DB01-FF150R12ME3G POWERINT | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 5
Technical content
IGBT-Driver.com Page 1 Data Sheet DB01-FF150R12ME3G Basic Board for Infineon EconoDUAL Modules FF150R12ME3G Abstract The DB01 -FF150R12ME3G is a basic board to be used with dual -channel driver 2SD316EI-12 for reliable driving and safe operation of Infineon IGBT modules FF150R12ME3G. The basic board DB01 -FF150R12ME3G (with driver 2SD316EI -12) is fully matched to IGBT module FF150R12ME3G. Its plug -and-play capability makes it ready to operate immediately after mounting. The user needs invest no effort in designing or adjusting it to a specific application. Product Highlights Applications Plug-and-play solution Three-phase inverters Suitable for FF150R12ME3G Motor drives No electrolytic capacitors UPS Extremely reliable; long service life Power-factor correctors Shortens application development time Wind-power converters Welding SMPS and many others
Page 2 CT-Concept.com Important: Please refer to the relevant manuals! This data sheet contains only product -specific data for the basic board. Information specific to the relevant driver can be found in the corresponding data sheet. A detailed description, must -read application notes and general data applicable to this driver family are found in: “Description and A pplication Manual, Dual-Channel Driver 2SD316EI for the EconoDUAL Modules ”. Dimensions Dimensions: 62 x 100 mm. Height including driver: 21 mm (30 mm with connector X1 and flat cable). Mounting principle: soldered onto an EconoDUAL IGBT module FF150R12ME3G. Absolute Maximum Ratings Parameter Remarks Min Max Units Input power per channel Note 1 3 W Switching frequency Note 2 69 kHz DC link voltage Note 3 800 V Operating temperature - 40 +85 °C Storage temperature - 40 +90 °C All data refer to +25°C unless otherwise specified
Electrical Characteristics
Short-circuit protection Remarks Min Typ. Max Units Vce-monitoring threshold Betw. aux. terminals 3.4 V Response time Note 4 10 µs Gate output Remarks Min Typ. Max Units Turn-on gate resistor Rg(on) 8.2 Ω
IGBT -Driver.com Page 3 Turn-off gate resistor Rg(off) 10 Ω Electrical insulation Test conditions Min Typ. Max Units Creep path between both channels 10 mm All data refer to +25°C unless otherwise specified Footnotes to the key data 1) The input power is limited by the on-board gate resistors. 2) If the specified max. switching frequency is exceeded, the gate resistors may overheat. 3) This limit is due to active clamping. Refer to the “Description and Application Manual, Dual-Channel Driver 2SD316EI for the EconoDUAL Modules”. 4) Pulse width of the direct output of the gate drive unit (excluding the gate-resistor delay). Important Notice The data contained in this product data sheet is intended exclusively for technically trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 747 -1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Disclaimer This data sheet speci fies devices but cannot promise to deliver any specific characteristics. No warranty or guarantee is given – either expressly or implicitly – regarding delivery, performance or suitability. CT-Concept Technology AG reserves the right to make modifications to its technical data and product specifications at any time without prior notice. The general terms and conditions of delivery of CT-Concept Technology AG apply.
Page 4 CT-Concept.com
Ordering Information
The general terms and conditions of delivery of CT-Concept Technologie AG apply. Related IGBT CONCEPT Driver Type # Infineon (eupec) FF150R12ME3G 2SD316EI-12 Connection CONCEPT Modular Cable Type # 2SD316EI-12 to DB01-FF150R12ME3G MIC01A (2 items per driver) Related IGBT CONCEPT Basic Board Type # Infineon (eupec) FF150R12ME3G DB01-FF150R12ME3G Information about Other Products For drivers adapted to other high-voltage or high-power IGBT modules Direct link: www.IGBT-Driver.com/go/plug-and-play For other drivers and evaluation systems Please click: www.IGBT-Driver.com © Manufacturer CT-Concept Technologie AG Intelligent Power Electronics Renferstrasse 15 CH-2504 Biel-Bienne Switzerland Tel. +41 - 32 - 344 47 47 Fax +41 - 32 - 344 47 40 E-mail Info@IGBT-Driver.com Internet www.IGBT-Driver.com Copyright 2005…2007 by CT -Concept Technologie AG - Switzerland. All rights reserved. We reserve the right to make any technical modifications without prior notice. Version of 2016-05-20
Click to View Pricing, Inventory, Delivery & Lifecycle Information: Power Integrations: DB01-FF150R12ME3G