8135435 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 8
Technical content
ORIGINAL INSTRUCTIONS GC 0624 WELDING EARTH CLAMPS MODEL NO: EC200, EC300 & EC500 PART NO: 8135435, 8135440 & 8135445
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE product. Please follow the instructions given. In doing so you will ensure the safety of yourself and that of others around you and you can look forward to the product giving you long and satisfactory service. .Always read the safety warnings before use. Tested in accordance with BS EN 60974-13:2021. WARNING: ELECTRIC SHOCK CAN KILL. DO NOT TOUCH LIVE ELECTRICAL PARTS WITH BARE HANDS AND DO NOT USE WET OR DAMP GLOVES OR CLOTHING. USE THIS CLAMP ONLY FOR ELECTRICAL WELDS AND FOR RETURN CURRENT OF THE WELDING CIRCUIT. For electrical conductivity make sure that the welding cable is properly connected to the clamp. The end of the cable must be properly sheathed and secured by tightening the special pins or the bolt of the cable clamp plate. Use the cable section indicated above. Make sure that the clamp is properly connected to the workpiece to be welded, cleaning the contact area adequately. Welding gloves must be worn when using this clamp. DO NOT use at a higher amperage than the approved amperage rating. DO NOT use this clamp for purposes other than those specified. If it is damaged, the clamp must be replaced. Cleaning and repair of the welding machine MUST BE CARRIED OUT with the machine SWITCHED OFF and disconnected from the electrical supply. Model No EC200 EC300 EC500 Part No 8135435 8135440 81354345 Amperage at 30% Duty 500A Amperage at 40% Duty 300A Amperage at 60% Duty 200A Cable Section 25-35mm 2 25-50mm 2 35-70mm2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com The following safety symbols are to be found on this product. Danger of electric shock Spark hazard - wear eye protection Heat hazard - wear protective gloves Read the user manual GENERAL SAFETY WARNINGS 1. When welding indoors, ensure there is adequate ventilation. 2. NEVER look at an electric arc without protection. A welding headshield or helmet with appropriate lenses must be used when welding. All persons present must always use a proper welding face shield with suitable lenses. 3. After welding, ALWA YS check that the area is free of any sparks or glowing embers. 4. When necessary, use identical replacem ent parts to ensure that the safety of the product is maintained. ENVIRONMENTAL PROTECTION DO NOT dispose of welding products with general household waste. They contain valuable raw materials and should be disposed of appropriately at a recognised disposal facility. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for its intended purpose. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ACCESSORIES FROM THE CLARKE CATALOGUE
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - EC200
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - EC300
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - EC500