FX579

FX579 CMLMICRO | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 23

Technical content

Datasheet sections

• 1.0 Features
• 1.1 Brief Description
• 1.2 Block Diagram
• 1.3 Signal List
• 1.4 External Components
• 1.5 General Description
• 1.6 Application Notes
• 1.7 Performance Specification

CML Semiconductor Products Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited D/579/4 Sept 1995

1.0 Features Provisional Issue

• • Half Duplex GMSK Modem for FM Radio Data Links
• • Acquire Pin to assist with the acquisition of Rx Data signals
• • Pin-Programmable Rx/Tx Data Rates: 4k to 20 kbits/sec at VDD = 3.0V 4k to 40 kbits/sec at VDD = 5.0V
• • Serial Data Interface with Rx/Tx Data Clock
• • Low Operating Power: < 2mA at 3.0V, < 4mA at 5.0V Non-DSP solution
• • Telemetry, Wireless Alarms, PC, Laptop and Printer Comms, WAN and LAN and General Purpose Data Applications
• • 16-Pin Package with few External Components
• • Low Cost

1.1 Brief Description

The FX579 is a single chip, low cost, low current integrated circuit that performs the baseband functions of a half duplex GMSK modem and is intended for use in FM radio data links. This general purpose modem is suitable for data rates in the region of 4 to 40 kbits/sec, at a BT of 0.3 or 0.5. The Tx and Rx data lines share a common pin and data is synchronised to a Tx/Rx data clock generated by the modem. A single ACQUIRE line is provided to assist with acquisition of Rx data signals.

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 3 D/579/4

1.2 Block Diagram

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 4 D/579/4

1.3 Signal List

Pin No. Name Type 1 XTALN O/P The output of the on-chip oscillator.

2 XTAL/CLK I/P The input to the on-chip oscillator for an external

Xtal circuit or clock.

3 CLKDIVA I/P ) Two logic level inputs that control the internal

4 CLKDIVB I/P

) clock divider and hence the transmit and ) receive data rate (See Table 1).

5 ACQUIRE I/P A logic "1" applied to this input will set the Rx

level measurement and Rx clock extraction circuitry to 'acquire' mode.

6 VBIAS O/P The internal circuitry bias line, held at ½ VDD ,

this pin must be decoupled to VSS by a capacitor mounted close to the pin.

7 RXIN I/P The Rx signal input from the radio's discriminator

via suitable signal and dc level adjustment. In Rx this pin is internally held at ½ V DD . 8 VSS Power Negative supply rail. Signal ground. 9 TXOP O/P The Tx signal output. This signal should be applied to an external RC before being applied to the radio modulator.

10 BT I/P A logic level input to select the modem 'BT' (the

ratio of the Tx filter -3dB frequency to the bit rate). A logic "1" sets the modem to a BT of 0.5, a logic "0" to a BT of 0.3. DOC1 DOC2 O/P O/P Two pins used by the modem's Rx level measurement circuitry. A capacitor should be connected from each pin to VSS .

13 TXRXN I/P A logic level applied to this pin determines

whether the modem operates in Tx or Rx mode. A logic "1" sets Tx mode. A logic "0" sets Rx mode.

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 5 D/579/4 Package D4 Signal Description Pin No. Name Type

14 DATAIO BI A bidirectional pin that is used for inputting Tx

data or outputting Rx data.

15 DATACLK O/P This pin outputs either the Tx DATACLK in Tx

mode or the Rx DATACLK in Rx mode. 16 VDD Power Positive supply rail. A single stable power supply is required. Levels and voltages within this modem are dependent upon this supply. This pin should be decoupled to V SS by a capacitor mounted close to the pin. Notes: I/P = Input O/P = Output BI = Bidrectional

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 6 D/579/4

1.4 External Components

Component Value Tolerance Component Value Tolerance R1 1M Ω ±10% C3 Note 2 ±20% R2 Note 1 ± 5% C4 Note 2 ±20% X1 Note 3 C5 Note 3 C1 100nF ±20% C6 Note 3 C2 100nF ±20% C7 Note 1 ±5% Notes: 1. The RC network formed by R2 and C7 is required between the TXOP pin and the input to the modulator. This network, which can form part of any dc level shifting and gain adjustment circuitry, forms an important part of the transmit signal filtering. The ground connection to the capacitor C7, should be positioned to give maximum attenuation of high frequency noise into the modulator. The component values should be chosen so that the product of the resistance (Ohms) and the capacitance (Farads) is: BT of 0.3 = 0.34/bit rate (bits/sec) BT of 0.5 = 0.21/bit rate (bits/sec) with suitable values for common bit rates being: R2 C7 4000 bits/secBT = 0.3 180.0k Ω 470pF 4800 bits/secBT = 0.5 91.0kΩ 470pF 8000 bits/secBT = 0.3 91.0kΩ 470pF 9600 bits/secBT = 0.5 47.0kΩ 470pF 19 200 bits/secBT = 0.5 91.0kΩ 120pF 32 000 bits/secBT = 0.3 47.0kΩ 220pF 32 000 bits/secBT = 0.5 47.0kΩ 150pF 38 400 bits/secBT = 0.3 47.0kΩ 180pF 38 400 bits/secBT = 0.5 47.0kΩ 120pF Note that in all cases the value of R2 should not be less than 47.0kΩ and that the calculated value of C7 includes calculated parasitic capacitances. 2. C3 and C4 should both be 15.0nF for a data rate of 8kbits/sec, and inversely proportional to the data rate for other data rates, e.g. 30.0nF at 4kbits/sec, 3.0nF at 40kbits/sec. 3. The FX579 can operate correctly with Xtal/Clock frequencies between 1.0MHz and 6.5MHz (VDD = 5V) and up to 5.0MHz (VDD = 3V). The value chosen for C5 and C6 should be suitable for the applied VDD and the frequency of X1 and include stray capacitance. As a guide:At 5 Volts, C5 = C6 = 33.0pF at 1.0MHz falling to 18pF at 6.5MHz At 3 Volts, C5 = C6 = 33.0pF at 1.0MHz falling to 18pF at 5MHz The equivalent series resistance of X1 should be less than 2.0kΩ at 1MHz falling to 150Ω at the maximum frequency. Stray capacitance on the Xtal/Clock circuit pins must be minimised. Figure 2 Recommended External Components (SOIC Package)

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 7 D/579/4

1.5 General Description

1.5.1 Overall Function Description

The FX579 is a single chip processor that performs the baseband function of a half duplex modem employing Gaussian minimum shift keying (GMSK) modulation. Data rates of 4kbits/sec to 40kbits/sec and the choice of BT of 0.3 or 0.5 are pin programmable functions to suit radio data channel bandwidth requirements. Figure 3 shows how the modem is used in a typical radio application. In transmit mode data at the DATAIO pin is retimed with the Tx clock (output at the DATACLK pin) before being level shifted and passed through the GMSK Gaussian filter to the TXOP pin. An external RC network forms part of this filter and is required, in association with any signal and dc level adjustment, for driving the radio's frequency modulator. In receive mode, data from the radio's frequency discriminator, having been adjusted externally for signal and dc levels to provide a nominal input level of 1V pk-pk centred around ½ V DD (VDD = 5V), is then processed to produce data at the DATAIO pin in binary form, together with a regenerated clock at the DATACLK pin. Acquisition and lock of Rx data signals is made easier and faster by the use of an ACQUIRE input which can be set by the system µController as required. The FX579 features a low current analogue/digital ASIC process offering significantly lower current consumption than DSP technology. This CMOS microcircuit is available in a 16-pin small outline (SOIC) package.

1.5.2 Description of Blocks and Signal Path

(Reference Block Diagram Figure 1). Power Supply Circuits These circuits produce the necessary internal voltage levels. Note that V DD and VBIAS should be decoupled to VSS as shown. Clock Oscillator and Divider The transmit and (nominal) receive data rates are determined by division of the frequency present at the XTALN pin, which may be generated by the on-chip Xtal oscillator or come from an external source. Any Xtal/Clock frequency in the range 1.0MHz to 5.0MHz (V DD = 3.0V) or 1.0MHz to 6.5MHz (VDD = 5.0V) may be used depending upon the desired data rate. A division ratio to facilitate data rate setting is controlled by the logic level inputs on the CLKDIVA and CLKDIVB pins and is shown in Table 1 together with examples of how various 'standard' data rates may be derived from common Xtal frequencies. Data Rate = Xtal or Clock Frequency Division Ratio Division ratio = Xtal Clock Frequency CLKDIVA CLKDIVB Xtal frequency ÷ Data rate 4.096 (12.288/3) 4.9152 2.048 (6.144/3) 2.4576 (12.288/5) 0 0 128 32 000 38 400 16 000 19 200 0 1 256 16 000 19 200 8000 9600 1 0 512 8000 9600 4000 4800 1 1 1024 4000 4800 - - Table 1 Clock and Data Rates (in MHz and bits/sec, respectively)

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 11 D/579/4 Receive Signal Path The function of the Rx circuitry is to: a) Accept an incoming signal from the radio's frequency discriminator at a defined level via suitable external signal and dc level adjustment b) Clean the signal by filtering c) Provide dc level thresholds for clock and data extraction d) Provide clock timing information for data extraction and external circuits e) Provide Rx data as an output in binary form The output of the radio receiver's frequency discriminator after suitable external signal and level adjustment is applied to the RXIN pin. With VDD = 5V, nominal input level when receiving a continuous "1111000011110000..." data pattern should be 1V pk-pk (level is proportional to VDD ) centred around ½ V DD . Positive going signal excursions about VBIAS at RXIN will produce a logic "1" on the DATAIO pin, negative going signal excursions will produce a logic "0". The signal is then applied to the low pass Rx filter, which has a -3dB corner frequency of 0.56 times the data bit rate, before being applied to the Level Measuring and Clock and Data Extraction blocks. Level Measuring Circuit The 'Level Measuring' block consists of two voltage detectors one of which measures the amplitude of the 'positive' peaks of the received signal, while the other measures the 'negative' peaks. These detectors use the external capacitors connected to the DOC1 and DOC2 pins to form voltage hold or integrator circuits. Results of the two measurements are then processed within the modem to establish the optimum dc level decision thresholds for the Clock and Data Extraction circuits, depending on the received signal amplitude, BT and any dc offset present. The receive circuits operate in several control modes as defined by the logic level applied to the acquire pin. These are explained later - See 'Acquire Sequence'. Rx Clock Extraction Block The 'Rx Clock Extraction' circuit is based on a zero crossing tracking loop which uses a multi resolution digital phase locked loop (PLL). The wide bandwidth mode allows for fast initial phase acquisition. Eight good zero crossings are required for correct operation. The highest timing resolution is obtained when the PLL is in its narrow bandwidth mode. This mode of operation yields the least amount of phase jitter, which is responsible for the associated bit error rate (BER) performance degradation. The PLL operating mode is defined by the logic level applied to the ACQUIRE pin - See 'Acquire Sequence'. Rx Data Extraction Block The 'Rx Data Extraction' circuit decides whether each received bit is a "1" or "0" by sampling the received signal, after filtering, in the middle of each bit period and comparing the sampled voltage against a threshold derived from the 'Level Measuring' circuit. This threshold is adapted from bit to bit to compensate for intersymbol interference depending on the chosen BT. The extracted data is output from the DATAIO pin and should be sampled externally on the rising edge of the received data clock.

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 13 D/579/4 Figure 7 Receive Control Mode Diagram

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 14 D/579/4 ACQUIRE Pin Rx Level Measurement Mode PLL Mode "0" to "1" Clamp Narrow → Wide Bandwidth "1" Lossy Peak Detect Wide Bandwidth "0" Peak Averaging Narrow Bandwidth Rx Level Measurement Clamp: Operates for a minimum of two bit times, maximum three bit times, after a "0" to "1" transition of the ACQUIRE input. The external DOC capacitors are rapidly charged towards the input signal level, with the charge time constant being of the order of 0.5 bit time. Rx Level Measurement Lossy Peak Detect: The detectors rapidly capture the +ve and -ve going signal peaks of the Rx filter output signal, these peaks being stored on the external DOC capacitors. The detectors operate in this mode whenever ACQUIRE is at a logic "1", except for the initial Clamp period. Rx Level Measurement Peak Averaging: Provides a slower but more accurate measurement of the signal peak amplitudes. This operating mode depends on the PLL circuitry being in lock. PLL Wide Bandwidth: Sets the PLL bandwidth wide enough to allow a lock to the received signal in 8 zero crossings. This mode will operate as long as ACQUIRE is at logic "1". PLL Narrow Bandwidth: The correction applied to the extracted clock is limited to a maximum of ± 1/16th bit period for every 4 zero crossings received. The PLL operates in this mode whenever the ACQUIRE input is set to logic "0". Table 3 Receive Operating Modes Rx Data Formats The receive section of the FX579 works best with data which has a reasonably 'random' structure, i.e. the data should contain approximately the same number of 'ones' as 'zeroes' with no long sequences (> 100 bits) of consecutive 'ones' or 'zeroes'. Also, long sequences (>100 bits) of patterns without "11" and "00" should be avoided. For this reason, it is recommended that data is scrambled in some manner before transmission, for example by 'exclusive-ORing' with the output of a binary pseudorandom pattern generator. Where data is transmitted in bursts, each burst should be preceded by a preamble designed to allow the receive modem to establish timing and level lock as quickly as possible. This preamble should be at least 16 bits long, and should preferably consist of alternating pairs of "1"s and "0"s i.e. circuits, although performance is better with BT = 0.5 than with BT = 0.3.

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 15 D/579/4 Figure 8 Tx/Rx Data and Clock Timings

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 16 D/579/4 Tx/Rx Switching (Refer to Figure 8) Rx to Tx Transition - following a "0" to "1" transition on the TXRXN input: a) If DATACLK is at a logic "1" it will go to a logic "0" (t1 max = 1µs), or if at logic "0" will stay low. It will then remain at "0" for a minimum of 2 bit times, maximum of 3 bit times, before the first +ve transmit clock edge occurs. b) The DATAIO line will go to a high impedance state ready for Tx data to be applied (t2 max = 1µs). Data on the DATAIO line should be set up and ready for when the first +ve transmit clock edge occurs. This edge will clock the first bit of data into the transmit filter. Succeeding -ve clock edges may be used by the µController to ensure that data is always set up when +ve edges occur. c) TXOP is opened to the transmit path upon occurrence of the first +ve clock edge. Due to the delay of the filter, the centre of Bit 1 will appear at the pin a maximum of 2 bit times (BT = 0.5) or 2.5 bit times (BT = 0.3) later. d) At the end of a message the transmit output will remain in the state of the last bit sent. e) If a long period of unmodulated carrier is required before a message (approximately 10ms as on MOBITEX), then the radio's transmitter should be keyed up with the FX579 modem still in Rx mode. Tx to Rx Transition - following a "1" to "0" transition on the TXRXN input: a) DATACLK continues at the nominal bit rate in a free-running mode until locked to a receive signal, e.g. after a satisfactory ACQUIRE sequence. b) The buffer driving the TXOP pin is immediately connected to VBIAS. c) The DATAIO line immediately goes low impedance and starts sending Rx data. d) There is a 3-bit delay in the receive path before RXIN input data can appear at the DATAIO pin.

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 17 D/579/4

1.6 Application Notes

Radio Channel Requirements To achieve legal adjacent channel performance at high bit rates, a radio with an accurate carrier frequency and an accurate modulation index is required. For optimum channel utilization, (eg. low BER and high data rates) attention must be made to the phase and frequency response of both the IF and baseband circuitry, and to the accuracy of the Tx/Rx carrier frequencies. Bit Rate, BT and Bandwidth The maximum data rate that can be transmitted over a radio channel depends on the following: Channel spacing Allowable adjacent channel interference Tx filter bandwidth Peak carrier deviation (Modulation Index) Tx and Rx carrier frequency accuracies Modulator and demodulator linearity Receive IF filter frequency and phase characteristics Use of error correction techniques Acceptable error-rate As an example, for MOBITEX operation, a raw data rate of 8kbits/sec at 12.5kHz channel spacing may be achievable - depending on local regulatory requirements, using a ± 2kHz maximum deviation, a BT of 0.3, and no more than 1.5kHz discrepancy between Tx and Rx carrier frequencies. Forward error correction (FEC) could then be used with interleaving to reduce the effect of burst errors. Reducing the data rate to 4800bits/sec would allow the BT to be increased to 0.5, thus improving the error rate performance. For CDPD operation, a 19 200 bits/sec raw data rate at 30kHz channel spacing may be utilised with a ± 8kHz maximum deviation, a BT of 0.5, and no more than 3kHz discrepancy between Tx and Rx carrier frequencies. These examples should be used for guidance purposes only. Regulatory compliance of a design should be verified. FM Modulator, Demodulator and IF For optimum performance, the 'eye' pattern of the received signal (when receiving random data) applied to the FX579 should be as close as possible to the transmit 'eye' pattern examples shown in Figure 5. Of particular importance are general symmetry, cleanliness of the zero crossings, lack of overshoot and, for a BT of 0.3, the relative amplitude of the inner eye opening. To achieve this, attention must be paid to: a) Linearity and frequency/phase response of the Tx frequency modulator. (Unless the transmit data is especially encoded to remove low frequency components, the modulator frequency response should extend down to a few hertz. Hence two point modulation is necessary for synthesised radios.)

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 18 D/579/4 b) Bandwidth and phase response of the Rx IF filters. c) Accuracy of the Tx and Rx carrier frequencies. (Any difference will shift the received signal towards one of the skirts of the IF filter response.) AC Coupling of Tx and Rx Signals Ideally, the transmit path to the modulator should be dc coupled. Similarly, the Rx demodulated signal after external adjustment should be dc coupled to the FX579 RXIN pin, providing a signal symmetrically centred about VBIAS. Figure 9 shows the bit error rate (BER) performance under these conditions for BT values of 0.3 and 0.5 in peak averaging mode. However, practical applications may require ac coupling from the FX579's transmit output to the frequency modulator and between the receiver's frequency discriminator and the FX579's receive input. This creates two problems: a) AC coupling of the signal will degrade the FX579's bit error rate (BER) performance, as shown in Figure 10 for a data rate of 8kbits/sec, with V DD = 5V and BT = 0.3. b) AC coupling at the receive input will transform a step in the voltage at the discriminator output to a slowly decaying pulse which can confuse the FX579's level measuring circuits. Sufficient time should therefore be allowed for the signal into the FX579 to settle before the ACQUIRE line is activated. It is recommended that a data message does not contain long sequences of consecutive ones or zeroes and that the Tx and Rx path frequency responses have cut off frequencies of ≤5Hz and ≤20Hz respectively, for a data rate of 8kbits/sec and BT = 0.3. Two-Point Modulation When designing the FX579 into a radio that uses a frequency synthesiser, a two point modulation technique is recommended. This is to prevent the radio's PLL circuitry from counteracting the modulation process, and so provide a clean flat modulation response down to dc. The transmit output (after the external RC) should be suitably buffered before being applied to the radio's synthesizer. The drive should be applied to both the Voltage Controlled Oscillator and Reference Oscillator Modulation inputs with suitable ac/dc levels and with correct phase to achieve good cancellation of the loop's feedback and so provide a flat modulation response.

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 20 D/579/4

1.7 Performance Specification

1.7.1 Electrical Performance

Exceeding these maximum ratings can result in damage to the device. Min. Max. Units Supply voltage (VDD ) -0.3 7.0 V Voltage on any pin (ref. VSS = 0V) -0.3 VDD + 0.3 V Current into or out of VDD and VSS pins -30 +30 mA Current into or out of any other pin -20 +20 mA Storage Temperature -55 +125 °C Operating Temperature -40 +85 °C Total allowable power dissipation at Tamb=25°C 800 mW Operating Limits Correct operation of the device outside these limits is not implied. Condition Min. Max. Units Operating Temperature -40 +85 °C Supply Voltage (VDD ) 3.0 5.5 V Xtal/Clock Frequency (VDD < 4.5V) 1.0 5.0 MHz Xtal/Clock Frequency (VDD ≥ 4.5V) 1.0 6.5 MHz Data Rate (VDD < 4.5V) 4000 20 000 bits/sec Data Rate (VDD ≥ 4.5V) 4000 40 000 bits/sec Operating Characteristics All device characteristics are measured under the following conditions unless otherwise specified: Tamb = 25°C, VDD = 5.0V, Xtal frequency = 4.096MHz Data rate = 8000 bits/sec, Noise bandwidth = bit rate Characteristic Note Min. Typ. Max. Units Static Values Supply Current (for V DD = 3.0V) 1 - - 2 mA (for VDD = 5.0V) 1 - - 4 mA Logic "1" input level 3.5 - - V Logic "0" input level - - 1.5 V Logic input current 2 -5.0 - 5.0 µA Logic "1" Output Level at IOH = -120µA 4.6 - - V Logic "0" Output Level at IOL = 120µA - - 0.4 V

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 21 D/579/4 Characteristic Note Min. Typ. Max. Units Transmit Parameters TXOP output impedance 3 - 100 - Ω TXOP output level 4, 6, 9 0.8 1.0 1.2 Vpk-pk Tx output offset (wrt VBIAS) - -100 - +100 mV Tx data delay (BT = 0.3) 5 - 2.0 2.5 bit periods Tx data delay (BT = 0.5) 5 - 1.5 2.0 bit periods Receive Parameters RXIN input impedance 3 - M Ω RXIN input level 7, 9 0.7 1.0 1.3 Vpk-pk Rx dc offset from ½ VDD 9 - ±0.5 - V Rx time delay 8 - - 3 bit periods On-Chip Xtal Oscillator Input impedance 10 10 - M Ω Output impedance 10 - 50 - kΩ Voltage gain 10 - 25 - dB "High" clock pulse width 11 60 - - ns "Low" clock pulse width 11 60 - - ns Notes: 1. Not including any current drawn from the modem pins by external circuitry 2. For VIN in the range VSS to VDD 3. Measured by ac coupling an external 1kHz source via suitable resistance to the TXOP pin. The value specified is the average of values measured in the all "1"s and all "0"s states 4. Data pattern of "1111000011110000..." 5. Measured between the rising edge of the Tx DATACLK and the centre of the corresponding bit at the output of the external RC network connected to TXOP 6. Measured at the output of the external RC network 7. For optimum performance, measured at RXIN for a "1111000011110000..." pattern 8. Measured between the centre of bit at RXIN and corresponding rising edge of the Rx data clock 9. Levels are proportional to applied VDD 10. Small signal measurement at 100Hz with no load on XTALN output 11. Timing for an external clock input to the XTAL/CLK pin

Half Duplex GMSK Modem FX579  1996 Consumer Microcircuits Limited 22 D/579/4

1.7.2 Packaging

Figure 11 SOIC Mechanical Outline: Order as part no. FX579D4

Half Duplex GMSK Modem FX579 Handling precautions: This product includes input protection, however, precautions should be taken to prevent device damage from electro-static discharge. CML does not assume any responsibility for the use of any circuitry described. No IPR or circuit patent licences are implied. CML reserves the right at any time without notice to change the said circuitry and this product specification. CML has a policy of testing every product shipped using calibrated test equipment to ensure compliance with this product specification. Specific testing of all circuit parameters is not necessarily performed. CONSUMER MICROCIRCUITS LIMITED1 WHEATON ROAD Telephone: +44 1376 513833 WITHAM - ESSEX CM8 3TD - ENGLAND Telefax: +44 1376 518247