FCBG110SD1C01B-C ATGBICS

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 6

Technical content

ATGBICS® All rights reserved. EOE Ref: ATGBICS_ FCBG110SD1C01B-C_V1 Page 1 of 6 Product Datasheet FCBG110SD1C01B-C Finisar® Compatible 1G/10Gb/s SFP+ Active Optical Cable, Active, 1m

FEATURES

  • Hot pluggable
  • Bit rate support from 1G to 11.3Gbps
  • Up to 100m by active optical cable with OM2/OM3 fiber
  • Pre-terminated fiber cable
  • Operating environment temperature 0 ~ 70℃
  • Low power consumption
  • SFP+ housing with enhanced EMI shielding
  • Single 3.3V power supply
  • Programmable EEPROM for serial identification

APPLICATIONS

  • 10G Ethernet
  • Applicable to 1G Ethernet
  • 8G Fiber Channel
  • Applicable to 4G / 2G / 1G Fiber Channel
  • 10G Fiber Channel over Ethernet
  • 1X QDR Infiniband
  • Applicable to 1X DDR / 1x SDR Infiniband
  • High-capacity IO with SFP+ interface
  • Data center and in-rack connection
  • Compliance
  • SFF-8431 SFP+ Electrical MSA
  • SFF-8432 SFP+ Mechanical MSA
  • RoHS complaint

DESCRIPTION

ATGBICS SFP AOC cable assemblies are high-performance, cost effective I/O solutions for 10Gb Ethernet and 10G Fiber Channel applications. SFP+ active optical cables allow hardware manufacturers to achieve high port density, configurability, and utilization at a very low cost and to reduce power budget. The high- speed cable assemblies meet and exceed the performance and reliability requirements stipulated by Gigabit Ethernet and Fiber Channel industry standard.

ATGBICS® All rights reserved. EOE Ref: ATGBICS_ FCBG110SD1C01B-C_V1 Page 2 of 6 Product Datasheet Host Board Connector Pin (Top View) Note: 1. For detail information, please refer to SFF-8083 0.8mm Card Edge Connector for 8/10 Gbps

ATGBICS® All rights reserved. EOE Ref: ATGBICS_ FCBG110SD1C01B-C_V1 Page 3 of 6 Product Datasheet SFP+ Connector Pin Pin Symbol Logic Description Note

1 VeeT Module Transmitter Ground 1

2 Tx_Fault LVTTL-O Not supported. 3 3 Tx_Disable LVTTL-I Not supported. 3

4 SDA LVTTL-I/O 2-wire Serial Interface Data Line 2

5 SCL LVTTL-I/O 2-wire Serial Interface Clock 2

6 Mod_ABS Module Absent 2

7 RS0 LVTTL-I Not supported. 3 8 Rx_LOS LVTTL-O Not supported. 3 9 RS1 LVTTL-I Not supported. 3

10 VeeR Module Receiver Ground 1

11 VeeR Module Receiver Ground 1

12 RD- CML-O Receiver Inverted Data Output

13 RD+ CML-O Receiver Non-Inverted Data Output

14 VeeR Module Receiver Ground 1

15 VccR Module Receiver 3.3 V Supply 4 16 VccT Module Transmitter 3.3 V Supply 4

17 VeeT Module Transmitter Ground 1

18 TD+ CML-I Transmitter Non-Inverted Data Input

19 TD- CML-I Transmitter Inverted Data Input

20 VeeT Module Transmitter Ground 1

ATGBICS® All rights reserved. EOE Ref: ATGBICS_ FCBG110SD1C01B-C_V1 Page 4 of 6 Product Datasheet Notes: 1. Module circuit ground pins are isolated from the module chassis ground 2. Pull up to VccHost with 4.7k – 10k 3. No connection required 4. Power supply filtering circuit required Absolute Maximum Ratings Parameter Symbol Min Max Unit Storage Temperature Ts -40 +85 °C Operating Case Temperature Tc -40 +85 °C Operating Humidity RH 85 % Supply Voltage Vcc -0.5 3.6 V Note: Damage may occur if the transceiver is subjected to conditions beyond the limits. Recommended Operating Conditions Parameter Symbol Min Max Unit Operating Case Temperature Tc 0 +70 °C Supply Voltage Vcc 3.1 3.5 V Bit Rate BR 1 11.3 GB

ATGBICS® All rights reserved. EOE Ref: ATGBICS_ FCBG110SD1C01B-C_V1 Page 5 of 6 Product Datasheet Host PCB Layout

ATGBICS® All rights reserved. EOE Ref: ATGBICS_ FCBG110SD1C01B-C_V1 Page 6 of 6 Product Datasheet Recommended Power Supply Filter References: 1. SFF-8431 “Specifications for Enhanced Small Form Factor Pluggable Module SFP+” 2. SFF-8432 “Specification for Improved Pluggable Form factor” 3. SFF-8472 “Specification for Diagnostic Monitoring Interface for Optical Transceivers” Mechanical Drawing