G084SN03 | DigiCamel IC Datasheet

Online Datasheet

Read G084SN03 online.

G084SN03V.0 AUO | Alldatasheet

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 24

Technical content

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 Version: 0.3 Total Pages: 23 Date: 2005/8/29 Product Functional Specification 8.4 inch SVGA Color TFT LCD Module Model Name: G084SN03 V.0 (u) Preliminary Specification ( ) Final Specification Note: This Specification is subject to change without notice.

2.1 Display Characteristics

2.2 Functional Block Diagram

5.1 Connectors

5.2 Signal Pin

5.3 Signal Description

5.4 Signal Electrical Characteristics

5.5 Signal for Lamp Connector

8.1 Timing Characteristics

8.2 Timing Definition

8.3 Timing Chart

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 II. Record of Revision Version and Date Page Old Description New Description Remark 0.1 2005/05/20 All N/A First draft 0.2 2005/08/09 5 N/A Add a discription of RoHs 0.3 2005/08/29 8 View angle 60/60/60/40 View angle 65/65/65/45

1.0 Handing Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnection from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the interface Connector of the TFT module. 11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module may be damaged. 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module should be supplied by power complied with requirements of Limited Power Source, or be applied exemption. 14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit. Do not connect the CFL in Hazardous Voltage Circuit.

2.0 General Description

This specification applies to the 8.4 inch color TFT LCD module B084SN03 V.0. This module is designed for General Display. The screen format is intended to support the SVGA (800(H) x 600(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface compatible. The module does not contain an inverter card for backlight. This is an RoHs product. The following items are characteristics summary on the table under 25℃ condition ： Items Unit Specifications Screen Diagonal [mm] 213.4 ( 8.4 ”) Active Area [mm] 170.4(H) x 127.8(V) Pixel H x V 800(x3) x 600 Pixel Pitch [mm] 0.213(H) x 0.213(V) Pixel Arrangement R.G.B. Vertical Stripe Display Mode Normally White Typical White Luminance (ICFL=4.6 mA) [cd/m 2] 220 Typ. (center) Contrast Ratio 500：1 Typ. Optical Rise Time/Fall Time [msec] 10/25 Typ. Nominal Input Voltage VDD [Volt] +3.3 Typ. Typical Power Consumption (VDD line + VCFL line) [Watt] 3.3 Typ Weight [Grams] 215 ±10 Physical Size [mm] 203.0(W) x 142.5(H) x 5.7(D) Electrical Interface 1 channel LVDS Support Color Native 262K colors (RGB 6-bit driver) Temperature Range Operating Storage(Shipping) [℃] [℃] 0 to +50 -20 to +60

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 The following diagram shows the functional block of the 8.4 inches Color TFT LCD Module：

3.0 Absolute Maximum Ratings

Absolute maximum ratings of the module is as follows： Item Symbol Min Max Unit Conditions Logic/LCD Drive Voltage VDD -0.3 +4.0 [Volt] Input Voltage of Signal Vin -0.3 VDD+0.3 [Volt] CCFL Current ICFL 3 6 [mA] rms CCFL lgnition Voltage Vs 441 539 Vrms Operating Temperature TOP 0 +50 [℃] Note1 Operating Humidity HOP 8 90 [%RH] Note1 Storage Temperature TST -20 +60 [℃] Note1 Storage Humidity HST 5 90 [%RH] Note1 Vibration 1.0, 10-500 [G, Hz] 2hr/axis X,Y,Z Shock 220, 2 [G, ms] Half sine wave Note1：Maximum Wet-Bulb should be 39℃ and no condensation.

4.0 Optical Characteristics

The optical characteristics are measured under stable conditions as follows under 25℃ condition ： Item Unit Conditions Min. Typ. Max. Horizontal (Right) K = 10 (Left) － Viewing Angle K：Contrast ratio [degree] [degree] [degree] [degree] Vertical (Upper) K = 10 (Lower) － 65 White Uniformity 9 Points －－ 1.6 Contrast ratio θ= 0° 300 500 － Rising － 10 20 Response Time (Room Temp) [msec] [msec] Falling － 25 30 Red x 0.540 0.570 0.600 Red y 0.290 0.320 0.350 Green x 0.290 0.320 0.350 Green y 0.530 0.560 0.590 Blue x 0.120 0.150 0.180 Blue y 0.090 0.120 0.150 White x 0.280 0.310 0.340 Color Chromaticity Coordinates(CIE) White y 0.300 0.330 0.360 White Luminance (ICFL 4.6 mA) [cd/m ] θ= 0° 200 (Center) 220 (Center)

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 Note 1: Definition of white uniformity: White uniformity is calculated with the following formula. Luminance are measured at the following nine points (1~9). δW Maximum Brightness of nine points Minimum Brightness of nine points

5.0 Signal Interface

Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation For Signal Connector Manufacturer HIROSE Type / Part Number HRS DF 19K-20P-1H Mating Connector / Part Number HRS DF19G-20S-1C (WIRE TYPE)) Mating Connector / Part Number HRS DF19-20S-1F (FPC TYPE) Connector Name / Designation For Lamp Connector Manufacturer JST Type / Part Number BHSR-02VS-1 Mating Connector / Part Number SM02B-BHSS-1-TB Pin No. Signal Name Pin No. Signal Name

1 VDD 2 VDD

3 GND 4 GND

5 RxIN0- 6 RxIN0+

7 GND 8 RxIN1-

9 RxIN1+ 10 GND

11 RxIN2- 12 RxIN2+

13 GND 14 CKIN-

15 CKIN+ 16 GND

17 NC 18 NC

19 GND 20 GND

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 The module using a LVDS receiver. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS84 (negative edge sampling) or compatible. Note：Input signals shall be low or Hi-Z state when VDD is off. Signal Name Description RxIN0-, RxIN0+ LVDS differential data input (Red0-Red5, Green0) RxIN1-, RxIN1+ LVDS differential data input (Green1-Green5, Blue0-Blue1) RxIN2-, RxIN2+ LVDS differential data input (Blue2-Blue5, Hsync, Vsync, DE) CKIN-, CKIN+ LVDS differential clock input VDD +3.3V Power Supply GND Ground NC No Connection

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 Signal Name Description +RED5 +RED4 +RED3 +RED2 +RED1 +RED0 Red Data 5 (MSB) Red Data 4 Red Data 3 Red Data 2 Red Data 1 Red Data 0 (LSB) Red-pixel Data Red-pixel Data Each red pixel’s brightness data consists of these 6 bits pixel data. +GREEN5 +GREEN4 +GREEN3 +GREEN2 +GREEN1 +GREEN0 Green Data 5 (MSB) Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 (LSB) Green-pixel Data Green-pixel Data Each green pixel’s brightness data consists of these 6 bits pixel data. +BLUE5 +BLUE4 +BLUE3 +BLUE2 +BLUE1 +BLUE0 Blue Data 5 (MSB) Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 (LSB) Blue-pixel Data Blue-pixel Data Each blue pixel’s brightness data consists of these 6 bits pixel data. CLK Data Clock The typical frequency is 40MHz. The signal is used to strobe the pixel data and DE signals. All pixel data shall be valid at the falling edge when the DE signal is high. DE Display Timing This signal is strobed at the falling edge of CLK. When the signal is high, the pixel data shall be valid to be displayed. VSYNC Vertical Sync The signal is synchronized to CLK. HSYNC Horizontal Sync The signal is synchronized to CLK. Note：Output signals from any system shall be low or Hi-Z state when VDD is off.

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 Input signals shall be low or Hi-Z state when VDD is off. It is recommended to refer the specifications of SN75LVDS86(Texas Instruments) in detail. Signal electrical characteristics are as follows： Item Symbol Min. Typ. Max. Unit The differential level ｜VID｜ 0.1 - 0.6 V The common mode input voltage VIC - V The input setup time tsu 0.5 - - ns The input hold time thd 0.5 - - ns High-level input voltage V IAP 2.0 V Low-level input voltage V IAM 0.8 V Clock frequency CLK 31 68 MHz 2.4－︱VID︱︱VID︱

2 L CCFL power supply(GND) Cable color: White

6.0 Pixel Format Image

Following figure shows the relationship of the input signals and LCD pixel format： R G B R G B R G B R G B R G B R G B R G B R G B 1 2 799 800 1st Line 600th Line

7.0 Parameter guide line for CFL inverter

Parameter Min Typ Max Units Condition White Luminance 200 220 - Cd/m 2 CCFL current (ICFL) 3.0 4.6 - mArms Note1 CCFL Frequency (FCFL) 50 60 80 KHz Note4 CCFL Ignition Voltage (Vs) - - 1070(T=0℃) 820(T=25℃) Vrms Note3 CCFL Voltage (Reference) (VCFL) 441 490 539 Vrms Note1 CCFL Power consumption (PCFL) - 2.3 - W Note2 Lamp Life Time 10,000 20,000 - Hr Note1, 5 Note1：T=25℃ Note2：Inverter should be designed with the characteristic of lamp. When you are designing the inverter, the output voltage of the inverter should comply with the following conditions. (1). The area under the positive and negative cycles of the waveform of the lamp current and lamp voltage should be area symmetric (the symmetric ratio should be larger than 90%). (2). There should not be any spikes in the waveform. (3). The waveform should be sine wave as possible. (4). Lamp current should not exceed the maximum value within the operating temperature (It is prohibited to over the maximum lamp current even if operated in the non-guaranteed temperature). When lamp current is over the maximum value for a long time, it may cause fire. Therefore, it is recommend that the inverter should have the current limit circuit. Note3：The inverter open voltage should be designed larger than the lamp starting voltage at T=0 o C, otherwise backlight may be blinking for a moment after turning on or not be able to turn on. The open voltage should be measured after ballast capacitor. If an inverter has shutdown function it should keep its open voltage for longer than 1 second even if lamp connector is open. Note4：Lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. Therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. Note5：Brightness (ICFL=4.6mA) to be decreased to the 50% of the initial value.

8.0 Interface Timings

Basically, interface timing should match the VESA 800x600 /60Hz(VG901101) manufacturing guide line timing. (a) DE mode Item Symbol Min. Typ. Max. Unit Remark Clock frequency Fck 38 40 48 MHz Horizontal blanking Thb1 50 256 500 Clk Vertical blanking Tvb1 10 28 150 Th (b) HV mode Item Symbol Min. Typ. Max. Unit Remark Clock frequency Fck 38 40 48 MHz Hsync period Th 850 1056 1300 Clk Hsync pulse width Thw 10 128 - Clk Hsync front porch Thf 15 40 - Clk Hsync back porch Thb 10 88 - Clk Hsync blanking Thb1 50 256 500 Clk Vsync period Tv 610 628 750 Th Vsync pulse width Tvw 1 4 - Th Vsync front porch Tvf 0 1 - Th Vsync blanking Tvb1 10 28 150 Th Hsync/Vsync phase shift Tvpd 2 320 - Clk Item Symbol Value Unit Description Horizontal display start The 218 Clk After falling edge of Hsync, counting 218clk, then getting valid data from 219th clk ’s data. Vertical display start Tve 25 Th After falling edge of Vsync, counting 25th, then getting 26th Th ’s data.

(C) Copyright AU Optroncis, Inc. 2005 All Right Reserved. G084SN03 V.0 No Reproduction and Redistribution Allowed. 8/9 X,599 X,600 Invalid X,1 X,2 X,3 X,600 X,599 Invalid Tvbl Tvd 800,Y 1,Y 2,Y 3,Y 799,Y 800,Y invalid Thd Thbl (1 pixel / clock) invalid Tv Fck Th

9.0 Power Consumption

Input power specifications are as follows： Symbol Parameter Min Typ Max Units Condition VDD Logic/LCD Drive Voltage 3.0 3.3 3.6 V PDD VDD Power - 0.76 - W PDD Max VDD Power max - 0.86 - W IDD IDD Current - 230 - mArms Note 1 IDD Max IDD Current max - 260 310 mArms Note 2 VRP Power Ripple Voltage - 100 - mVp-p I RUSH Inrush Current - 1500 - mApeak Note 1: Effective value (mArms) at V CC = 3.3 V/25℃. Note 2:

10.0 Power ON/OFF Sequence

VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off.

11.0 Reliability Test Items

Test item Test Condition Remark High temperature storage 60℃, 300Hrs Note 1, 2, 3 Low temperature storage -20℃,300Hrs Note 1, 2, 3 High temperature & high humidity operation 40℃, 90%RH, 300Hrs (No condensation) Note 1, 2, 3 High temperature operation 50℃, 300Hrs Note 1, 2, 3 Low temperature operation 0℃, 300Hrs Note 1, 2, 3 Temperature cycling (non-operation) -20℃~60℃ 1H, 10mins, 1H, 5cycles Note 1, 2, 3 Electrostatic discharge (non-operation) 150 pF,150Ω,10kV,1 second, 9 position on the panel, 10 times each place Note 3 Vibration (non-operation) Sweep:1G, 10HZ ~ 500HZ ~ 10HZ /2.5min 2 hours for each direction X, Y, Z Note 1, 2, 3 Mechanical shock (non-operation) 50G/11ms, 220G/2ms, ±X, ±Y, ±Z once for each direction Note 1, 2, 3 Note 1: Evaluation should be tested after storage at room temperature for one hour. Note 2: There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. Note 3: Judgement: 1.Function OK. 2.No serious image quality degradation. Display quality The display quality of the color TFT-LCD module should be in compliance with the AUO ’s OQC inspection standard. Handling precaution The Handling of the TFT-LCD should be in compliance with the AUO ’s handling principle standard.

12.0 Packing Dimension:

Max. Capacity : 30 LCD Modules/Carton. NOTE : 2. Max. Weight : 12 Kg/Carton. 3. Meas : 600 mm*353mm*210mm. Anti-Static Bag LCD Module EPP Cushion Carton

12.1 Label:

13.0 Mechanical Characteristic

Product Information

G084SN03 specifications and overview.

Summary

8.4 inch SVGA Color TFT LCD Module

Description

8.4 inch SVGA Color TFT LCD Module

Source title G084SN03 Datasheet(PDF) - AU Optronics Corp.,

Related Parts

More parts from the same family.

Browse manufacturer