ECB01913 E-CMOS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 8
Technical content
Features
Internally embedded 1A Max. charge mode, charging current adjustable when under 1A； OVP function when charge , charge terminated when charge voltage over 6.2V； Trickling/CC/CV three charging stages , fully charges voltage of 4.22V adjustable 0 V Battery chargeable Thermo charging protection function, charging current starts to decline from 120 degree Celsius, could lower down to zero output. Fixed switching frequency @ 650KHZ in discharge, Power MOSFET driven externally and moderately to reach flexible application Internal 0.6V reference Voltage, adjustable output voltage; Internal 0.68V OVP threshold output current adjustable Meet dual start up modes of button and triggered by EN pin Constant Output Power function with OCP (Over Current) and SCP (Short Circuit Protection) Boost function allowed during charge period, indicating LED remains charging status and capacity boost starts when loading being sense, fall into sleeping mode when loading removed or under 50mA 4 indicating LED controlled to show capacity precisely Can be defined as a Li- ion battery charger specifically Direct drive Flashlight LED with max. 50mA without external resistors required Battery over- charge and over- discharge protection Internal Function Block
QC 2.0 compliant Portable Power Bank Single Chip IC Typical Application A：Single Port Single Chip application Typical Application B: Single Port W/ QC application
QC 2.0 compliant Portable Power Bank Single Chip IC Typical Application A: Dual Ports w/ QC application
QC 2.0 compliant Portable Power Bank Single Chip IC Pin Configuration
Ordering Information
Symbol Pin # Description STB 1 Stand- by Control L4 2 LED Indicator # 4 L3 3 LED Indicator # 3 L2 4 LED Indicator # 2 L1 5 LED Indicator # 1 VDD 6 VDD 5V in KEY 7 To Button EN 8 Boost Enable CE 9 Loading Sensing LED/Aux 10 Flash LED/ Auxiliary BTP 11 To Battery + FB 12 Output basis of boost PROG 13 Charging current programming Pin GND 14 Ground CS 15 Inductor peak current sensing Pin when Boost GATE 16 Ext. Gate driving Pin when Boost Part No. Package type Marking Remark ECB01913M1R SOP-16L ECB01913 LLLLL YYWW 1. LLLLL：The last five numbers of LOT. 2. YY：Year code；Year 2014=14 3. WW：Week code；01~52 ECB01913 XX X R : Tape Reel M1：SOP-16L VDD KEY CE GATE GND BTP LED/Aux CS FB STB1 PROG EN
QC 2.0 compliant Portable Power Bank Single Chip IC DC Parameter （Unless specified, all parameters measured under room Temp. and set GND potential as 0 potential ） Symbol Characteristics Test Condition Unit Min Typ Max Systematic Parameter VIN Input Voltage Range V 4.5 5 5.5 Vbat Battery Voltage V 2.8 4.35 Isleep Sleep Mode Current BTP=3.2- 4.2V uA 50 Charge Parameter VIN Drop out Monitor VIN (Low to High) VIN>BAT mV 100 VIN( High to Low) VIN>BAT mV 30 Vfloat Floating Gate voltage V 4.18 4.22 4.26 Ibat BAT reverse current uA ±0.5 ±5 VTRKL Trickling turns to CCM Volt VBAT low to high V 2.8 VTRHYS Trickling charge hysteresis Volt. mV 100 VUV Vcc under voltage lock- out Vcc low to high V 3.7 VUVHYS Vcc under voltage lock- out hysteresis mV 200 VRECHG Recharge Voltage threshold V 4.1 Vprog1 PROG Volt. when Trickling V 0.1 Vprog2 PROG Volt. when large Current V 1 FLED LED Flicker Freq. when Charge Hz 1 VOVPC OVP when Charge V 6.0 6.2 6.4 Symbol Characteristics Test Condition Unit Min Typ Max Discharge Parameter VEN Enable On Volt. V 0 1.5 FB Ref. Volt. of Boost system mV 582 600 618 INOLOADOFF Zero load detect current threshold mA 25 50 75 TNOLOADOFF Off Delay time for boost when zero load S 12 16 20 Fsw Switching Freq. KHZ 520 650 780 Dmax Max. duty Cycle % 78 90 95 TN_DRIVE N GATE driving time (load=1nF) Rise Time nS 10 Fall Time nS 8.5 Vocp Peak Current threshold Volt. BTP=3.6V mV 115 120 125 Constant Power Output current bias BTP=3.2-4.2V % -10 0 10 Tss Soft star time mS 2 OVP OVP starts threshold Volt. mV 660 680 700 OVP_HYS OVP threshold Hysteresis Volt mV 615 635 654 Td_OVP OVP turn off delay uS 30 VSD1 Boost shut down Voltage when low power capacity VBAT high to low V 2.8 VUVLO_R UVLO Recovery Volt. VBATlow to high V 3.00 Iauto_off Loading current of Auto- off BAT=2.8-4.2V L=2.2uH mA 25 50 75 OTP Over Temp. Protection degC 150 OTP_HYS OTP Hysteresis degC 30
QC 2.0 compliant Portable Power Bank Single Chip IC Function and Characteristics Charge Management Portion （1）Fully charged Volt. set @ typical 4.22V （2）Max. charging current can reach 1A; When under 1A required, thru Rch resistor on PROG Pin to GND While Ich=1200/(Rch+1200)(A) （3）Pre- charge function when VBAT under 2.8V(Current= Ich*10%） （4）0V Battery chargeable （5）Three stage charge function: Tickling / Constant Current/ Constant Voltage （6）Thermo Charging protection, charge current starts to decline from 120℃, and down to 0 when 150℃ Boost( Discharge Management Portion) （1）Switching Freq. @ 650KHZ to drive external N- MOS and adjust output voltage and current （2）After loading current < 50mA being sensed for 16 Seconds,ECB01913 would turn into Stand- by mode （3）Automatic loading detect function，user could wake up system with button or EN Pin when design （4）Constant Power design，OCP point lower down along with battery voltage. When output current surpasses OCP point, output voltage declines to maintain stable output power until output voltage turns to be as low as battery voltage, which system would judge as over current or short- circuit state to shut down （5）Boost reference voltage@ 0.6V, with suitable dividing resistors to alter output voltage, equation is- Vout=0.6×(1+R3/R4)，With OVP function，when output voltage surpasses Vovp= 0.68×(1+R3/R4), boost function would be interrupted；Also, the peak boost voltage must under 9V （6）3.2V Indicator LED1starts to flicker when Vbat < 3.2V; A. When boost not being triggered and Vbat < 3.0V, button won't effect, and LED1 would flicker for 8 seconds.； B. When boost not being triggered and Vbat > 3.0V, Boost function can be waken with button until Vbat falls under 2.8V, discharge output would be turned off, at this moment, LED1 still flickers for 8 seconds. （7）Max. output current can be decided by R2, when Vbat is 3.6V, output current can be calculated by： Iout =0 .04/R2， When Vbat is higher or lower than 3.6V, output current tolerance is < 15% In normal case of application, user can set R2= 0.04 Ohm to gain 1A output current , and By setting R2= 0.02 Ohm to gain 2A output current （8）Boost/ Discharge allowed while internal battery being charged, and LEDs indication follows rules of charging state shown below in “Charge/ Discharge Indicating LED Intro.” Charge/ Discharge Indicating LED Intro. （1） Charge/ Discharge indicating LEDs Marquee is shown in below chart （2） When discharging, if Vbat falls under2.8V, system would be shut down； when Vbat raises from low to high and before reaching 3.0V, boost action would not be ignited by inserting any loads or clicking button, and LED1 would flicker for 8 seconds to remind low battery voltage （3）In sleeping mode, by clicking button to check status, LEDs would flicker for 8 seconds in accordance With actual battery condition in the following methods—
QC 2.0 compliant Portable Power Bank Single Chip IC Operating Mode * Internal Battery Status L1 L2 L3 L4 (Boost)Discharge BAT<3.2V Flicker off off off 3.2≤BAT<3.45V on off off off 3.45≤BAT<3.65V on on off off 3.65≤BAT<3.80V on on on off 3.80≤BAT on on on on Charge 3.65≤BAT Surge Surge Surge Surge 3.65≤BAT<3.80V on Surge Surge Surge 3.80≤BAT<4.00V on on Surge Surge 4.00≤BAT<4.22V on on on Surge 4.22=BAT on on on on Stand- by - off off off off * Flicker Frequency of LED during Discharge period is 2 HZ, with duty cycle of 50% * Surge of 4 LEDs during Charge period is exposed of 1 HZ, with 250mS on- state each Specified in Li-ion Battery charging and Power Capacity Indication 1. When connect LED/ Aux pin with BAT, ECB01913 turns into single LED indicating mode, which is only applied to charge Li- ion battery and under voltage indication. Single LED flickers when charging, and is ON state when battery fully charged. User can either choose EN Pin or KEY Pin to ignite Boost function, but other LEDs won't show boost status 2. In this mode, when any of protection modes occur, user is demanded to reset manually for safety concerns. Flashlight Control （1）Double click button can turn on Flash; Turning off by another action of double click （2）No external resistors required to control white light LED with max. output of 50mA EN PIN control function （1）Boost function being triggered when EN in low level； （2）Boost function stops when EN set floating or being pulled high level （3）Min loading current sensing function being stopped in this phase, and Boost action remains
QC 2.0 compliant Portable Power Bank Single Chip IC