TPS_CPCI-A-3U-200C MURATA | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
www.murata-ps.com cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ cPCI-A-3U-200C.A01 Page 1 of 4
FEATURES
/square6 /square6 /square6 /square6 /square6 /square6 /square6 /square6 /square6 /square6
DESCRIPTION
The cPCI-A-3U-200C is a high-reliability, 200W, continu- ous power, 3Ux8HP CompactPCI™ power supply devel- oped for chassis’ with airflows as low as 250lfm. The use of 2 converters operating in parallel for the 3.3V and the 5V outputs enables maximum current draw on the two outputs simultaneously. Compliant with the PICMG 2.11 standard. With a widerange input of 90-264VAC, safety agency approvals to UL60950 and EN60950, EMI compliance to Class B FCC and EN55022 standards, the cPCI-A- 3U-300C was designed with globally-deployed systems in mind. Additional features include remote sense com- pensation, unit enable control (EN#), output inhibit control (INH#), output fault signal (FAL#), and thermal warning signal (DEG#). LEDs are provided for visual indication of input power presence and output fault condition. 3Ux8HP package 200W power at -5 to 55ºC PICMG 2.11 Compliant Widerange 90-264VAC Input Active power factor correction to EN61000-3-2 Class B conducted EMI performance 47-pin I/O Connector 80% efficiency Full power with just 250lfm airflow Hot-swap capable INPUT CHARACTERISTICS Parameter Conditions Min Typ Max Units Input Operating Voltage Auto range, single phase 90 264 Vac Input Frequency 47 63 Hz Input Current 230Vac 3.5 A rms Power Factor 230Vac and 115Vac, full load 0.98 Inrush Current 230Vac 50 A pk OUTPUT CHARACTERISTICS Output Nominal Voltage Output Current Load Regulation1 Min Max V11 +5.0Vdc 0A 25A ±1% V21 +3.3Vdc 0A 36A ±1% V31 +12Vdc 0A 5A ±4% V41 -12Vdc 0A 0.5A ±4% Parameter Conditions Min Typ Max Units Line Regulation All outputs 0.5 % PARD (V1 & V2) 4 20MHz bandwidth 75 mV p-p PARD (V3 & V4)4 20MHz bandwidth 120 mV p-p Hold-up Time 220Vac, full load 14 msec Turn-on Delay 2 sec Rise Time 10% to 90% of full value 30 msec Transient Response ΔV, 50% load step ±5 %V nom Settling time 500 μsec Over-Voltage and Short Circuit Protection5 V1, V2, & V3: Latching 110 130 %V nom Remote Sense Compensation2 V1, V2 200 mV Current Share Tolerance3 V1, V2 ±10 % Isolation Pri-Sec 3 kVac Pri-Chassis 1.5 kVac Sec-Chassis 100 Vdc Notes: 1. Maximum combined power any combination of outputs is 200W 2. Maximum voltage compensation for cable losses . 3. Tolerance applicable up to 6 parallel units. Single wire current share on V1 & V2 for 50% to 100% load. 4. Measured across 1μF ceramic capacitor and 120μF electrolytic capacitor. 5. Automatic recovery upon removal of overload condition. SELECTION GUIDE Model Number Power Output Current1 5V 3.3V 12V -12V CPCI-A-3U-200C 200W 25A 36A 5A 0.5A Yes Yes Ḥ For full details go to www.murata-ps.com/rohs
www.murata-ps.com cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ cPCI-A-3U-200C.A01 Page 2 of 4 STATUS & CONTROL SIGNALS & INDICATORS Name Description Enable (EN#) Contact closure to external ground to start unit. On shortest pin (last make, first break). Output Inhibit (INH#) TTL –compatible signal inhibited with GND or TTL “0”. Output Fault (FAL#) TTL compatible signal ,open collector active low signal .Indicates one or more outputs below 90% of specifie d rate. Remote Sense (RS+, RS-) Available on V1 & V2. Maximum voltage compensation for cable losses 200mV. Thermal Warning (DEG#) Open collector active low 10ºC before power supply shut down. Front Panel Power Indicator LED A single bi-color indicator LED Green LED - indicates output in range Red LED - indicates one or more outputs below 90% of specified range. GENERAL CHARACTERISTICS Parameter Conditions Min Typ Max Units Efficiency 230Vac, full load 80 % 120Vac, full load 76 Switching Frequency Main Converter 68 kHz MTBF Calculated per Bellcore standard B332 Gb 30ºC 300 khrs Weight Unpackaged 800 g PROTECTION Parameter Conditions/Response Inception Units Min Typ Max Inrush Current Limit 230VAC 50 A rms Input Protection Internal line fuse 6.3 A rms Over-voltage Protection V1, V2, & V3 with latched shutdown 110 130 %V nom Parameter Conditions/Response Output Overload Protection Outputs are individually protected against overloads and indefinite short circuit with automatic recov ery upon removal of the fault condition. Hot-Swap Capability Protected by internal ORing diodes Output Fault Isolation Output isolation devices are present in all outputs to isolate faults within a failed power supply. Thermal Shutdown Automatic recovery upon restoration to operational temperatures ENVIRONMENTAL CHARACTERISTICS Parameter Conditions Min Typ Max Units Ambient Operating Temperature Full load with 250LFM forced air and derating linearly above 55°C to 70°C, by 2.5% per °C -5 55 ºC Ambient Storage Temperature -40 85 ºC Operating Humidity Non-condensing 95 % Storage Humidity Non-condensing 95 % Altitude Operating 6000 ft Storage 40000 ft
www.murata-ps.com cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ cPCI-A-3U-200C.A01 Page 3 of 4 ELECTROMAGNETIC COMPATIBILITY (EMC) Characteristic Compliance Input Current Harmonics EN61000-3-2 Conducted Emissions EN55022/CISPR22, Class B, with external TBD line filter Electrostatic Discharge (ESD) EN61000-4-2, Level 4, 8kV air Radiated Immunity EN61000-4-3, Level 3, 10V/m Conducted Immunity EN61000-4-4, Level 3, ±2kV Line Voltage Surge EN61000-4-5, Level 3, line-to-line 1kV line to chassis 2kV Conducted Disturbance EN61000-4-6, Level 2, 3Vrms Power Frequency Magnetic Field EN61000-4-8, 3A/m Line Voltage Interruptions EN61000-4-11 SAFETY AGENCY RATINGS Input Voltage 100-240Vac Input Current 3.5A MECHANICAL DIMENSIONS CERTIFICATIONS Agency/Characteristic PENDING Standard UL UL60950-1 CSA CSA C22.2-234, Level 3 (per cUL) CE EN-60950, Class 1, SELV CE-Mark RoHS EN Directive 2002/95/EC; self-certified 169.60 FORCED COOLING AIR 94.00 1.60 6.43 2.50 100.00 128.60 17.63 40.34 CL 3.10 POWER
www.murata-ps.com cPCI-A-3U-200C Series 200W 3Ux8HP AC/DC CompactPCI™ cPCI-A-3U-200C.A01 Page 4 of 4 10/24/08 Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2008 Murata Power Solutions, Inc. USA: Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Canada: Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com UK: Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com France: Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com Germany: München, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com Japan: Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com China: Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com Singapore: Parkway Centre, Tel: +65 6348 9096, email: singapore@murata-ps.com Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356 www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED RoHS COMPLIANCE INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300ºC for 10 seconds. The pin termination finish on this product series is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs CONNECTOR Pin Pin Type Signal Name 1-4 Normal V1 V1 Output 5-12 Normal RTN V1 and V2 Return 13-18 Normal V2 V2 Output