6600502 CLARKE | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 8

Technical content

ORIGINAL INSTRUCTIONS GC0219 - rev 4 INDUSTRIAL SHELVING MODEL NO: CS4700 & CS4700BO PART NO: 6600502 & 6600610

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Shelving Unit. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. Keep these instructions for future reference. Please keep these instructions in a safe place for future reference. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. ENVIRONMENTAL PROTECTION Do not dispose of this product with general household waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of appropriately.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SPECIFICATIONS Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. LIST OF COMPONENTS When unpacking, check for damage and/or shortages etc. Any found should be reported to your CLARKE dealer where the product was originally purchased. This shelving unit should include the following: 2 x Upright Frames 8 x Beams 16 x Deck Supports 4 x Deck Panels 1 x Instruction Manual (this document) TOOLS REQUIRED Rubber mallet or hammer. Protective cloth/wood block. All CS4700 models Dimensions (W x D x H) 1940 x 610 x 1830 mm Product weight 95 kg Load per shelf 800 kg (evenly distributed)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GENERAL SAFETY RULES 1. Always maintain the shelving in good condition for greater safety. 2. Never exceed the maximum load for this product. 3. Never use this product if damaged. 4. Always load small, stable items on t he top shelves, heavier and bulky items should be stored on the lower shelves. COMPONENT PARTS

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ASSEMBLY TIPS 1. Assemble the unit on a strong, le vel surface. Avoid assembly on soft surfaces. 2. Use a cloth or softwood block to protect the surface finish of the product when using a hammer. Hit the flat surface of each cross-beam to prevent damage to the beam. 3. Always ensure that the tabs sit at the bottom of the tapered slots. 4. It is recommended that the assemb ly should be done by two persons. 5. This product is not recommended for outdoor use. ASSEMBLY INSTRUCTIONS 1. Take a beam (B) and attach to one of the upright frames by inserting the two clips on the bracket into the keyholes of the frame column. Present them from the outside. 2. Drive the tabs right to the bottom of the slots by tapping the beam near the joint with a rubber mallet to lock the pieces together as shown in Fig 1.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 3. Repeat this step with the second upright frame (A) at the other end of the beam, making sure that the clips are at the same level. 4. Repeat with the other beam (B), making sure that the beams are level. NOTE: Take care not to strike so hard as to damage the beams.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 5. Repeat steps 2 to 4 to attach the next set of beams (B) at the same level to form the second and third shelf frames as shown in fig 2. NOTE: The units are adjustable in 3” increments. 6. Ensure the last two beams (B) are set into the top two keyholes of the upright frames as shown in Fig 3. 7. Position the deck supports (C) to span between the beams (B), engaging the support end in the socket provided in the beam. Four supports per shelf are required at the positions shown. 8. Place the deck panels (D) onto t he deck supports, resting on the top flange of the beams. Make sure the deck panels sit properly between the beamsand lay flush as shown in Fig 4. 9. Periodically inspect the unit to en sure the beams are seated correctly and are firmly connected to the columns. Take care not to overload the shelves.