E5270B

E5270B KEYSIGHT | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 20

Technical content

Precision IV Analyzer/8 Slot Precision Measurement Mainframe Data Sheet

Keysight Technologies, Inc. E5270B Precision IV Analyzer is the complete solution for current-voltage characterization of a wide range of materials and devices. The E5270B supports multiple SMUs (Source/Monitor Units) for voltage/current sourcing and voltage/current measurement with the best in the class current measurement performance as low as 0.1 fA. Its modular architecture allows you to configure or upgrade SMU modules for available eight slots. The EasyEXPERT group+ GUI based characterization software is furnished and available on your PC to support all the tasks required in the characterization from the measurement setup to the data analysis. Powerful integration of SMU’s versatile measurement capabilities and GUI based characterization software makes the E5270B the best solution for characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reli - ability and efficiency. Keysight EasyEXPERT group+ supports efficient and repeatable device characterization in the entire characterization process from measurement setup and execution to analysis and data management either by interactive manual operation or automation across a wafer in conjunction with a semiauto - matic wafer prober. EasyEXPERT group+ makes it easy to perform current-voltage characterization immediately with the ready-to-use measurements (application tests) furnished, and allows you the option of storing test condition and measurement data automatically after each measurement in a unique built-in database (workspace), ensuring that valuable information is not lost and that measurements can be repeated at a later date. Keysight E5270B provides the complete solution for current-voltage characterization with these versatile capabilities. In addition to using as an analyzer, the E5270B is available as a system component SMU for a rack and stuck test system. It provides the scalability and the highest measurement accuracy in the class for current-voltage measurement. It can be controlled remotely by the FLEX command set supporting the powerful measurement capabilities.

03 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet Basic features Current-voltage measurement capabilities – Accurate and precision measurement ranges of 0.1 fA – 1A and 0.5 µV – 200 V – Spot and sweep measurement capabilities – Pulse spot and sweep measurement with minimum 500 µs pulse width – The ASU (atto-sense and switch unit) can be used with the HRSMU to provide 0.1 fA measurement resolution and SMU/AUX path switching EasyEXPERT group+ software – Characterization environment is available on user’s PC – Intuitive GUI based operation with keyboard and mouse operation – Application Test mode provides the furnished ready-to-use application tests for quick measurement execution (Available application tests can be adapted to configured resources.) – Classic test mode provides easy access to the instrument features – Graphical display and analysis capabilities facilitate front-end data analysis without additional utilities and support report generation as image data or Excel data. – Individualized built-in database (workspace) records test data automatically and simplifies the data management without annoying numerous data files. – Quick test mode supports test sequencing without programming – GUI-based control of the Keysight B2200A, B2201A and E5250A switching matrices – EasyEXPERT remote control function supports the remote execution of application tests via the LAN interface – Data back capability and various data protection feature for shared usage by multiple users – EasyEXPERT group+ can be installed on as many PCs as you need without additional charge to take advantage of offline personal analyzer environment among users in your department. E5270B hardware – Configurable and upgradable measurement modules up to 8 slots – High Resolution SMU (HRSMU), Medium Power SMU (MPSMU) and High Power SMU (HPSMU) are available for configurable SMU selection. Optional ASU is supported for HRSMU. – High-resolution and high-speed analog-to-digital converters (ADCs) are available to all installed modules – Active ground unit (GNDU) in mainframe to force 0 V and sink the current up to 4 A – Multiple interfaces (GPIB, trigger in/out and digital I/O) – FLEX command set and program memory for remote control programming – Self-test, self-calibration and diagnostics functions

The measurement and output accuracy are specified at the module connector terminals when referenced to the Zero Check terminal under the following conditions: – Temperature: 23°C ± 5°C (double for 5°C to 18°C, and 28°C to 40°C if not noted otherwise) – Humidity: 15 % to 60 % (double for 60 % to 70 %) – After 40 minutes warm-up E5270B Mainframe Specification Supported plug-In modules The E5270B supports eight slots for plug-in modules. – Ambient temperature change less than ± 1°C after auto calibration execution – Measurement made within one hour after auto calibration execution – Averaging (high-speed per-SMU ADC): 128 samples in 1 PLC; Integration time (high-resolution central ADC):

1 PLC (1 nA to 1A range)

20 PLC (100 pA range)

50 PLC (1 pA to 10 pA range)

– Filter: ON (for SMUs) – Kelvin connection – Calibration period: 1 year Maximum output power The total module power consumption cannot exceed 80 W. Note: Using the HPSMU, MPSMU, and Atto Level HRSMU units, it is impossible to create a combination that exceeds the 80 watt limit. Maximum voltage between common and ground ≤ ± 42 V Pulse measurement Pulse width: 500 µsec to 2 s Pulse period: 5 ms to 5 s Period ≥ width + 2 ms (when width ≤ 100 ms) Period ≥ width + 10 ms (when width > 100 ms) Pulse resolution: 100 µs Ground unit (GNDU) specification The GNDU is furnished with the E5270B mainframe. Output voltage: 0 V ± 100 µV Maximum sink current: 4 A Output terminal/connection: Triaxial connector, Kelvin (remote sensing) GNDU supplemental information Load capacitance: 1 µF Cable resistance: For IS ≤ 1.6 A: Force line R < 1 Ω For 1.6 A < I S ≤ 2.0 A: Force line R < 0.7 Ω For 2.0 A < I S ≤ 4.0 A: Force line R < 0.35 Ω For all cases: Sense line R ≤ 10 Ω Where I S is the current being sunk by the GNDU. Note: This document lists specifica - tions and supplemental information for the E5270B and its associated modules. The specifications are the standards against which the E5270B and its associated modules are tested. When the E5270B or any of its associated modules are shipped from the factory, they meet the specifica - tions. The “supplemental” information and “typical” entries in the following specifications are not warranted, but provide useful information about the functions and performance of the instrument. Part number Description Slots occupied Range of operation Measure resolution E5280B HPSMU 2 -200 V to 200 V, -1 A to 1 A 2 µV, 10 fA E5281B MPSMU 1 -100 V to 100 V, -100 mA to 100 mA 0.5 µV, 10 fA E5287A Atto Level HRSMU 1 -100 V to 100 V, -100 mA to 100 mA 0.5 µV, 1 fA E5288A1 Atto Sense and Switch Unit (ASU) – -100 V to 100 V, -100 mA to 100 mA 0.5 µV, 0.1 fA 1. This is connected with the E5287A Atto Level HRSMU 04 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

MPSMU (Medium Power SMU) Module Specifications Voltage range, resolution, and accuracy (MPSMU) Measure resolution Measure accuracy 1 Voltage range Force resolution High speed ADC High resolution ADC Force accuracy

1 High speed ADC High resolution ADC Maximum

±2 V 100 µV 100 µV 2 µV ±(0.03 % + 900 µV) ±(0.03 % + 700 µV) ±(0.02 % + 700 µV) 100 mA ±5 V 250 µV 250 µV 5 µV ±(0.03 % + 2 mV) ±(0.03 % + 2 mV) ±(0.02 % + 1 mV) 100 mA ±20 V 1 mV 1 mV 20 µV ±(0.03 % + 4 mV) ±(0.03 % + 4 mV) ±(0.02 % + 2 mV) 100 mA ±100 V 5 mV 5 mV 100 µV ±(0.04 % + 15 mV) ±(0.03 % + 20 mV) ±(0.03 % + 5 mV) 3 1. ± (% of output/measured value + offset voltage V) 2. 100 mA (Vo ≤ 20 V), 50 mA (20 V < Vo ≤ 40 V), Vo is the output voltage in volts. 3. 100 mA (Vo ≤ 20 V), 50 mA (20 V < Vo ≤ 40 V), 20 mA (40 V < Vo ≤ 100 V), Vo is the output voltage in volts. Current range, resolution, and accuracy (MPSMU) Measure resolution 4 Current range Force resolution High speed ADC High resolution ADC Force accuracy

1 Measure accuracy 1,2 Maximum

±1 nA 50 fA 50 fA 10 fA ±(0.5 %+3 pA+2 fA x Vo) ±(0.5 %+3 pA+2 fA x Vo) 100 V ±10 nA 500 fA 500 fA 10 fA ±(0.5 %+7 pA+20 fA x Vo) ±(0.5 %+5 pA+20 fA x Vo) 100 V ±100 nA 5 pA 5 pA 100 fA ±(0.12 %+50 pA+200 fA x Vo) ±(0.1 %+30 pA+200 fA x Vo) 100 V ±1 µA 50 pA 50 pA 1 pA ±(0.12 %+400 pA+2 pA x Vo) ±(0.1 %+200 pA+2 pA x Vo) 100 V ±10 µA 500 pA 500 pA 10 pA ±(0.12 %+5 nA+20 pA x Vo) ±(0.1 %+3 nA+20 pA x Vo) 100 V ±100 µA 5 nA 5 nA 100 pA ±(0.12 %+40 nA+200 pA x Vo) ±(0.1 %+20 nA+200 pA x Vo) 100 V ±1 mA 50 nA 50 nA 1 nA ±(0.12 %+500 nA+2 nA x Vo) ±(0.1 %+300 nA+2 nA x Vo) 100 V ±10 mA 500 nA 500 nA 10 nA ±(0.12 %+4 µA+20 nA x Vo) ±(0.1 %+2 µA+20 nA x Vo) 100 V ±100 mA 5 µA 5 µA 100 nA ±(0.12 %+50 µA+200 nA x Vo) ±(0.1 %+30 µA+200 nA x Vo) 4. ± (% of output/measured value + offset current A (fixed part determined by the output/measurement range + proportional part that is multiplied by Vo) 5. Measurement accuracy when using either the high-speed ADC or the high-resolution ADC 6. 100 V (Io ≤ 20 mA), 40 V (20 mA < Io ≤ 50 mA), 20 V (50 mA < Io ≤ 100 mA), Io is the output current in amps. 7. Specified measurement resolution is limited by fundamental noise limits. MPSMU measurement and output range Power consumption (MPSMU) Voltage source mode: Voltage range Power

0.5 V 20 x Ic (W)

2 V 20 x Ic (W)

5 V 20 x Ic (W)

20 V 20 x Ic (W)

40 V 40 x Ic (W)

100 V 100 x Ic (W)

Where Ic is the current compliance setting. Current source mode: Voltage compliance Power Vc ≤ 20 20 x Io (W) 20 < Vc ≤ 40 40 x Io (W) 40 < Vc ≤ 100 100 x Io (W) Where Vc is the voltage compliance setting and Io is output current. 100 -20 -50 -100 -100 -40 -20 20 40 100 Current (mA) Voltage (V) 05 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

Output terminal/connection: Triaxial connector, Kelvin (remote sensing) Voltage/current compliance (limiting) The SMU can limit output voltage or current to prevent damaging the device under test. Voltage: 0 V to ±100 V Current: ±1 pA to ±100 mA Compliance accuracy: Same as the current (or voltage) set accuracy. MPSMU supplemental information Maximum allowable cable resistance (Kelvin connection): Force line: 10 Ω Sense line: 10 Ω Voltage source output resistance: 0.3 Ω typical (Force line, non-Kelvin connection) Voltage measurement input resistance: ≥ 10 13 Ω Current source output resistance: ≥ 1013 Ω (1 nA range) Current compliance setting accuracy (for opposite polarity): For 1 nA to 10 nA ranges: I setting accuracy ± 12 % of range For 100 nA to 100 mA ranges: I setting accuracy ± 2.5 % of range Maximum capacitive load: For 1 nA to 10 nA ranges: 1000 pF For 100 nA to 10 mA ranges: 10 nF For 100 mA ranges: 100 µF Maximum guard capacitance: 900 pF Maximum shield capacitance: 5000 pF Maximum guard offset voltage: ± 3 mV Noise characteristics (typical, filter ON): Voltage source: 0.01 % of V range (rms) Current source: 0.1 % of I range (rms) Overshoot (typical, filter ON): Voltage source: 0.03 % of V range Current source: 1 % of I range Range switching transient noise (typical, filter ON): Voltage ranging: 250 mV Current ranging: 10 mV Slew rate: 0.2 V/µs SMU pulse setting accuracy (fixed measurement range): Width: 0.5 % + 50 µs Period: 0.5 % + 100 µs Trigger out delay (pulsed measurements): HPSMU (High Power SMU) Module Specifications Voltage range, resolution, and accuracy (HPSMU) Measure resolution Measure accuracy 1 Voltage range Force resolution High speed ADC High resolution ADC Force accuracy

1 High speed ADC High resolution

±2 V 100 µV 100 µV 2 µV ±(0.03 % + 900 µV) ±(0.03 % + 700 µV) ±(0.02 % + 700 µV) 1 A ±20 V 1 mV 1 mV 20 µV ±(0.03 % + 4 mV) ±(0.03 % + 4 mV) ±(0.02 % + 2 mV) 1 A ±100 V 5 mV 5 mV 100 µV ±(0.04 % + 15 mV) ±(0.03 % + 20 mV) ±(0.03 % + 5 mV) 3 ±200 V 10 mV 10 mV 200 µV ±(0.045 % + 30 mV) ±(0.035 % + 40 mV) ±(0.035 % + 10 mV) 4 1. ± (% of output/measured value + offset voltage V) 2. 1 A (Vo ≤20 V), 500 mA (20 V <Vo ≤40 V), Vo is the output voltage in volts. 3. 1 A (Vo ≤20 V), 500 mA (20 V <Vo ≤40 V), 125 mA (40 V <Vo ≤100 V), Vo is the output voltage in volts. 4. 1 A (Vo ≤20 V), 500 mA (20 V <Vo ≤40 V), 125 mA (40 V <Vo ≤100 V), 50 mA (100 V <Vo ≤200 V), Vo is the output voltage in volts. Current range, resolution, and accuracy (HPSMU) Measure resolution 5 Current range Force resolution High speed ADC High resolution ADC Force accuracy ±1 nA 50 fA 50 fA 10 fA ±(0.5 %+3 pA+2 fA x Vo) ±(0.5 %+3 pA+2 fA x Vo) 200 V ±10 nA 500 fA 500 fA 10 fA ±(0.5 %+7 pA+20 fA x Vo) ±(0.5 %+5 pA+20 fA x Vo) 200 V ±100 nA 5 pA 5 pA 100 fA ±(0.12 %+50 pA+200 fA x Vo) ±(0.1 %+30 pA+200 fA x Vo) 200 V ±1 µA 50 pA 50 pA 1 pA ±(0.12 %+400 pA+2 pA x Vo) ±(0.1 %+200 pA+2 pA x Vo) 200 V ±10 µA 500 pA 500 pA 10 pA ±(0.12 %+5 nA+20 pA x Vo) ±(0.1 %+3 nA+20 pA x Vo) 200 V ±100 µA 5 nA 5 nA 100 pA ±(0.12 %+40 nA+200 pA x Vo) ±(0.1 %+20 nA+200 pA x Vo) 200 V ±1 mA 50 nA 50 nA 1 nA ±(0.12 %+500 nA+2 nA x Vo) ±(0.1 %+300 nA+2 nA x Vo) 200 V ±10 mA 500 nA 500 nA 10 nA ±(0.12 %+4 µA+20 nA x Vo) ±(0.1 %+2 µA+20 nA x Vo) 200 V ±100 mA 5 µA 5 µA 100 nA ±(0.12 %+50 µA+200 nA x Vo) ±(0.1 %+30 µA+200 nA x Vo) ±1 A 50 µA 50 µA 1 µA ±(0.5 %+500 µA+2 µA x Vo) ±(0.5 %+300 µA+2 µA x Vo) 4 5. (% of output/measured value + offset current A (fixed part determined by the output/measurement range + proportional part that is multiplied by Vo) resolution (< pulse width) 6. Measurement accuracy when using either the high-speed ADC or the high-resolution ADC 7. 200 V (Io ≤ 50 mA), 100 V (50 mA < Io ≤ 100 mA) 8. 200 V (Io ≤ 50 mA), 100 V (50 mA < Io ≤ 125 mA), 40 V (125 mA < Io ≤ 500 mA), 20 V (500 mA < Io ≤ 1 A), Io is the output current in amps. 9. Specified measurement resolution is limited by fundamental noise limits 06 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

Output terminal/connection: Triaxial connector, Kelvin (remote sensing) Voltage/current compliance(limiting) The SMU can limit output voltage or current to prevent damaging the device under test. Voltage: 0 V to ± 200 V Current: ± 1 pA to ± 1 A Compliance accuracy: Same as the current (or voltage) set accuracy. HPSMU supplemental information Maximum allowable cable resistance (Kelvin connection): Force line: 10 Ω (I ≤ 100 mA) Force line: 1.5 Ω (100 mA < I ≤ 1 A) Sense line: 10 Ω (All cases) Voltage source output resistance: 0.2 Ω typical (Force line, non-Kelvin connection) Voltage measurement input Power consumption (HPSMU) Voltage source mode: Voltage range Power

200 V 200 x Ic (W)

Where Ic is the current compliance setting. Current source mode: Voltage compliance Power Vc ≤ 20 20 x Io (W) 20 < Vc ≤ 40 40 x Io (W) 40 < Vc ≤ 100 100 x Io (W) 100 < Vc ≤ 200 200 x Io (W) Where Vc is the voltage compliance setting and Io is output current. HPSMU measurement and output range resistance: ≥ 1013 Ω Current source output resistance: ≥ 1013 Ω (1 nA range) Current compliance setting accuracy (for opposite polarity): For 1 nA to 10 nA ranges: I setting accuracy ± 12 % of range For 100 nA to 1 A ranges: I setting accuracy ± 2.5 % of range Maximum capacitive load: For 1 nA to 10 nA ranges: 1000 pF For 100 nA to 10 mA ranges: 10 nF For 100 mA to 1 A ranges: 100 µF Maximum guard capacitance: 900 pF Maximum shield capacitance: 5000 pF Maximum guard offset voltage: ± 1 mV Noise characteristics (typical, filter ON): Voltage source: 0.01 % of V range (rms) Current source: 0.1 % of I range (rms) Overshoot (typical, filter ON): Voltage source: 0.03 % of V range Current source: 1 % of I range Range switching transient noise (typical, filter ON): Voltage ranging: 250 mV Current ranging: 10 mV Slew rate: 0.2 V/µs SMU pulse setting accuracy (fixed measurement range): Width: 0.5 % + 50 µs Period: 0.5 % + 100 µs Trigger out delay (pulsed measurements): 0 to 32.7 ms with 100 µs resolution (< pulse width) 07 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet 1000 500 125 -50 -125 -500 -1000 -200 -100 -40 -20 20 40 100 200 Current (mA) Voltage (V)

Atto Level HRSMU Module Specifications (without ASU) Voltage range, resolution, and accuracy (Atto level HRSMU without ASU) Measure resolution Measure accuracy 1 Voltage range Force resolution High speed ADC High resolution ADC Force accuracy ±2 V 100 µV 100 µV 2 µV ±(0.02 % + 400 µV) ±(0.01 % + 700 µV) ±(0.01 % + 200 µV) 100 mA ±5 V 250 µV 250 µV 5 µV ±(0.02 % + 750 µV) ±(0.01 % + 2 mV) ±(0.01 % + 250 µV) 100 mA ±20 V 1 mV 1 mV 20 µV ±(0.02 % + 3 mV) ±(0.01 % + 4 mV) ±(0.01 % + 1 mV) 100 mA ±100 V 5 mV 5 mV 100 µV ±(0.03 % + 15 mV) ±(0.02% + 20 mV) ±(0.02 % + 5 mV) 3 1. ± (% of output/measured value + offset voltage) 2. 100 mA (Vo ≤ 20 V), 50 mA (20 V <Vo ≤ 40 V), Vo is the output voltage in volts. 3. 100 mA (Vo ≤ 20 V), 50 mA (20 V <Vo ≤ 40 V), 20 mA (40 V <Vo ≤ 100 V), Vo is the output voltage in volts. Current range, resolution, and accuracy (Atto level HRSMU without ASU) Measure resolution 4,5 Current range Force resolution High speed ADC High resolution ADC Force accuracy ±10 pA 5 fA 1 fA 1 fA ±(0.5 %+40 fA+10 aA x Vo) ±(0.5 %+15 fA+10 aA x Vo) 100 V ±100 pA 5 fA 5 fA 2 fA ±(0.5 %+120 fA+100 aA x Vo) ±(0.5 %+40 fA+100 aA x Vo) 100 V ±1 nA 50 fA 50 fA 10 fA ±(0.25 %+400 fA+1 fA x Vo) ±(0.25 %+300 fA+1 fA x Vo) 100 V ±10 nA 500 fA 500 fA 10 fA ±(0.25 %+4 pA+10 fA x Vo) ±(0.25 %+2 pA+10 fA x Vo) 100 V ±100 nA 5 pA 5 pA 100 fA ±(0.12 %+40 pA+100 fA x Vo) ±(0.1 %+20 pA+100 fA x Vo) 100 V ±1 µA 50 pA 50 pA 1 pA ±(0.12 %+400 pA+1 pA x Vo) ±(0.1 %+200 pA+1 pA x Vo) 100 V ±10 µA 500 pA 500 pA 10 pA ±(0.07 %+4 nA+10 pA x Vo) ±(0.05 %+2 nA+10 pA x Vo) 100 V ±100 µA 5 nA 5 nA 100 pA ±(0.07 %+40 nA+100 pA x Vo) ±(0.05 %+20 nA+100 pA x Vo) 100 V ±1 mA 50 nA 50 nA 1 nA ±(0.06 %+400 nA+1 nA x Vo) ±(0.04 %+200 nA+1 nA x Vo) 100 V ±10 mA 500 nA 500 nA 10 nA ±(0.06 %+4 µA+10 nA x Vo) ±(0.04 %+2 µA+10 nA x Vo) 100 V ±100 mA 5 µA 5 µA 100 nA ±(0.12 %+40 µA+100 nA x Vo) ±(0.1 %+20 µA+100 nA x Vo) 4. ± (% of output/measured value + offset current A (fixed part determined by the output/measurement range + proportional part that is multiplied by Vo) 5. Measurement accuracy when using either the high-speed ADC or the high-resolution ADC. 6. 100 V (Io ≤ 20 mA), 40 V (20 mA < Io ≤ 50 mA), 20 V (50 mA < Io ≤ 100 mA), Io is the output current in amps. 7. Minimum 10 aA display resolution at 10 pA range by 6 digits. 8. Specified measurement resolution is limited by fundamental noise limits. Power consumption (Atto level HRSMU without ASU) Voltage source mode: Voltage range Power Where Ic is the current compliance setting. Current source mode: Voltage compliance Power Vc ≤ 20 20 x Io (W) 20 < Vc ≤ 40 40 x Io (W) 40 < Vc ≤ 100 100 x Io (W) Where Vc is the voltage compliance setting and Io is output current. Atto level HRSMU without ASU measurement and output range 100 -20 -50 -100 -100 -40 -20 20 40 100 Current (mA) Voltage (V) 08 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

Output terminal/connection: Triaxial connector, Kelvin (remote sensing) Voltage/current compliance(limiting) The SMU can limit output voltage or current to prevent damaging the device under test. Voltage: 0 V to ± 100 V Current: ± 100 fA to ± 100 mA Compliance accuracy: Same as the current (or voltage) set accuracy. Atto level HRSMU without ASU supplemental information Maximum allowable cable resistance (Kelvin connection): Force line: 10 Ω Sense line: 10 Ω Voltage source output resistance: 0.3 Ω typical (Force line, non-Kelvin connection) Voltage measurement input resistance: ≥ 10 13 Ω Current source output resistance: ≥ 10 13 Ω (1 nA range) Current compliance setting accuracy (for opposite polarity): For 10 pA to 10 nA ranges: I setting accuracy ± 12 % of range For 100 nA to 100 mA ranges: I setting accuracy ± 2.5 % of range Maximum capacitive load: For 10 pA to 10 nA ranges: 1000 pF For 100 nA to 10 mA ranges: 10 nF For 100 mA ranges: 100 µF Maximum guard capacitance: 900 pF Maximum shield capacitance: 5000 pF Maximum guard offset voltage: ± 3 mV Noise characteristics (typical, filter ON): Voltage source: 0.01 % of V range (rms) Current source: 0.1 % of I range (rms) Overshoot (typical, filter ON): Voltage source: 0.03 % of V range Current source: 1 % of I range Range switching transient noise (typical, filter ON): Voltage ranging: 250 mV Current ranging: 10 mV Slew rate: 0.2 V/µs SMU pulse setting accuracy (fixed measurement range): Width: 0.5 % + 50 µs Period: 0.5 % + 100 µs Trigger out delay (pulsed measurements): 0 to 32.7 ms with 100 µs resolution (< pulse width) Atto Level HRSMU Module Specifications (with ASU) Voltage range, resolution, and accuracy (Atto level HRSMU with ASU) Measure resolution Measure accuracy 1 Voltage range Force resolution High speed ADC High resolution ADC Force accuracy ±2 V 100 µV 100 µV 2 µV ±(0.02 % + 400 µV) ±(0.01 % + 700 µV) ±(0.01 % + 200 µV) 100 mA ±5 V 250 µV 250 µV 5 µV ±(0.02 % + 750 µV) ±(0.01 % + 2 mV) ±(0.01 % + 250 µV) 100 mA ±20 V 1 mV 1 mV 20 µV ±(0.02 % + 3 mV) ±(0.01 % + 4 mV) ±(0.01 % + 1 mV) 100 mA ±100 V 5 mV 5 mV 100 µV ±(0.03 % + 15 mV) ±(0.02% + 20 mV) ±(0.02 % + 5 mV) 3 1. ± (% of output/measured value + offset voltage) 2. 100 mA (Vo ≤ 20 V), 50 mA (20 V <Vo ≤ 40 V), Vo is the output voltage in volts. 3. 100 mA (Vo ≤ 20 V), 50 mA (20 V <Vo ≤ 40 V), 20 mA (40 V <Vo ≤ 100 V), Vo is the output voltage in volts. 09 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

Current range, resolution, and accuracy (Atto level HRSMU with ASU) Measure resolution 4,5 Current range Force resolution High speed ADC High resolution ADC Measure accuracy 1,2 Maximum voltage ±1 pA 1 fA 100 aA 100 aA ±(1.8 %+15 fA) ±(1.8 %+12 fA) 100 V ±10 pA 5 fA 1 fA 400 aA ±(0.5 %+40 fA+10 aA x Vo) ±(0.5 %+15 fA+10 aA x Vo) 100 V ±100 pA 5 fA 5 fA 500 aA ±(0.5 %+120 fA+100 aA x Vo) ±(0.5 %+40 fA+100 aA x Vo) 100 V ±1 nA 50 fA 50 fA 10 fA ±(0.25 %+400 fA+1 fA x Vo) ±(0.25 %+300 fA+1 fA x Vo) 100 V ±10 nA 500 fA 500 fA 10 fA ±(0.25 %+4 pA+10 fA x Vo) ±(0.25 %+2 pA+10 fA x Vo) 100 V ±100 nA 5 pA 5 pA 100 fA ±(0.12 %+40 pA+100 fA x Vo) ±(0.1 %+20 pA+100 fA x Vo) 100 V ±1 µA 50 pA 50 pA 1 pA ±(0.12 %+400 pA+1 pA x Vo) ±(0.1 %+200 pA+1 pA x Vo) 100 V ±10 µA 500 pA 500 pA 10 pA ±(0.07 %+4 nA+10 pA x Vo) ±(0.05 %+2 nA+10 pA x Vo) 100 V ±100 µA 5 nA 5 nA 100 pA ±(0.07 %+40 nA+100 pA x Vo) ±(0.05 %+20 nA+100 pA x Vo) 100 V ±1 mA 50 nA 50 nA 1 nA ±(0.06 %+400 nA+1 nA x Vo) ±(0.04 %+200 nA+1 nA x Vo) 100 V ±10 mA 500 nA 500 nA 10 nA ±(0.06 %+4 µA+10 nA x Vo) ±(0.04 %+2 µA+10 nA x Vo) 100 V ±100 mA 5 µA 5 µA 100 nA ±(0.12 %+40 µA+100 nA x Vo) ±(0.1 %+20 µA+100 nA x Vo) 1. ± (% of output/measured value + offset current A (fixed part determined by the output/measurement range + proportional part that is multiplied by Vo) 2. Measurement accuracy when using either the high-speed ADC or the high-resolution ADC. 3. 100 V (Io ≤ 20 mA), 40 V (20 mA < Io ≤ 50 mA), 20 V (50 mA < Io ≤ 100 mA), Io is the output current in amps 4. Minimum 1 aA display resolution at 1 pA range by 6 digits. 5. Specified measurement resolution is limited by fundamental noise limits. 6. Measurements at lower range are affected strongly by vibrations and shocks. Do not place the environment of vibrations and shocks during measurements. Power consumption (Atto level HRSMU with ASU) Voltage source mode: Voltage range Power Where Ic is the current compliance setting. Current source mode: Voltage compliance Power Vc ≤ 20 20 x Io (W) 20 < Vc ≤ 40 40 x Io (W) 40 < Vc ≤ 100 100 x Io (W) Where Vc is the voltage compliance setting and Io is output current. Atto level HRSMU with ASU measurement and output range 100 -20 -50 -100 -100 -40 -20 20 40 100 Current (mA) Voltage (V) 10 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

Output terminal/connection: Triaxial connector, Kelvin (remote sensing) Voltage/current compliance(limiting) The SMU can limit output voltage or current to prevent damaging the device under test. Voltage: 0 V to ± 100 V Current: ± 10 fA to ± 100 mA Compliance accuracy: Same as the current (or voltage) set accuracy. Atto level HRSMU with ASU supplemental information Maximum allowable cable resistance (Kelvin connection): Force line: 10 Ω Sense line: 10 Ω Voltage source output resistance: 0.3 Ω typical (Force line, non-Kelvin connection) Voltage measurement input resistance: ≥ 1013 Ω Current source output resistance: ≥ 1013 Ω (1 nA range) Current compliance setting accuracy (for opposite polarity): For 1 pA to 10 nA ranges: I setting accuracy ± 12 % of range For 100 nA to 100 mA ranges: I setting accuracy ± 2.5 % of range Maximum capacitive load: For 1 pA to 10 nA ranges: 1000 pF For 100 nA to 10 mA ranges: 10 nF For 100 mA ranges: 100 µF Maximum guard capacitance: 660 pF Maximum shield capacitance: 3500 pF Maximum guard offset voltage: ± 4.2 mV (Iout ≤ 100 µA) Noise characteristics (typical, filter ON): Voltage source: 0.01 % of V range (rms) Current source: 0.1 % of I range (rms) Overshoot (typical, filter ON): Voltage source: 0.03 % of V range Current source: 1 % of I range Range switching transient noise (typical, filter ON): Voltage ranging: 250 mV Current ranging: 10 mV Slew rate: 0.2 V/µs Maximum capacitive load: SMU pulse setting accuracy (fixed measurement range): Width: 0.5 % + 50 µs Period: 0.5 % + 100 µs Trigger out delay (pulsed measurements): 0 to 32.7 ms with 100 µs resolution (< pulse width) Atto Sense and Switch Unit (ASU) AUX path specification Maximum voltage

100 V: between AUX input and AUX common

100 V: between AUX input and circuit common

42 V: between AUX common and circuit common

0.5 A: between AUX input and force output

ASU supplemental information Band width (at –3 dB): < 30 MHz (AUX port) 11 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

– Display error messages – Display spot measurement set value – Display spot measurement result Keypad operations – Set GPIB address – Set local/remote mode – Select measurement channel – Set spot measurement set value – Start calibration/diagnostics MPSMU, HPSMU, and Atto Level HRSMU Measurement Mode Details Spot measurement mode Outputs and measures voltage and current. Staircase sweep measurement mode Outputs swept voltage or current, and measures dc voltage or current. One channel can sweep current or voltage while up to eight channels can measure current or voltage. A second channel can be synchronized with the primary sweep channel as an additional voltage or current sweep source. Linear or log sweeps can be performed. Number of steps: 1 – 1,001 Hold time: 0 – 655.35 s, 1 ms resolution Delay time: 0 – 65.5350 s, 100 µs resolution Multi-channel sweep measurement mode Outputs swept voltage or current, and measures dc voltage or current. Up to eight channels can sweep cur- rent or voltage and up to eight chan - nels can measure current or voltage. Linear or log sweeps can be performed. Number of steps: 1– 1,001 Hold time: 0 – 655.35 s, 1 ms resolution Delay time: 0 – 65.5350 s, 100 µs resolution Pulsed spot measurement mode Outputs a voltage or current pulse and measures dc voltage or current. Pulse width: 500 µs to 100 ms, 100 µs resolution Pulse period: 5 ms to 1 s (≥ pulse width + 4 ms), 100 µs resolution Maximum pulse duty: 50 % Pulsed sweep measurement mode Outputs pulsed swept voltage or current, and measures dc voltage or current. A second channel can be programmed to output a staircase sweep voltage or current synchro - nized with the pulsed sweep output. Staircase sweep with pulsed bias measurement mode Outputs swept voltage or current, and measures dc voltage or current. A second channel can be programmed to output a pulsed bias voltage or current. A third channel can be synchronized with the primary sweep channel as an additional voltage or current sweep source. Quasi-pulsed spot measurement mode Outputs quasi-pulsed voltage and measures dc voltage or current. Linear search measurement mode Outputs and measure voltage or current by using linear search method. Binary search measurement mode Outputs and measure voltage or current by using binary search method. Time Stamp The E5270B supports a time stamp function utilizing an internal quartz clock. Resolution: 100 µs Program Memory The E5270B mainframe contains (volatile) memory that can be used to increase test measurement throughput. Program memory allows the storage of program code in the E5270B, eliminating the need to com - municate over the GPIB interface. In addition, input data can be passed to code sequences stored in program memory. Maximum lines of storable code: 40,000 Maximum number of program sequences: 2,000 Output Data Buffer The number of data points that can be stored in the data buffer varies with the choice of the output data format. Minimum number of storable data Points: 34,034 12 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

Trigger in/out synchronization pulses before and after setting and measur- ing dc voltage and current. Arbitrary trigger events can be masked or activated independently. Input An external trigger input signal can be used to do any of the following: – Start a measurement – Start a measurement at each sweep step for a staircase sweep or multi channel sweep measurement – Start the source output at each sweep step for a staircase sweep, pulsed sweep, staircase sweep with pulsed bias, or multi-channel sweep measurement. – Start the pulsed output for a pulsed spot measurement. – Recover from a wait state. – Input level: TTL level, negative or positive edge trigger, or TTL level, negative or positive gate trigger. Output An output trigger signal can be sent when one of the following events occurs: – The end of a measurement is reached. – The end of a measurement at each sweep step for a staircase sweep or multi channel sweep measurement is reached. – Completion of the source output setup at each sweep step for a staircase sweep, pulsed sweep, staircase sweep with pulsed bias, or multi-channel sweep measurement. – Completion of the pulsed output setup for a pulsed spot measurement. – A trigger command is issued. Output level: TTL level, negative or positive edge trigger, or TTL level, negative or posi - tive gate trigger. General Purpose Digital I/O 16 general-purpose digital I/O signals are available via a 25-pin DIN connector. These pins can be used as an alternative to the BNC trigger-in and trigger-out lines to synchronize the E5270B with other instruments. They can also be used as output and input ports for digital signals. The user can selectively assign pins to trigger mode or digital I/O mode. General Specifications Temperature range Operating: +5°C to +40°C Storage: –20°C to +60°C Humidity range Operating: 15 % to 70 % RH, non-condensing Storage: 5 % to 80 % RH, non-condensing Altitude Operating: 0 m to 2,000 m (6,561 ft) Storage: 0 m to 4,600 m (15,092 ft) Power requirement AC voltage: 90 V to 264 V Line frequency: 47 Hz to 63 Hz Maximum volt-amps (VA) E5270B: 600 VA Regulatory compliance EMC: IEC61326-1/EN61326-1 AS/NZS CISPR 11 KC: RRA Notification amending Radio Waves Act Article 58-2 Safety: IEC61010-1/EN61010-1 CAN/CSA-C22.2 No. 61010-1-12, C/US Certification CE, CSA, RCM ,KC Dimensions E5270B: 426 mm W x 235 mm H x 575 mm D Weight E5270B mainframe only: 17 kg E5280A HPSMU: 2.5 kg E5281A MPSMU: 1.4 kg E5287A HRSMU: 1.5 kg E5288A ASU: 0.5 kg Furnished Accessories – USB-GPIB interface (Keysight 82357B) – GNDU to Kelvin adaptor (Keysight N1254A-100) – Triaxial cables for SMU – Triaxial cable for GNDU – Interlock cable – CD-ROMs (EasyEXPERT install media, VXI plug&play driver and TIS library) Furnished Software – EasyEXPERT group+ See the following section for features and prerequisites. – VXI plug&play driver – TIS library Supported OS: Windows 7 Professional (SP1, 32 bit or 64 bit) 13 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet

14 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet Keysight EasyEXPERT group+ Software Keysight EasyEXPERT group+ GUI based characterization software is available on your PC to accelerate the characterization tasks. It supports efficient and repeatable device characterization in the entire characterization process from measurement setup and execution to analysis and data management either by interactive manual operation or automation across a wafer in conjunction with a semiautomatic wafer prober. EasyEXPERT group+ makes it easy to perform complex device characterization immediately with the ready-to-use measurements (application tests) furnished, and allows you the option of storing test condition and measurement data automatically after each measurement in a unique built-in database (workspace), ensuring that valu - able information is not lost and that measurements can be repeated at a later date. Finally, EasyEXPERT has built-in analysis capabilities and a graphical programming environment that facilitate the development of complex testing algorithms. Key features – Multiple measurement modes for quick setup and measurement execution (application test, classic test, and quick test) – Graphical display, automated analysis capabilities and data generation to Excel and image for analysis and reporting – Built-in database (workspace) records test data automatically and simplifies the data management without numerous data files – GUI-based control of the Keysight B2200A, B2201A and E5250A switching matrices – EasyEXPERT remote control function supports the remote measurement execution of application tests that are created on GUI interactively, via the LAN interface – Data back capability and various data protection feature for shared usage by multiple users – Characterization environment is available on user’s PC as a personal and portable analyzer environment. EasyEXPERT group+ can be installed on any PC as many as needed without additional charge. Application library EasyEXPERT group+ comes with the application tests conveniently organized by device type, application, and technology. You can easily edit and customize the furnished ap - plication tests to fit your specific needs. Application tests are provided for the following categories; they are subject to change without notice. Device Type Application Tests CMOS Transistor Id-Vg, Id-Vd, Vth, breakdown, etc. Bipolar Transistor Ic-Vc, diode, Gummel plot, breakdown, hfe, etc. Discrete device Id-Vg, Id-Vd, Ic-Vc, diode, etc. Power device Pulsed Id-Vg, pulsed Id-Vd, breakdown, etc. Nano Device Resistance, Id-Vg, Id-Vd, Ic-Vc, etc. Reliability test NBTI/PBTI, electro migration, hot carrier injection, J-Ramp, TDDB, etc.

15 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet Measurement modes and functions Operation Mode Application test mode The application test mode provides application oriented point- and-click test setup and execution. An application test can be se - lected from the library by device type and desired measurement, and then executed after modifying the default input parameters as needed. Available application tests can be adapted to config - ured resources. Classic test mode The classic test mode provides easy access to the instrument setup and measurement execution capabilities. Tracer test mode The tracer test mode offers intuitive and interactive sweep control using a rotary knob similar to a curve tracer. Just like an analog curve tracer, you can sweep in only one direction (useful for R&D device analysis) or in both directions (useful in failure analysis applications). Test set ups created in tracer test mode can be seamlessly and instantaneously transferred to classic test mode for further detailed measurement and analysis. Quick test mode A GUI-based Quick Test mode enables you to perform test se - quencing without programming. You can select, copy, rearrange and cut-and-paste any application tests with a few simple mouse clicks. Once you have selected and arranged your tests, simply click on the measurement button to begin running an automated test sequence. Other measurement characteristics Measurement control Single, repeat, append, and stop SMU setting capabilities Limited auto ranging, voltage/current compliance, power compliance, automatic sweep abort functions, self-test, and self-calibration Standby mode SMUs in “Standby” remain programmed to their specified output value even as other units are reset for the next measurement. Bias hold function This function allows you to keep a source active between measurements. The source module will apply the specified bias between measurements when running classic tests inside an application test, in quick test mode, or during a repeated measurement. The function ceases as soon as these conditions end or when a measurement that does not use this function is started. Current offset cancel This function subtracts the offset current from the current measurement raw data, and returns the result as the measure - ment data. This function is used to compensate the error factor (offset current) caused by the measurement path such as the measurement cables, manipulators, or probe card. Data display, analysis and arithmetic functions Data Display X-Y graph plot X-axis and up to eight Y-axes, linear and log scale, real time graph plotting. Scale: Auto scale and zoom Marker: Marker to min/max, interpolation, direct marker, and marker skip Cursor: Direct cursor Line: Two lines, normal mode, grad mode, tangent mode, and regression mode Overlay graph comparison: Graphical plots can be overlaid. List display Measurement data and calculated user function data are listed in conjunction with sweep step number or time domain sampling step number. Up to 20 data sets can be displayed. Data variable display Up to 20 user-defined parameters can be displayed on the graphics screen. Automatic analysis function On a graphics plot, the markers and lines can be automatically located using the auto analysis setup. Parameters can be auto - matically determined using automatic analysis, user function, and read out functions. Analysis functions Up to 20 user-defined analysis functions can be defined using arithmetic expressions. Measured data, pre-defined variables, and read out functions can be used in the computation, and the result can be displayed. Read out functions The read out functions are built-in functions for reading various values related to the marker, cursor, or line. Data export X-Y graph plot can be printed or stored as image data to clipboard or mass storage device. (File type: bmp, gif, png, emf). Graph and list data can be exported to Excel.

16 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet Arithmetic functions User functions Up to 20 user-defined functions can be defined using arithmetic expressions. Measured data and pre-defined variables can be used in the computation. The results can be displayed on the LCD. Arithmetic operators +, -, *, /, ^, abs (absolute value), at (arc tangent), avg (averaging), cond (conditional evaluation), delta, diff (differential), exp (expo - nent), integ (integration), lgt (logarithm, base 10), log (logarithm, base e), mavg (moving average), max,min, sqrt, trigonometric function, inverse trigonometric function, and so on. Physical constants Keyboard constants are stored in memory as follows: q: Electron charge, 1.602177E-19 C k: Boltzman’s constant, 1.380658E-23 ε (e): Dielectric constant of vacuum, 8.854188E-12 Engineering units The following unit symbols are also available on the keyboard: Data management Workspace (Built-in database) EasyEXPERT group+ supports the built-in database called “workspace”. Workspaces are created on a HDD, and they enable to manage and access all the measurement related data without handling numerous files. Every workspace supports the following features: – Access to measurement capabilities and data stored in the workspace. – Save/Import/Export measurement settings and data (application library, measurement settings, my favorite setup, and measurement data) – Recall the setup for measurement reproduction and data for analysis Data auto record/auto export EasyEXPERT group+ has the ability to automatically store the measurement setup and data within a workspace. It can also export measurement data in real time, in a variety of formats such as Excel (xls). Import/export files File type: Keysight EasyEXPERT format, XML-SS format, CSV format Data Protection EasyEXPERT group+ has various options to protect important data as follows. – Password protection (workspace, test definition and my favorite) – User level access control (engineer mode/operator mode) Workspace back-up and portability EasyEXPERT group+ has the ability to import/export a workspace for back-up and portability.

Precision Current - Voltage Analyzer Series Discontinued Advanced Device Analyzer Precision IV Analyzer Economic IV Analyzer B1500A B1505A E5270B E5262/63A E5260A B2900A Series SMU 4155B/C 4156B/C Classic Test I/V Sweep Yes Yes Yes Yes Yes Yes1 Multi-ch I/V Sweep Yes Yes Yes Yes Yes - I/V List Sweep Yes Yes Yes Yes Yes - I/V-t Sampling Yes Yes - - Yes Yes C-V Sweep Yes Yes - - - - SPGU Control Yes - - - - - GUI based switching matrix control Yes2 - Yes2 Yes2 Yes2 Yes2 Direct Control Yes Yes - - - - Application Test Yes Yes Yes Yes Yes Yes Tracer Test Yes (DC/Pulse) Yes (DC/Pulse) Yes (DC) Yes (DC) Yes (DC/Pulse) - Quick Test Yes Yes Yes Yes Yes Yes Oscilloscope view Yes3 Yes3 - - - - External instrument driver support LCR meter (4284A/E4980A) Yes Yes Yes Yes Yes Yes Pulse Generator (81110A) Yes Yes Yes Yes Yes Yes DVM (3458A) Yes Yes Yes Yes Yes Yes Prober control in Quick Test mode Yes

4 Yes4 Yes4 Yes4 Yes4 Yes4

Firmware requirement A.04.00 or later5 A.04.00 or later5 B.01.10 or later B.01.10 or later 1.0 or later HOSTC: 03.08 or later SMUC: 04.08 or later 1. PGU and VSU/VMU are supported. Differential voltage measurement of VMU is not supported. 2. B2200/01A and E5250A (with E5252A cards) are supported 3. Only available for supported modules. 4. Cascade Microtech Sumit 12000/S300 (Nucleus), Cascade Microtech (Suss MicroTec) PA200/PA300, and Vector Semiconductor VX-2000/VX-3000 5. The latest firmware version is strongly recommended to take full advantage of measurement capabilities. 17 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet EasyEXPERT group+ supported instruments and prerequisites Supported instruments and features

18 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet Recommended GPIB I/F Prerequisites Prerequisites to use the EasyEXPERT group+ on an external PC are as follows. IV Measurement features EasyEXPERT group+ Command based programming (FLEX command set) Spot measurement Yes Yes Pulsed spot measurement Yes Yes Staircase sweep Yes Yes Pulsed sweep Yes Yes Staircase sweep with pulsed bias Yes Yes Multi-channel sweep Yes Yes List Sweep Yes – Quasi-pulsed spot – Yes Linear search – Yes Binary search – Yes Measurements Modes Following table shows the measurement modes supported by the EasyEXPERT group+ and FLEX remote command set. Operating system and service pack Microsoft Windows Vista Business SP2 or later (32bit) Microsoft Windows 7 Professional SP1 or later (32bit/64bit) Microsoft Windows 8.1 Professional or later (32bit/64bit) Microsoft Windows 10 Pro or later (32bit/64bit) Processor Vista certified PC Windows 7 certified PC Windows 8.1 certified PC Windows 10 certified PC Supported language English (US) English (US) English (US) English (US) Memory 2 GB memory 2 GB memory 2 GB memory 2 GB memory Display XGA 1024 x 768 (SXGA 1280 x 1024 recommended) XGA 1024 x 768 (SXGA 1280 x 1024 recommended) XGA 1024 x 768 (SXGA 1280 x 1024 recommended) XGA 1024 x 768 (SXGA 1280 x 1024 recommended) HDD Installation: 1GB free disk space on the C drive Installation: 1GB free disk space on the C drive Installation: 1GB free disk space on the C drive Installation: 1GB free disk space on the C drive Test setup / result data storage: Free disk space more than 30GB is recommended Test setup / result data storage: Free disk space more than 30GB is recommended Test setup / result data storage: Free disk space more than 30GB is recommended Test setup / result data storage: Free disk space more than 30GB is recommended .NET Framework Microsoft .NET Framework

3.5 SP1

Microsoft .NET Framework Microsoft .NET Framework Microsoft .NET Framework IO Libraries Keysight IO Libraries Suite 16.2, 16.3, 17.1 update 1 or later (for the Online execution mode) Keysight IO Libraries Suite 16.2, 16.3, 17.1 update 1 or later (for the Online execution mode) Keysight IO Libraries Suite 16.2, 16.3, 17.1 update 1 or later (for the Online execution mode) Keysight IO Libraries Suite 17.1 update 1 or later (for the Online execution mode) Interface E5270B E5260A E5262/63A Keysight 82350B/C PCI 82351B PCIe 82537A /B USB National Instruments GPIB-USB-HS USB

Ordering Information

19 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet Model E5270B Precision IV Analyzer / 8 Slot Precision Measurement Mainframe E5270B contains triax cables for GNDU and SMU, the GNDU to Kelvin adapter, USB-GPIB interface and the EasyEXPERT group+ software install media. Cable length options E5270B-015 1.5m cable length E5270B-030 3.0m cable length Quick configuration options E5270B-A01 Four MPSMU package E5270B-A02 Two MPSMU and two HRSMU package E5270B-A03 Four HRSMU package Add-on module options E5270B-A10 Add one HPSMU E5270B-A11 Add one MPSMU E5270B-A17 Add one HRSMU E5270B-A28 Add atto sense and switch unit (ASU) Model E5270BU Upgrade kit for E5270B Module upgrade options E5270BU-080 Precision High Power Source/Monitor Unit Module (E5280B)/ No cable included E5270BU-081 Precision Medium Power Source/Monitor Unit Module (E5281B)/ No cable included E5270BU-087 High Resolution Source/Monitor Unit Module (E5287A)/ No cable included E5270BU-88A Atto Sense And Switch Unit (E5288A ASU) with 1.5 m Triax and Dsub Cable E5270BU-88B Atto Sense And Switch Unit (E5288A ASU) with 3 m Triax and Dsub Cable EasyEXPERT upgrade option E5270BU-SWS EasyEXPERT Extension support

20 | Keysight | Precision IV Analyzer/8 Slot Precision Measurement Mainframe - Data Sheet This information is subject to change without notice. © Keysight Technologies, 2004-2016 Published in USA, January 25, 2016 5989-1355EN www.keysight.com For more information on Keysight Technologies’ products, applications or services, please contact your local Keysight office. The complete list is available at: www.keysight.com/find/contactus Americas Canada (877) 894 4414 Brazil 55 11 3351 7010 Mexico 001 800 254 2440 United States (800) 829 4444 Asia Pacific Australia 1 800 629 485 China 800 810 0189 Hong Kong 800 938 693 India 1 800 11 2626 Japan 0120 (421) 345 Korea 080 769 0800 Malaysia 1 800 888 848 Singapore 1 800 375 8100 Taiwan 0800 047 866 Other AP Countries (65) 6375 8100 Europe & Middle East Austria 0800 001122 Belgium 0800 58580 Finland 0800 523252 France 0805 980333 Germany 0800 6270999 Ireland 1800 832700 Israel 1 809 343051 Italy 800 599100 Luxembourg +32 800 58580 Netherlands 0800 0233200 Russia 8800 5009286 Spain 800 000154 Sweden 0200 882255 Switzerland 0800 805353 Opt. 1 (DE) Opt. 2 (FR) Opt. 3 (IT) United Kingdom 0800 0260637 For other unlisted countries: www.keysight.com/find/contactus (BP-01-01-16) www.keysight.com/go/quality Keysight Technologies, Inc. DEKRA Certified ISO 9001:2008 Quality Management System myKeysight www.keysight.com/find/mykeysight A personalized view into the information most relevant to you. Three-Year Warranty www.keysight.com/find/ThreeYearWarranty Keysight’s committed to superior product quality and lower total cost of ownership. Keysight is the only test and measurement company with a three-year warranty standard on all instruments, worldwide. And, we provide a one-year warranty on many accessories, calibration devices, systems and custom products. Keysight Assurance Plans www.keysight.com/find/AssurancePlans Up to ten years of protection and no budgetary surprises to ensure your instruments are operating to specification, so you can rely on accurate measurements. From Hewlett-Packard through Agilent to Keysight For more than 75 years, we‘ve been helping you unlock measurement insights. Our unique combination of hardware, software and people can help you reach your next breakthrough. Unlocking measurement insights since 1939.

1939 THE FUTURE

Keysight Precision Current-Voltage Analyzer Series and Power Device Analyzer Series www.keysight.com/find/analyzer