6600800 CLARKE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 12

Technical content

ORIGINAL INSTRUCTIONS GC06/18 ISS 1 BOLTLESS SHELVING UNITS MODEL NO: CSM5150 & CSM5350 PART NO: SEE TABLE PAGE 2

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Shelving Unit. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. Please keep these instructions in a safe place for future reference. SCOPE These instructions cover the following models SPECIFICATIONS Description Model Part Number CSR5150 units 5-Shelf Boltless Shelving (Silver) CSM5150S 6600800 5-Shelf Boltless Shelving (Red) CSM5150RP 6600802 5-Shelf Boltless Shelving (Blue) CSM5150BP 6600804 5-Shelf Boltless Shelving (Dark Grey) CSM5150B 6600812 5-Shelf Boltless Shelving (Galvanized) CSM5150G 6600816 CSR5350 units 5-Shelf Boltless Shelving (Silver) CSM5350S 6600806 5-Shelf Boltless Shelving (Red) CSM5350RP 6600808 5-Shelf Boltless Shelving (Blue) CSM5350BP 6600810 5-Shelf Boltless Shelving (Dark Grey) CSM5350B 6600814 5-Shelf Boltless Shelving (Galvanized) CSM5350G 6600818 Model Dimensions (W x D x H) Weight (Empty) Load per shelf evenly distributed All 5150 units 800 x 300 x 1500 mm 12.2 kg 150 kg All 5350 units 900 x 400 x 1800 mm 18.1 kg 350 kg

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ASSEMBLY ADVICE 1. Assemble on a strong, le vel surface. Avoid assembly on a domestic carpet. 2. Use a cloth or softwood block to protect the surface finish of the product when using a mallet. Strike the flat surface of each beam to prevent damage to the beam. 3. Always ensure that the tabs enter fully into the slots. 4. It is recommended that the assemb ly should be done by two persons. 5. Always wear protective gloves wh en assembling the shelving unit. The shelving unit is not recommended for outdoor use.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INVENTORY No Description Quantity AP o s t 8 B Shelf 5 C Long Beam 10 D Short Beam 10 ES u p p o r t B e a m 5 F Post Joining Insert 4 G Plastic End Cap 4

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ASSEMBLY INSTRUCTIONS TOOLS REQUIRED

  • Rubber mallet or hammer  Protective cloth/wood block ASSEMBLY The tabs of the beams will often enter the slots fully using just firm hand pressure but if they are too tight, you may require a rubber mallet to assist. If so, always use a cloth to protect the product paint finish. Tap gently with the mallet to drive the tabs of the beams fully into the slots in the post. Always strike the edge close to the post. 1. Use the short beams to connect th e front and rear posts together. NOTE: The short and long beams should be installed with the recessed edge uppermost to retain the shelf.  Repeat this again to create the other end assembly, making sure that the corresponding beams are at the same height. 2. Ensure the tabs lie flat against the surface of the post.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 3. Join the two end assemblies together with the long beams. 4. Fit post joining inserts into the posts, ensuring that the inserts are fitted with their tabs to match the slots of the posts.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com Construct more upper end assemblies onto the post inserts before adding more beams as previously to complete the framework. 5. Connect the support beams to the long beams. First bend the flexible tabs to 90 degrees to pass them through the slots in the long beams.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com  The tab initially lays fl at against the long beam. 6. Next, bend the tab back through 180 degrees to grip the long beam.  Use a screwdriver or similar tool to bend the tabs. 7. Finally bend the tab again through 90 degrees the opposite way, to seat tightly against the support beam. 8. Ensure there is no movement between the beams. 9. Lay the shelf panels into position.  Always assemble the top shelf at the highest possible position. 10. Fit the plastic end caps to the end of each post.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com We recommend that the shelving be secured to an adjacent wall using typical wall insert plugs and screws (not supplied) aligned with the slots in the posts.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GENERAL SAFETY RULES 1. Always maintain shelving in g ood condition for the best/safest performance. 2. Never exceed the maximum load for th ese shelving units as stated in the specification. 3. Never use these shelving units if they are damaged. 4. Always load small, stable items on t he top shelves, heavier and bulky items should be stored on the lower shelves. 5. Always distribute heavy load s evenly across the shelves.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. ENVIRONMENTAL PROTECTION Do not dispose of old products or damaged parts with general household waste. All tools, accessories and packaging no longer required should be sorted, taken to a recycling centre and disposed of appropriately.