6600686 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 8
Technical content
5-SHELF BOLTLESS SHELVING UNITS MODEL NO: CSR5100 PART NO: SEE TABLE PAGE 2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Shelving Unit. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. Please keep these instructions in a safe place for future reference. SCOPE These instructions cover the following models SPECIFICATIONS Description Model Part Number 5-Shelf 100kg Boltless Shelving (Light Grey) CSR5100LG 6600686 5-Shelf 100kg Boltless Shelving (Blue) CSR5100BL 6600688 5-Shelf 100kg Boltless Shelving (Red) CSR5100RP 6600690 Model Dimensions (W x D x H) Weight (Empty) Load per shelf (evenly distributed) All CSR5100 Units 900 x 400 x 1800 mm 16.9 kg 100 kg
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INVENTORY No Description Quantity AC o r n e r P o s t 8 B Shelf 5 C Long Beam 10 D Short Beam 10 E Centre Beam 5 F Post Joining Insert 4 G Plastic End Cap 8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ASSEMBLY ADVICE 1. Assemble on a strong, le vel surface. Avoid assembly on a domestic carpet. 2. Use a cloth or softwood block to protect the surface finish of the product when using a mallet. Strike the flat surface of each beam to prevent damage to the beam. 3. Always ensure that the rivets sit at the bottom of the keyhole slots. 4. It is recommended that the assemb ly should be done by two persons. 5. Always wear protective gloves wh en assembling the shelving unit. 6. The shelving unit is not recommended for outdoor use. ASSEMBLY INSTRUCTIONS TOOLS REQUIRED
- Rubber mallet or hammer Protective cloth/wood block The tabs of the beams will often enter the slots fully using just firm hand pressure but if they are too tight, you may require a rubber mallet to assist. If so, always use a cloth to protect the product paint finish. Tap gently with the mallet to drive the tabs of the beams fully into the slots in the post. Always strike the edge close to the post. 1. Use the short beams (D) to connect the front and rear posts together. NOTE: The short and long beams should be installed with the recessed edge uppermost to retain the shelf. Repeat this again to create the other end assembly, making surethat the corresponding beams are at the same height.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 2. Ensure the tabs lie flat against the surface of the post. 3. Join the two end assemblies together with the long beams (C). 4. Connect the support beams (E) to the long beams (C). First bend the tabs 90 degrees to pass them through the slots in the long beams. The tab initially lays flat against the long beam (C). 5. Next, bend the tab back through 180 degrees to grip the long beam. Use a screwdriver or similar tool to bend the tabs. 6. Finally bend the tab again through 90 degrees the opposite way, to seat tightly against the support beam (E). 7. Ensure there is no movement between the beams.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 8. Fit post joining inserts (F) into the posts (A), ensuring that the inserts are fitted with their keyholes to match those of the posts. 9. Construct the upper end assemblies onto the post inserts (F) before adding more long beams and support beams as previously to complete the framework. 10. Lay the shelf panels (B) into position. Always assemble the top shelf at the highest possible position. 11. Insert the plastic end caps (G) into the end of each post (A). 12. We recommend that the shelvng be secured to an adjacent wall using typical wall insert plugs and screws (not supplied) aligned with the assembly slots in the posts.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GENERAL SAFETY RULES 1. Always maintain equipment in g ood condition for the best/safest performance. 2. Never exceed the maximum load for th ese shelving units as stated in the specification. 3. Never use these units if they are damaged. 4. Always load small, stable items on t he top shelves, heavier and bulky items should be stored on the lower shelves. 5. Always distribute heavy load s evenly across the shelves. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. ENVIRONMENTAL PROTECTION Do not dispose of old products or damaged parts with general household waste. All tools, accessories and packaging no longer required should be sorted, taken to a recycling centre and disposed of appropriately.