6462019 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 24
Technical content
OPERATION & MAINTENANCE INSTRUCTIONS DL0621 - ISS 1 ORIGINAL INSTRUCTIONS 82MM ELECTRIC PLANER MODEL NO: CEP720B PART NO: 6462019
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for selecting this Clarke 82mm Electric Planer. The electric planer is intended for removing surface material with a rotating blade that is parallel to the base plate. Before using the device, please read this manual thoroughly and carefully follow all instructions given. This is for your own safety and that of others around you, and is also to help you achieve a long and trouble free service from your new tool. GUARANTEE The product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Your receipt is required as proof of purchase. This guarantee is invalid if the product is found to have been abused, tampered with, or not used for the purpose for which it was intended. Faulty goods must be returned to their place of purchase, do not return it to us without prior permission. This guarantee does not effect your statutory rights. ENVIRONMENTAL RECYCLING POLICY Through purchase of this product, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE. In effect, this means that this product must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GENERAL POWER TOOL SAFETY WARNINGS Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated electric planer. WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which can ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY 1. Power tool plugs must match the outlet. Do not modify the plug in any way. DO NOT use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 2. AVOID body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 3. DO NOT abuse the cord. DO NOT use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 4. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. 5. IP20 RATED ONLY.DO NOT expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 6. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. WARNING: READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. FAILURE TO FOLLOW THE WARNINGS AND INSTRUCTIONS CAN RESULT IN ELECTRIC SHOCK, FIRE AND/OR INJURY.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com PERSONAL SAFETY 1. Stay alert, watch what you are doing and use common sense when operating a power tool. DO NOT use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools can result in personal injury. 2. Use personal protective equipment. ALWA YS wear eye and ear protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. 3. Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. 4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool can result in personal injury. 5. DO NOT overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 6. Dress correctly. DO NOT wear loose clothing or jewellery. Keep your hair, and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and correctly used. Use of dust collection can reduce dust-related hazards. POWER TOOL USE AND CARE 1. DO NOT force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 2. DO NOT use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 4. Store idle power tools out of the reach of children and DO NOT let persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that can affect the power tool's
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 6. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. SERVICE 1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. PLANER SAFETY WARNINGS 1. Wait for the blade to stop before setting the planer down. An exposed rotating blade can strike the worktop, leading to possible loss of control and injury. 2. Hold the planer by insulated gripping surfaces, because the blade may contact its own cable. Cutting a “live” wire may make exposed metal parts of the planer “live” and could give the operator an electric shock. 3. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the workpiece by your hand or against the body leaves it unstable and can lead to loss of control. 4. Always start the planer before the blade is in contact with the workpiece and let the blade reach full speed. The tool can vibrate or chatter if blade speed is too slow at beginning of the cut and possibly kickback. 5. Check the workpiece for nails or screws. If there are nails/screws, either remove or set them well below intended finished surface. Kickback, damage to the blades and personal injury can result If the planer blades strike objects like nails. 6. Unplug the planer before changing accessories. Before plugging the planer in, check that the trigger lock is “OFF”. Accidental start-ups can occur if the planer is plugged in while changing an accessory. 7. After changing blades, rotate the blade drum to make sure the blades are not hitting any part of the housing and that the blade locking screws are tight. Spinning blades could strike the tool housing and damage the tool as well as causing possible injury. 8. ALWA YS hold the planer firmly with both hands for maximum control. 9. DO NOT pull the planer backward over the workpiece. Loss of control can occur.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 10. DO NOT put your fingers or any objects into the shavings exhaust port or clean out shavings while the tool is running. Contact with blade will cause injury. 11. Remove the plug from the power source if it becomes necessary to remove woodchips. The blades are hidden from view and you may be cut if the blade is touched. 12. DO NOT use dull or damaged blades. Sharp blades must be handled with care. Damaged blades can snap during use. Dull blades require more force to push the tool, possibly causing the blade to break. SAFETY SYMBOLS Read instruction manual before use Wear safety glasses Wear ear defenders Wear protective gloves
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ELECTRICAL CONNECTIONS This tool is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. If the plug need changing, make sure that a plug of identical specification is used. If the colours of the wires in the power cable do not correspond with the markings on the terminals of your plug, proceed as follows. C o n n e c t t h e blue wire to the terminal which is marked N. C o n n e c t t h e brown wire to the terminal which is marked L. We recommend that this machine is connected to the mains supply via a Residual Current Device (RCD) If in doubt, consult a qualified electrician. DO NOT attempt any repairs yourself This symbol indicates that this is a Class II product, and does not require an earth connection. EXTENSION CABLE Always use an approved extension cable suitable for the power rating of this tool (see specifications), the conductor size must be at least the same size as that on the machine, or larger. When using a cable reel, always unwind the cable completely. WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS FULLY BEFORE CONNECTING THE TOOL TO THE MAINS SUPPLY. WARNING: THE WIRES IN THE CABLE ARE COLOURED AS FOLLOWS: BLUE = NEUTRAL BROWN = LIVE Plug must be BS1363/A approved. Always fit make sure that the outer sheath of Neutral (Blue) Live (Brown) a 13 Amp the cable is firmly held by the clamp fuse.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OVERVIEW
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OPERATION USING THE SAFETY KICKSTAND The safety kickstand on the rear of the planer swings down to help keep the blade from touching the workbench when the planer is not being used. The kickstand is designed to swing up and out of the way when the back of the planer crosses the leading edge of the workpiece. DUST EXTRACTION The wood shavings can be set to flow from either side of the tool to suit the task at hand. 1. Set the extraction guide switch to point towards the extraction port that you wish the chips to flow towards. 2. If desired, attach the dust bag by sliding the nozzle onto the appropriate chip extraction port. For efficient operation, empty the dust bag when it is no more than half full, allowing for better airflow through the bag. 3. You can also connect your planer to a suitable dust extraction system through the extraction port. Hose adaptors (not included) may be needed depending on the size of your dust hose. WARNING: SHAVINGS MAY JAM IN THE DUST EXTRACTION PORT WHEN CUTTING DAMP WOOD. DO NOT INSERT YOUR FINGER INTO THE DUST EXTRACTION PORT. CLEAN OUT THE SHAVINGS WITH A STICK, BUT ONLY WHEN THE BLADE HAS STOPPED RUNNING AND THE TOOL HAS BEEN DISCONNECTED FROM THE POWER SOURCE.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SWITCHING ON/OFF The planer has a trigger lock to prevent accidental start-ups. 1. To turn the planer on, push the trigger lock and then squeeze the trigger switch. 2. To switch off, release the trigger switch. ADJUSTING THE DEPTH OF CUT 1. Rotate the depth adjustment knob until the indicator arrow aligns with the desired cutting depth on the depth gauge. The minimum cutting increment is 0.25 mm. The maximum cutting depth of the planer is 3 mm. NOTE: For optimal performance, set the cutting depth to 0.5 mm and make multiple cuts until you reach the depth required. CAUTION: ALWAYS ENSURE THAT THE NUMBER ON THE DEPTH GAUGE IS AT THE “0” POSITION WHEN THE PLANER IS NOT IN USE. HOWEVER, EVEN AT “0”, A SLIGHTLY PROTRUSIVE BLADE COULD STILL MAKE CONTACT DEPENDING ON HOW THE BLADE WAS INSTALLED. ENGAGE THE SAFETY KICKSTAND TO PREVENT THE BLADE FROM TOUCHING THE WORKBENCH.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GRAIN DIRECTION The planer must always cut in the same direction as the grain of the wood. There are six sides to every board: two face grains, two side/edge grains, and two end grains. When planing the face and side/ edge grain, always plane in the direction of the grain. WARNING: DO NOT PLANE ACROSS THE GRAIN OF THE WOOD. DO NOT PLANE END GRAIN AS THE WOOD WILL SPLINTER.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com USING THE PLANER 1. Secure the workpiece to a stable platform. 2. Hold the planer firmly with both hands. 3. Rest the front shoe flat on the workpiece surface, ensuring that the blades do not make contact with the workpiece. 4. Press the trigger switch and squeeze trigger switch and wait for the blade to reach full speed. 5. Move the planer gently forward along the grain of the wood. Apply pressure on the front of the planer at the beginning of the stroke and at the rear of the planer towards the end of the stroke. NOTE: The feed rate and the depth of cutting determine the quality of the finish. Reduce the depth of the cut to achieve a smoother finish. 6. Push the planer beyond the edge of the workpiece without tilting it downwards. 7. Release trigger switch and wait for the blade to stop before setting the planer down. WARNING: WEAR SAFETY GOGGLES AT ALL TIMES. USE EAR PROTECTION SUCH AS PLUGS OR EAR DEFENDERS DURING EXTENDED PERIODS OF OPERATION. WEAR A DUST MASK.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com MAKING A CHAMFER The V-groove in the front shoe allows you to create a sloping edge along the corner of your workpiece. 1. Make sure that the workpiece is secured to a stable platform. 2. Align the V-groove in the front shoe of the planer with the corner edge of the workpiece. Be sure the blades are not touching the workpiece. Place some weight on the depth adjustment knob so that the V-groove is absolutely flat on the edge to be beveled. 3. Press the trigger switch and squeeze trigger switch and wait for the blade to reach full speed. 4. Push the planer forward along the grain of the wood with steady pressure on the front shoe. Push the planer beyond the edge of the workpiece without tilting it downwards. 5. Release trigger switch the and wait fo r the blade to stop before setting the tool down.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com USING THE PARALLEL GUIDE FENCE The parallel guide fence ensures that the planer travels parallel to the edge of the wood, providing a straight cut at your desired cutting width. This feature is helpful for planing door edges, wood trim and boards. To attach the parallel guide fence: 1. Disconnect the planer from the power source. 2. Attach the parallel guide fence to the left-hand side of the planer using the lock knob. 3. Loosen the wing nut on the parallel guide fence and slide the fence to set the desired cutting width indicated by the width gauge. Retighten the wing nut. NOTE: To ensure a square cut, measure the front and back of the fence and use a square to make sure the guide is set straight. 4. Rest the front shoe flat on the workpiece surface and position the fence firmly against the edge of the workpiece Follow instructions on page 12 to perform your cut.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com USING THE RABBETING DEPTH GUIDE The rabbeting depth guide can be adjusted anywhere from 0 to 18mm above the base of the planer. To attach the rabbeting depth guide: 1. Disconnect the planer from the power source. 2. Attach the rabbeting depth gauge to the right-hand side of the planer using the lock knob. 3. Position the rabbeting depth gauge to the desired height against the depth indication mark on the side housing. Tighten the lock knob. 4. If desired, use the parallel guide fence in conjunction with the rabbeting depth guide to create a straight rabbeting cut. 5. Make multiple progressive cuts to achieve the total cutting depth. The required rabbeting depth is achieved when the depth gauge is flush with the unplaned section of the workpiece to the right-hand side of the tool. NOTE: The rabbeting depth gauge allows only approximate depth settings. If it is necessary to rabbet to a precise depth, plane a scrap piece of wood, measure the rabbeted depth, and adjust the setting as necessary.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com REMOVING OR INSTALLING PLANER BLADES The condition of the blades will affect the precision of the cuts. Dull blades will tear wood fibers and produce fuzzy surfaces. NOTE: Blades on this planer are reversible and must always be reversed or replaced as a matched set. Unbalanced blades can cause vibration and poor planing action while shortening the life of the blade and the tool. Keeping a spare set of blades on hand is recommended. 1. Disconnect the planer from the power source. 2. Turn the planer upside down and rotate the blade drum to expose the clamping screws. 3. Loosen the three clamping screws using the onboard blade wrench stored in the planer body. WARNING: PLANER BLADES ARE SHARP AND FRAGILE. WEAR PROTECTIVE GLOVES TO PROTECT YOUR HANDS. HANDLE THE BLADES CAREFULLY TO AVOID PERSONAL INJURY OR DAMAGE TO THE BLADES. WARNING: DO NOT ATTEMPT TO SHARPEN OR USE RESHARPENED BLADES. WARNING: MAKE SURE THAT THE TOOL IS UNPLUGGED FROM THE POWER SUPPLY BEFORE MAKING ADJUSTMENTS OR INSTALLING OR REMOVING BLADES. CAUTION: THE BLADE DRUM CAN ROTATE AS YOU’RE DOING THIS SO BE CAREFUL NOT TO CONTACT THE BLADE WITH YOUR HAND. IF THE SCREW IS DIFFICULT TO LOOSEN, TRY TIGHTENING IT A LITTLE AND THEN LOOSEN IT.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 4. Hold the blade drum in place and carefully slide out the blade. You can also use a wooden block to push the blade out of the blade drum. 5. Clean out all foreign matter adhering to the blade drum and the blade using a brush or compressed air, making sure eye protection is worn. 6. Each planer blade has two cutting edges and can be reversed when one of the cutting edges becomes dull or chipped. If one edge is dull, reverse the blade. If both edges are dull, remove the old blade and replace it with a new one. 7. Slide the blade with the good side exposed into the blade retainer of the blade drum. Make sure the blade is positioned in the center of the blade drum. The flat side of the blade must be facing the front of the planer and the ridged side of the blade must be facing the back of the planer. 8. To ensure an even cut, the blade should align with the outside edge of the front and rear shoes. Place a straight edge along the outside edge of the front and rear shoe. Slide the planer blade to just contact the straight edge. 9. The blades must be mounted so that the cutting edge is absolutely level (parallel to the surface of the rear shoe). Check that both ends of the blade protrude evenly from the blade retainer of the blade drum.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com NOTE: The planed surface will end up rough and uneven if blades are not set correctly or securely. 10. Tighten the clamping screws using the blade wrench, ensuring that all three screws are tightened evenly. 11. Repeat steps 2 - 10 for the installing/changing the second blade. It is important to reverse or replace the two blades at the same time so they are balanced with one another. Both blades must be set to the same cutting level and alignment, otherwise the planed surface will be rough and uneven. MAINTENANCE AND SERVICING CLEANING Keep the planer clean of any wood chips, dust, dirt or debris. Ventilation openings must be kept clean and free of foreign matter. The planer can be cleaned most effectively with compressed dry air. Always wear safety goggles wh en cleaning power tools with compressed air. CAUTION: TIGHTEN ALL CLAMPING SCREWS CAREFULLY WHEN ATTACHING THE BLADES TO THE PLANER. A LOOSE CLAMPING SCREWS CAN BE EXTREMELY DANGEROUS. CHECK REGULARLY TO MAKE SURE THAT ALL SIX CLAMPING SCREWS ARE TIGHTENED SECURELY. WARNING: MAKE SURE THAT THE PLANER IS TURNED OFF AND UNPLUGGED FROM THE POWER SOURCE BEFORE CLEANING AND MAINTENANCE OPERATIONS. WARNING: REFER TO YOUR CLARKE DEALER IF INTERNAL MAINTENANCE IS NECESSARY. WARNING: CERTAIN CLEANING AGENTS AND SOLVENTS DAMAGE PLASTIC PARTS. SOME OF THESE ARE: GASOLINE, CARBON TETRACHLORIDE, CHLORINATED CLEANING SOLVENTS, AMMONIA AND HOUSEHOLD DETERGENTS THAT CONTAIN AMMONIA.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com CARBON BRUSHES To maintain maximum efficiency of the motor, we recommend changing the carbon brushes every 60 hours of operation. To inspect or replace the carbon brushes: 1. Unscrew and remove the motor cover on the right. 2. Carefully take out the two carbon brushes using pliers and replace with new brushes. 3. Replace the motor cover and secure with the screws. LUBRICATION Your tool has been correctly lubricated and is ready to use. It is recommended the gears be regreased with a gear lubricant at every carbon brush change. BEARINGS Bearings that become noisy (due to heavy load or abrasive material damage) must be replaced by a qualified technician as soon as possible to avoid overheating or motor failure.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DRIVE BELT Inspect the drive belt every 60 hours of use. If the drive belt shows signs of drying out, cracking, tearing or improper tracking, it must be replaced. To replace the drive belt, 1. Unscrew and remove the belt cover on the left. 2. Replace with an identical replacement belt and replace the drive belt cover. SPECIFICATIONS Model CEP720B Voltage 230V~ 50Hz Rated Input Power 720W Maximum Depth of Cut 3 mm P l a n i n g W i d t h ( W i d t h o f C u t ) 8 2 m m Rebating Depth 18 mm Dust Extraction Diameter Inner - 35 mm / Outer - 42 mm Duty Cycle S1 (continuous) Weight 3.2 kg Dimensions 290 x 165 x 170 mm Sound Pressure 84 dB LpA Guaranteed Sound Power 95 dB LWA Uncertainty Factor (K) 3 dB Vibration (Main handle) 6.197 m/s Uncertainty Factor (K) 1.5 m/s2
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OTHER TOOLS IN THE CURRENT CLARKE RANGE Replacement Blades- CEP720RB Palm Sander - CPS125 Power File - CPF13 Length: 80mm Depth: 5.5mm Thickness: 1.2mm Part No. 6462042 Powerful 125W motor No load speed: 13500rpm Part No. 6462061 400w, 230v motor Variable speed: 300 - 1700 m/min Part No. 6462062 Rotary Tool Kit - CRT130 Router - CR1200 Belt Sander - BS1 Variable Speed: 13000 - 31600rpm 40 piece accessory kit Part No. 6462000 1200w, 230v motor Max plunge depth: 55mm Part No.6462083 900w, 230v motor. Belt size:76 x 533mm No load speed: 380m/min Part No. 6462050
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - UKCA
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - CE