6600728 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 8
Technical content
4-SHELF INDUSTRIAL BOLTLESS SHELVING MODEL NO: CS4600BO & CS41000BO PART NO: SEE TABLE PAGE 2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE Shelving Unit. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. Please keep these instructions in a safe place for future reference. SCOPE These instructions cover the following models SPECIFICATIONS Description Model Part Number 4-Shelf 600kg Boltless Shelving (Blue/orange) CS4600BO 6600728 4-Shelf 1000kg Boltless Shelving (Blue/orange) CS41000BO 6600730 Model Dimension (W x D x H) Weight (Empty) Load per shelf (evenly distributed) 4-Shelf 600kg Shelving 2000 x 600 x 2000 mm 71.8 kg 600 kg 4-Shelf 1000kg Shelving 2000 x 800 x 1800 mm 72.3 kg 1000 kg
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INVENTORY No Description Quantity AP o s t 4 BL o n g B e a m 8 CS h o r t B e a m 6 D Support Beam 20 E Shelf 4 F Foot (already fitted) 4
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ASSEMBLY INSTRUCTIONS 1. Assemble on a strong, le vel surface. Avoid assembly on a domestic carpet. 2. Use a cloth or softwood block to protect the surface finish of the product when using a mallet. Strike the flat surface of each beam to prevent damage to the beam. 3. Always ensure that the rivets sit at the bottom of the keyhole slots. 4. It is recommended that the assemb ly should be done by two persons. 5. Always wear gloves when assembling these units. 6. The shelving unit is not recommended for outdoor use. TOOLS REQUIRED
- Rubber mallet or hammer Protective cloth/wood block ASSEMBLY PROCEDURE 1. Assemble the supporting beams as follows. 2. The tabs of the beams will often enter the slots fully using just firm hand pressure but if they are too tight, you may require a rubber mallet to assist. If so, always use a cloth to protect the paint finish. 3. Tap gently with the mallet to drive the tabs of the beams fully into the slots in the post. Always strike the edge close to the post. 4. Use the short beams (C) to connect the front and rear posts together as in Fig 2. The edge with the wider flange should be installed uppermost to support the shelf. Leave a gap of 220mm below the bottom beam and the ground. Leave 100mm gap from the top beam and the top of the posts.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 5. Repeat this again to create the other end assembly, making sure that the corresponding beams are at the same height. 6. Join the two end assemblies together with the long beams (B) as in Fig 3. The beams should be spaced equally with a gap of 500mm between each one and the top beam will be level with the top of the posts. 7. Connect the support beams (E) to the long beams (C). First bend the tabs 90 degrees to pass them through the slots in the long beams. The tab initially lays flat against the long beam (C). 8. Next, bend the tab back through 180 degrees to grip the long beam. Use a screwdriver or similar tool to bend the tabs. 9. Finally bend the tab again through 90 degrees the opposite way, to seat tightly against the support beam. Ensure there is no movement between the beams. 10. Lay the shelf panels (E) into position.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 11. We recommend that the racking be secured to an adjacent wall using typical wall insert plugs and screws (not supplied) aligned with the assembly slots in the posts. GENERAL SAFETY RULES 1. Always maintain equipment in g ood condition for the best/safest performance. 2. Never exceed the maximum load for th ese shelving units as stated in the specification. 3. Never use these units if they are damaged. 4. Always load small, stable items on t he top shelves, heavier and bulky items should be stored on the lower shelves. 5. Always distribute heavy load s evenly across the shelves. 6. Always locate on a strong, level, floor surface. Allow adequate working space ENVIRONMENTAL PROTECTION Do not dispose of old products or damaged parts with general household waste. All tools, accessories and packaging no longer required should be sorted, taken to a recycling centre and disposed of appropriately.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights.