size [mm] 326.5(H)x 253.5(V) x 12.0(D) (typ.) Electrical Interface 1 channel LVDS Surface Treatment Anti-glare, Hardness 3H Support Color 16.2M / 262K colors Temperature Range Operating Storage (Non-Operating) [oC] [oC] 0 to +65 (+65 oC as panel surface temperature) -20 to +65 RoHS Compliance RoHS Compliance
G150XG01 V1 rev. 0.0 G150XG01 V1
2.2 Optical Characteristics
The optical characteristics are measured under stable conditions at 25℃ (Room Temperature): Item Unit Conditions Min. Typ. Max. Note White Luminance [cd/m2] IRCFL= 5.5mA (center point) 300 350 - 1 Uniformity % 9 Points 75 80 - 1, 2, 3 Contrast Ratio 400 700 - 4 Cross talk % - 1.2 1.5 5 [msec] Rising - 5.7 [msec] Falling - 2.3 Response Time [msec] Raising + Falling - 8 [degree] [degree] Horizontal (Right) CR = 10 (Left) - Viewing Angle [degree] [degree] Vertical (Upper) CR = 10 (Lower) Red x 0.612 0.642 0.672 Red y 0.307 0.337 0.367 Green x 0.276 0.306 0.336 Green y 0.551 0.581 0.611 Blue x 0.114 0.144 0.174 Blue y 0.071 0.101 0.131 White x 0.283 0.313 0.343 Color / Chromaticity Coordinates (CIE 1931) White y 0.299 0.329 0.359 Note 1: Measurement method Equipment Pattern Generator, Power Supply, Digital Voltmeter, Luminance meter (SR_3 or equivalent) Aperture 1with 50cm viewing distanc∘ e Test Point Center Environment < 1 lux LCD Module SR_3 or equivalent Measuring distance Module Driving Equipment
G150XG01 V1 rev. 0.0 G150XG01 V1 Note 2: Definition of 9 points position (Display active area : 304.128(H) x 228.096(V)) Note 3: The luminance uniformity of 9 points is defined by dividing the minimum luminance values by the maximum test point luminance Note 4： Definition of contrast ratio (CR): Note 5： Definition of cross talk (CT) CT = | YB – YA | / YA × 100 (%) Where YA = Luminance of measured location without gray level 0 pattern (cd/m2) YB = Luminance of measured location with gray level 0 pattern (cd/m2) Minimum Brightness of nine points δW9 = Maximum Brightness of nine points Contrast ratio (CR)= Brightness on the “White” state Brightness on the “Black” state 50 % 90 % 90 % 50 % 10 % 10 % 1/6 A B 2/3 1/3 184 gray level
G150XG01 V1 rev. 0.0 G150XG01 V1 Note 6: Definition of response time: The output signals of photo detector are measured when the input signals are changed from “White” to “Black” (falling time) and from “Black” to “White” (rising time), respectively. The response time interval is between 10% and 90% of amplitudes. Please refer to the figure as below. Note 7: Definition of viewing angle Viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 ° horizontal and 180° ≧ vertical range (off-normal viewing angles). The 180° viewing angle range is broken down as below: 90° (θ) horizontal left and right, and 90° (Φ) vertical high (up) and low (down). The measurement direction is typically perpendicular to the display surface with the screen rotated to its center to develop the desired measurement viewing angle. 100 Optical response White Black White Tf Tr Optical response White Black White Tr
G150XG01 V1 rev. 0.0 G150XG01 V1 3. Functional Block Diagram The following diagram shows the functional block of the 15 inch color TFT/LCD module: 3804-F20N-06R / MSB240420E JST-BHR-03VS-1 Mating Type: HRS DF14-20S-1.25C SM02(8.0)B-BHS-1-TB
2 CCFL
+ 3.3V TFT-LCD 1024(3)*768 Pixels Y-Driver IC G768 D1 D3072 Gate Driver IC X-Driver IC Source Driver IC DC/DC Converter Gamma Correction
G150XG01 V1 rev. 0.0 G150XG01 V1 4. Absolute Maximum Ratings
4.1 Absolute Ratings of TFT LCD Module
Logic/LCD Drive Vin 0.3 +3.6 [Volt]
4.2 Absolute Ratings of Environment
Operating Temperature TOP 0 +60 [ oC] Operation Humidity HOP 8 90 [%RH] Storage Temperature TST -20 +65 [ oC] Storage Humidity HST 8 90 [%RH] Note: Maximum Wet-Bulb should be 39 and no condensation. ℃ T=40°C, H=95% T=65°C, H=27.9%
G150XG01 V1 rev. 0.0 G150XG01 V1 5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Symbol Parameter Min Typ Max Units Remark VDD Logic/LCD Drive Voltage 3.0 3.3 3.6 [Volt] ±10% IDD VDD Current - 550 660 [mA]
64 Gray Bar Pattern
(VDD=3.3V, at 60Hz) Irush LCD Inrush Current - - 3 [A] Note 1 PDD VDD Power - 1.9 2.2 [Watt] (VDD=3.3V, at 60Hz) Note 1: Measurement condition: AO6402 G D2S AO6402 G D2 S 1uF/16V 1uF/25V 0.01uF/25V VR1 47K +12.0V VCC SW1 SW MAG-SPST 1 2 (High to Low) Control Signal (LCD Module Input) +3.3V 47K 90% 10% VDD rising time 3.3V 470 us VDD
64 Gray pattern
G150XG01 V1 rev. 0.0 G150XG01 V1
5.1.2 Signal Electrical Characteristics
Input signals shall be low or Hi-Z state when VDD is off. Note: LVDS Signal Waveform. Symbol Item Min. Typ. Max. Unit Remark VTH Differential Input High Threshold - - 100 [mV] VCM=1.2V VTL Differential Input Low Threshold -100 - - [mV] VCM=1.2V ｜VID｜ Input Differential Voltage 100 400 600 [mV] VICM Differential Input Common Mode Voltage 1.1 1.45 [V] VTH/VTL=±100mV
G150XG01 V1 rev. 0.0 G150XG01 V1
5.2 Backlight Unit
5.2.1 Parameter guideline for CCFL
Following characteristics are measured under a stable condition using an inverter at 25 (Room Temperature):℃ Symbol Parameter Min. Typ. Max. Unit Remark IRCFL CCFL operation range 2.5 5.5 6.5 [mA] rms (Ta=25oC) Note 1 FCFL CCFL Frequency 40 46 65 [KHz] (Ta=25 oC) Note 2 ViCFL (0oC) (reference) CCFL Ignition Voltage - 1180 1480 [Volt] rms (Ta= 0oC) ViCFL (25oC) (reference) CCFL Ignition Voltage - 910 1140 [Volt] rms (Ta=25oC) VCFL CCFL Discharge Voltage 567 630 693 [Volt] rms (Ta=25oC) Note 3 IRCFL=5.5mA VCFL = Typ±10% PCFL CCFL Power consumption (inverter excluded) - 6.93 - [Watt] (Ta=25oC) Note 3 IRCFL=5.5mA Lamp Life 50,000 - Hrs (Ta=25oC) Note 4 IRCFL = 5.5mA Note 1: IRCFL is defined as the return current of an inverter. (In Figure. 1) (Figure. 1: Measurement of return current) A stable IRCFL is a current without flicker or biasing waveform provided by inverter that ensures the backlight perform to its specification. The ideal sine waveform should be symmetric in positive and negative polarities and the asymmetry rate of the inverter waveform should be below 10%. It is recommended to use the inverter with detection circuit to avoid overvoltage, overcurrent, or mismatching waveform. The purpose is to avoid current flow into only one of the lamps when the other one is not in operation. Note 2: CCFL frequency should be carefully determined to avoid interference between inverter and TFT LCD. Higher frequency will induce higher leakage current and further impact lamp life. Note 3: Calculator value for reference (IRCFLxVCFLx2=PCFL). Note 4: The definition of lamp life means when any of following conditions happen: a) Luminance falls to 50% or less of the initial value. b) Normal lighting is no more available (flickering, pink lighting, no lighting, etc.) c) Lamp voltage or lighting start voltage exceeds the specified value. Note 5: The display is with dual lamp design, and the CCFL current in above table refers to each lamp Inverter Lamp Hi Lo mA
G150XG01 V1 rev. 0.0 G150XG01 V1 6. Signal Characteristic
6.1 Pixel Format Image
Following figure shows the relationship between input signal and LCD pixel format.
6.2 Scanning Direction
The following figures show the image seen from the front view. The arrow indicates the direction of scan. Fig. 1 Normal scan (Pin4, REV = Low or NC) Fig. 2 Reverse scan (Pin4, REV = High)
G150XG01 V1 rev. 0.0 G150XG01 V1
6.3 Signal Description
The module using a pair of LVDS receiver SN75LVDS82(Texas Instruments) or compatible. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS83(negative edge sampling) or compatible. The first LVDS port(RxOxxx) transmits odd pixels while the second LVDS port(RxExxx) transmits even pixels. 3804-F20N-06R (E&T) / MSB240420E(STM) Pin No. Symbol Description 1 VDD Power Supply, 3.3V (typical) 2 VDD Power Supply, 3.3V (typical)
3 VSS Ground
4 REV Reverse Scan selection *.Note1
5 Rin0- - LVDS differential data input (R0-R5, G0)
6 Rin0+ + LVDS differential data input (R0-R5, G0)
7 VSS Ground
8 Rin1- - LVDS differential data input (G1-G5, B0-B1)
9 Rin1+ + LVDS differential data input (G1-G5, B0-B1)
10 VSS Ground
11 Rin2- - LVDS differential data input (B2-B5, HS, VS, DE)
12 Rin2+ + LVDS differential data input (B2-B5, HS, VS, DE)
13 VSS Ground
14 ClkIN- - LVDS differential clock input
15 ClkIN+ + LVDS differential clock input
16 GND Ground
17 Rin3- - LVDS differential data input (R6-R7, G6-G7,B6-B7)
18 Rin3+ - LVDS differential data input (R6-R7, G6-G7,B6-B7)
19 VSS Ground
20 SEL68 Selection for 6 bits/8bits LVDS data input *Note1
Note 1: Input signals shall be in low status when VDD is off.
G150XG01 V1 rev. 0.0 G150XG01 V1
6.4 The Input Data Format
6.4.1 SEL68
SEL68 = ”High” or “NC” for 6 bits LVDS Input G0 R5R4R3R2 R1R0 DEVSHS B5B4 B3B2 B1B0 G5G4G3 G2G1 RxCLKIN RxIN1 RxIN2 RxIN3 SEL68 = “Low” for 8 bits LVDS Input G0 R5R4R3R2 R1R0 RSV B7B6 G7G6 R7R6 DEVSHS B5B4 B3B2 B1B0 G5G4G3 G2G1 RxCLKIN RxIN1 RxIN2 RxIN3 RxIN4 Note1: Please follow PSWG. Note2: R/G/B data 7:MSB, R/G/B data 0:LSB Signal Name Description Remark Red Data 7 Red Data 6 Red Data 5 Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 Red-pixel Data For 8Bits LVDS input MSB: R7 ; LSB: R0 For 6Bits LVDS input MSB: R5 ; LSB: R0 Green Data 7 Green Data 6 Green Data 5 Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 Green-pixel Data For 8Bits LVDS input MSB: G7 ; LSB: G0 For 6Bits LVDS input MSB: G5 ; LSB: G0 Blue Data 7 Blue Data 6 Blue Data 5 Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 Blue-pixel Data For 8Bits LVDS input MSB: B7 ; LSB: B0 For 6Bits LVDS input MSB: B5 ; LSB: B0 RxCLKIN LVDS Data Clock DE Data Enable Signal When the signal is high, the pixel data shall be valid to be displayed. VS Vertical Synchronous Signal HS Horizontal Synchronous Signal Note: Output signals from any system shall be low or Hi-Z state when VDD is off.
G150XG01 V1 rev. 0.0 G150XG01 V1
6.5 Interface Timing
6.5.1 Timing Characteristics
Signal Parameter Symbol Min. Typ. Max. Unit Clock Timing Clock frequency 1/ T Clock 50 65 81 MHz Period T V 776 806 1024 Active T VD 768 768 768 Vsync Timing Vertical Section Blanking TVB 8 38 256 TLine Period T H 1054 1344 2048 Active T HD 1024 1024 1024 Hsync Timing Horizontal Section Blanking THB 30 320 1024 TClock Note: Frame rate is 60 Hz. Note: DE mode. Note : Typical value refer to VESA STANDARD
6.5.2 Input Timing Diagram
Input Timing Definition ( DE Mode) TCLOCK Input Data Pixel Pixel Pixel Pixel N-1 Pixel N Invaild Data Invaild Data Pixel
G150XG01 V1 rev. 0.0 G150XG01 V1
6.6 Power ON/OFF Sequence
VDD power and lamp on/off sequence is as below. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. Power ON/OFF sequence timing Value Parameter Min. Typ. Max. Units T1 0.5 - 10 ms T2 0 40 50 ms T3 200 - - ms T4 200 - - ms T5 0 16 50 ms T6 0 - 10 ms T7 1000 - - ms The above on/off sequence should be applied to avoid abnormal function in the display. Please make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. T7 T 5 T2 VALID DATA 10% 90% 10% 90% T6 Power Supply VDD LVDS Signal Backlight On
G150XG01 V1 rev. 0.0 G150XG01 V1 7. Connector & Pin Assignment Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components.
7.1 TFT LCD Module: LVDS Connector
Connector Name / Designation Signal Connector Manufacturer E&T or compatible Connector Model Number 3804-F20N-06R / MSB240420E Adaptable Plug HRS DF14-20S-1.25C Pin# Signal Name Pin# Signal Name
1 VDD 2 VDD
3 VSS 4 REV
5 Rin0- 6 Rin0+
7 VSS 8 Rin1-
9 Rin1+ 10 VSS
11 Rin2- 12 Rin2+
13 VSS 14 ClkIN-
15 ClkIN+ 16 GND
17 Rin3- 18 Rin3+
19 VSS 20 SEL68
G150XG01 V1 rev. 0.0 G150XG01 V1
7.1.1 Connector Illustration
G150XG01 V1 rev. 0.0 G150XG01 V1
7.2 Backlight Unit: Lamp Connector
Connector Name / Designation Lamp Connector Manufacturer JST or compatible Connector Model Number BHR-03VS-1 or compatible Mating Model Number SM02(8.0)B-BHS-1-TB or compatible
7.3 Lamp Connector Pin Assignment
Pin# Symbol Cable color Signal Name
1 HV Pink Lamp High Voltage
2 NC NC No Connection
3 LV White Ground
u Cable length: 140 ± 5 mm u Connector-output position: right side (front view) u Lamp assembly design shall be easy for replacement and repair
G150XG01 V1 rev. 0.0 G150XG01 V1 8. Reliability Test Criteria Items Required Condition Note Temperature Humidity Bias 50/℃80%,300 hours High Temperature Operation 60℃,300 hours Low Temperature Operation 0℃,300 hours Hot Storage 60,300 hours℃ Cold Storage -20,300 hours℃ Thermal Shock Test -20/30 min ,60/30 min ,100cycles℃℃ Shock Test (Non-Operating) 50G,20ms,Half-sine wave,( ±X, ±Y, ±Z) Vibration Test (Non-Operating) 30 mins/axis (X, Y, Z) On/off test On/10 sec, Off/10 sec, 30,000 cycles ESD Contact Discharge: ± 8KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point Air Discharge: ± 15KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point Note 1 Note1: According to EN61000-4-2, ESD class B: Some performance degradation allowed. No data lost . Self-recoverable. No hardware failures.
G150XG01 V1 rev. 0.0 G150XG01 V1 9. Mechanical Characteristics
9.1 LCM Front View and Rear View
G150XG01 V1 rev. 0.0 G150XG01 V1
9.2 LCM Outline Dimension (Front View)
G150XG01 V1 rev. 0.0 G150XG01 V1
9.3 LCM Outline Dimension (Rear View)
G150XG01 V1 rev. 0.0 G150XG01 V1 10. Label and Packaging
10.1 Shipping Label (on the rear side of TFT-LCD display)
10.2 Carton Package
Max capacity: 15 TFT-LCD module per carton (15pcs * 1 layers) Max weight: 20 kg per carton Outside dimension of carton: 375(L)mm* 430(W)mm* 360(H)mm
G150XG01 V1 rev. 0.0 G150XG01 V1
11 Safety
11.1 Sharp Edge Requirements
There will be no sharp edges or comers on the display assembly that could cause injury.
11.2 Materials
11.2.1 Toxicity
There will be no carcinogenic materials used anywhere in the display module. If toxic materials are used, they will be reviewed and approved by the responsible AUO toxicologist.
11.2.2 Flammability
All components including electrical components that do not meet the flammability grade UL94-V1 in the module will complete the flammability rating exception approval process. The printed circuit board will be made from material rated 94-V1 or better. The actual UL flammability rating will be printed on the printed circuit board.
11.3 Capacitors
If any polarized capacitors are used in the display assembly, provisions will be made to keep them from being inserted backwards.
11.4 National Test Lab Requirement
The display module will satisfy all requirements for compliance to: UL 1950, First Edition U.S.A. Information Technology Equipment