7624016 CLARKE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 8

Technical content

ORIGINAL INSTRUCTIONS GC0 1/26- rev 1

1 TONNE SCISSOR JACK

MODEL NO: CSJ1000 PART NO: 7624016

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Scissor Jack. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. LIFTING OPERATIONS AND LIFTING EQUIPMENT REGULATIONS 1998 (LOLER) This jack, depending on use, may fall within the scope of LOLER. It is the owner’s responsibility to determine whether or not it does and, if so, to comply with any applicable requirements in LOLER, for having the jack thoroughly examined. SPECIFICATION Rated Load 1.0 Tonne/1000kg Min height of saddle 82 mm Max height of saddle 329 mm Lifting range under load 200-329 mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SAFETY PRECAUTIONS 1. Ensure that the jack is in good working order. Have any damaged parts repaired or replaced immediately. Use genuine Clarke parts only. The use of unauthorised parts may be dangerous and will invalidate the warranty. 2. Operate the jack in a suitable, well lit work area. 3. Keep the work area clean and tidy and free from unrelated items. 4. Use the jack on level and solid ground, preferably concrete. Avoid soft/unmade ground as the jack may sink in. 5. Ensure the vehicle handbrake is engaged, the engine/motor is switched off and the transmission is in 1st or reverse gear. (or park for automatics) 6. Ensure a minimum distance of 0.5 m between vehicle and static objects such as doors, walls, etc, to allow for the vehicle tilting. 7. Only place the jack under those lifting points recommended by the vehicle manufacturer (see vehicle handbook). 8. Check the lifting point is rigid and centred on the jack saddle. 9. Ensure there are no passengers in the vehicle. 10. Place chocks under the wheels of the vehicle. 11. Ensure all non-essential persons keep a safe distance whilst the jack is in use. 12. Use suitable capacity axle stands under the vehicle before proceeding with any task. 13. Ensure there are no personnel or obstructions under the vehicle before lowering. 14.Use the jack for lifting only, NOT for supporting the vehicle. 15. Take care not to trap fingers in the moving parts of the jack. 16.DO NOT operate the jack if damaged. 17.DO NOT work under the vehicle until axle stands have been correctly positioned. 18.DO NOT allow personnel to operate the jack unless they have read these safety precautions. 19.DO NOT use the jack for purposes other than that for which it is designed. 20.DO NOT exceed the rated capacity of the jack. 21.DO NOT jack up a vehicle if there is a risk of spillage of fuel, battery acid or other dangerous substances. 22.DO NOT allow the vehicle to move while supported by the jack.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 23. Ensure that you can see the saddle and jacking point throughout the jacking operation in case there is any relative movement. 24.NEVER tamper with the product or modify it in any way, as this could prove to be dangerous and will invalidate the guarantee. Only use the product for the purpose for which it is intended. 25. When not in use, store the jack, fully lowered, in a safe, dry, childproof area. OPERATING INSTRUCTIONS 1. Prepare the vehicle as mentioned in the safety precautions ensuring the ground on which the jack is to stand is level and solid. 2. Position the jack saddle under the vehicle manufacturers recommended lifting point. 3. No responsibility can be accepted for incorrect use of the jack. LIFTING THE VEHICLE 1. Turn the handle clockwise to bring the jack saddle into contact with the recommended lifting point. 2. Ensure the jack is vertical before continuing to turn the handle clockwise and raising the vehicle to the required working height. Turn the handle slowly and evenly to ensure no sudden movements of the vehicle. WARNING: IT IS VERY DANGEROUS TO GO UNDER A VEHICLE WHICH IS SUPPORTED BY A JACK EVEN IF ADDITIONAL SUPPORTS ARE USED. DO NOT GO UNDER A VEHICLE UNLESS IT IS SUPPORTED BY ADEQUATELY RATED AXLE STAND WARNING: BEFORE LIFTING, ENSURE THE SAFETY PRECAUTIONS ARE STRICTLY FOLLOWED.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com LOWERING THE VEHICLE 1. Slowly turn the handle anti-clockwise to lower the vehicle. MAINTENANCE IMPORTANT: Only fully qualified personnel should attempt maintenance or repair. 1. Keep the jack clean and lubricate all moving parts with oil on a regular basis. 2. Before each use check for broken, cracked, bent, or loose parts, or any visible damage to welds, saddle, frame and all parts including pins and other fasteners. If any suspect item is found remove jack from service and take necessary action to remedy the problem. WARNING: ALWAYS LOWER IN A SLOW AND CONTROLLED MANNER AND ENSURE THERE ARE NO PERSONS OR OBSTACLES BENEATH THE VEHICLE, OR IN THE PATH OF ITS DESCENT.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com PARTS LIST & DIAGRAM No Description No Description

1 Saddle 8 Base

2 Upper pin 9 Bracket

3 Upper arm 10 Bearing

4 Spacer 11 Operation direction label

5 Threaded rod 12 Label

6 Lower arm 13 Handle

7 Lower pin

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY