DRE120

DRE120 CHINFA | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

Switching frequency Vi nom, Io nom KHz Characteristics Conditions min. typ. max. unit Isolation resistance Ambient temperature Input-Output, @ 500VDC Operating at Vi nom MΩ100 -40 o C+ 71 o All Specifications Typical At Nominal Line, Full Load, 25 C Unless Otherwise Noticed SPECIFICATION Derating (see derating curve) o % / C2.5o Vi nom, from +61 to +71 C Storage temperature Non operational + 85 o C-40 95Relative humidity Vi nom, Io nom Vi nom, Io min o Bellcore Issue 6 @40 C, GB % RH20 Temperature coefficient MTBF Altitude during operation o % / C m ± 0.03 24V Hours Hours + 12 VDC + 24 VDC 88 ~ 264 VAC 10 A 5 A 90% 91%

120 WATTS

88% 89%88 ~ 264 VAC

FEATURES

‧HIGH EFFICIENCY 91% ‧BUILT-IN ACTIVE PFC ‧150% PEAK LOAD CAPABILITY ‧SELV COMPONENTS DESIGN ‧PARALLEL FUNCTION (SWITCH SELECTABLE) ‧3 YEARS WARRANTY AC - DC DIN RAIL MOUNTABLE POWER SUPPLY INDUSTRIAL CONTROL EQUIPMENT SELECTION CHART MODEL LIST MODEL NO. INPUT VOLTAGE OUTPUT WATTAGE OUTPUT VOLTAGE OUTPUT CURRENT EFF. (typ.) Single Output Models EFF. (min.) DRE120 SERIES DRE 120 - 24 x Wattage 12 : 12V OUT 24 : 24V OUT Isolation voltage Input-Output VAC / VDC Input-FG 1,500 / 2,121 VAC / VDC 3,000 / 4,242 100 12V 5,000 465,000 480,000 EN 60950-1 500 / 710Output-FG VAC / VDC Free air convectionCooling Pollution degree 2 Characteristics Conditions min. typ. max. unit Io nomRated input voltage VAC AC in DC in Input voltage range Ta min ... Ta max, Io nom

264 VAC88

375120 VDC

Vi : 115 / 230 VAC, Io nomInput current 1.2 / 0.6 A Dimension Screw terminal type L124.5 x W40 x D123.6 L143.5 x W40 x D123.6 mm GENERAL Vi : 88 VAC, Io nomRated input current A1.8 INPUT SPECIFICATIONS A : SCREW TERMINAL TYPE B : DETACHABLE CONNECTOR TYPE Detachable connector type mm el min r Pr i a y www.chinfa.com sales@chinfa.com 2016.03.11 P1 IND. CONT. EQ. UL 508 HR Class I, Div 2 HR UL 60950-1 EN 60950-1 a EN 61558-1 EN 61558-2-16

Vi nom, Io max % Minimum load Vi nom % Output voltage accuracy (Adjusted before shipment) Line regulation % Load regulation Io nom, Vi min ...Vi max Vi nom, 0.8 Io nomVoltage trim range + 1 Characteristics Conditions min. unittyp. max. Power back immunity Vi nom, Io nom Capacitor load Vi nom, Io nom ± 1 11.4 22.5 VDC VDC 12V 24V 14.5 28.5 DC LOW indicator threshold after start up (Red LED) DC ON indicator threshold at start up (Green LED) Vi nom, Io nom Vi nom, Io nom VDC VDC VDC VDC 10 11.2 17.6 19.4 10 11.2 17.6 19.4 Inrush current Leakage current AVi : 115 / 230 VAC , Io nom Input-Output 0.25 3.5 o All Specifications Typical At Nominal Line, Full Load, 25 C Unless Otherwise Noticed SPECIFICATION Characteristics Conditions min. typ. max. unit DRE120 SERIES Power dissipation Vi : 230 VAC, Io nom W W 13.5 Input-FG mA mA Hold up time 30 12V 24V 7,000 12V 12V 24V 24V Power factor (Active) Vi : 230VAC, Io nom 0.96 VDC VDC Vi nomPeak power W180 ⴰF Parallel operation unit0.I Io min~0.9 Io max 3 %± 1 Vi nom, Io min ...Io nom single mode parallel mode ± 5 INPUT SPECIFICATIONS Turn on time Vi nom, Io nom with 7000 F CAPμ Vi nom, Io nom ms 1,500 ms ms1,000 Rise time Vi nom, Io nom with 7000 F CAPμ 150 msVi nom, Io nom Fall time msVi nom, Io nom 150 500 ms Ripple & noise mV100Vi nom, Io nom, BW = 20MHz Transient recovery time msVi nom, 1~0.5 Io nom 3 Vi nomRated continuous loading OUTPUT SPECIFICATIONS Line frequency Vi nom, Io nom 63 Hz47 12V 24V www.chinfa.com sales@chinfa.com 2016.03.11 P2 Vi nom, Io nom 12V 24V 5 A @ 24Vdc / 4.2 A @ 28.5 Vdc 10 A @ 12Vdc / 8.2 A @ 14.5 Vdc Efficiency Vi nom, Io nom, Po / Pi Up to 91%, See model list and typ efficiency curve Characteristics Conditions min. typ. max. unit Rated over load protection 160 %Vi nom (see typ current limited curve) Power Rdy (for 24V model only) Threshold voltage of contact closed(at start up) 17.6 19.4 VDC Electrical isolation 500 VDC Contact rating at 60 VDC 0.3 A Over voltage protection Vi nom, 0.8 Io nom (Shut-down protect) 15 16.5 V12V 30 33 V24V CONTROL AND PROTECTION Internal surge voltage protection VaristorIEC 61000-4-5 Output short circuit Hiccup mode Over temperature Detect on heat sink, shut down O/P voltage, recovers automatically after temperature goes down. o C90 100 Degree of protection IP20 T3.15A / 250VAC internalInput fuse

EN 60950-1, EN 61558-1, EN 61558-2-16 (meet EN 60204-1) CE EN 61000-6-3, EN 55022 Class B, EN 61000-3-2 Class D, EN 61000-3-3 EN 61000-6-2, EN 55024, EN 61000-4-2 Level 4, EN 61000-4-3 Level 3 EN 61000-4-4 Level 4, EN 61000-4-5 L-N Level 3, L / N-FG Level 4 EN 61000-4-6 Level 3, EN 61000-4-8 Level 4, EN 61000-4-11 ENV 50204 Level 2, EN 61204-3 Vibration resistance Shock resistance meet IEC 60068-2-6 (Mounting on rail : Random wave, 10-500 Hz, 2G, each along X, Y, Z axes 10 min / cycle, 60 min ) meet IEC 60068-2-27 (Half sine wave, 4G, 22ms, 3 axes, 6 Faces, 3 times for each face) APPROVALS AND STANDARDS MetalCase material Packing 0.65kg ; 24 / 16.5kg / 2.01CUFT 610gWeight MECHANISM & PIN CONFIGURATION mm [inch] 116.6 [4.59] 7.50 [0.3] PIN ASSIGNMENT V + 3, 4 5, 6 OUTINOTHER L N DC LO Vout ADJ. DC ON V - RDY A normal open relay contact for DC ON level control (Never connect except 24V model) Positive output terminal Negative output terminal Ground this terminal to minimize high-frequency emissions Input terminals (neutral conductor, no polarity at DC input) Input terminals (phase conductor, no polarity at DC input) Operation indicator LED DC LOW voltage indicator LED Trimmer-potentiometer for Vout adjustment PIN NO. Designation Description DRE120 SERIES S / P Single / Parallel select switch SPECIFICATION o All Specifications Typical At Nominal Line, Full Load, 25 C Unless Otherwise Noticed 40 [1.58] 6 1 40 [1.58] 6 1 7 9 124.50 [4.9] 124.50 [4.9] 143.50 [5.65] GENERAL TOLERANCE ±0.30[0.01] ±0.50[0.02] - - ++ Rdy DC LO DC ON Vout ADJ. S P N L DRE120 - - ++ Rdy DC LO DC ON S P Vout ADJ. DRE120 N L 7 9 CONSTRUCTION Easy snap-on mounting onto the DIN-Rail (TS35/7.5 or TS35/15), unit sits safeIy and firmly on the rail. INSTALLATION Ventilation / Cooling Normal convection All sides 25mm free space For cooling recommended Connector size range Screw terminal: 2 AWG24-10 (0.2~4mm ) flexible / solid cable, -Input connector can withstand torque at maximum 9 pound-inches. -Output connector can withstand torque at maximum 6 pound-inches. 8 m/m stripping at cable end recommends Detachable connector: 2 AWG24-12 (0.2~2.5mm ) flexible / solid cable, -Input connector can withstand torque at maximum 4.5 pound-inches. -Output connector can withstand torque at maximum 7 pound-inches. 4~5 m/m stripping at cable end recommendso Use copper conductors only, 60 / 75 C www.chinfa.com sales@chinfa.com 2016.03.11 P3 ISA 12.12.01 (Class I, Division 2, Groups A, B, C and D)

TYP. CURRENT LIMITED CURVE CIRCUIT SCHEMATIC DERATING CURVE TYP. EFFICIENCY CURVE Power out [ % ] 10 10025 EFFICIENCY [ % ] 7550

230 Vac

115 Vac

Output Voltage [ % ] 100 v t ‧Block diagram for DRE120 series Vo - Vo +L N Fuse PWM Controller Switching DeviceFilter Inrush Current Limiter Rectifier Rectifier Current Detection Opto - Isolation Reference & Error Amp. Y Vout ADJ. DC ON(Green LED) RDY 1) (Relay Contact) Active PFC Circuit Opto - Isolation DC LOW(Red LED) Error amp OVP Output Level Detection Single / Parallel select Note: 1) For 24V Model Only www.chinfa.com sales@chinfa.com 2016.03.11 P4 o Temperature [ C ] 100 71-40 Power out [ % ] Safe Operating Area Input Voltage[Vac ] 100 26488 Power out [ % ] 100 Safe Operating Area o Ta=60 C 100 120 130 140 150 160110 Output Current [ % ] Hiccup mode