CP3-SVE-M120DC-WV

CP3-SVE-M120DC-WV KONTRON | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 7

Technical content

120 Watt DC/DC for Industry and Railways

 Wide input range 14.4 to 154 VDC  Five outputs for CPCI  Extended temperature, fanless  Redundant operation CP3-SVE-M120DC-WV Universal DC power supply for CompactPCI

Universal DC power supply for CompactPCI The product description provided with this data sheet is regarded as part of the general Kontron CPCI Power Supply manual ID 24139. For further information, in particular general details as well as disclaimer, safety and warranty statements, refer to the CPCI Power Supply Manual. This power supply is designed for use within standard CompactPCI systems for Industrial and Railway installations. It is as well suited for integration in electronic or electrical enclosures, e.g. Kontron’s 19” racks. // 2 www.kontron.com Dimensions are in mm. Values according to ISO 2768-1 m. Exeptions: values in brackets (nn) with tolerances +/- 0.5 TECHNICAL INFORMATIONˆ FORM FACTOR 3U DIMENSIONS 166.5 x 30.1 x 107 mm, 6HP WEIGHT 600 g MECHANICS 19” rack POWER SUPPLY CONNECTOR DIN M24/8 connector COATING Lackwerke Peters ELPEGUARD SL 1307-FLZ/2 COOLING Convection cooling MTBF tbd. MECHANICAL DRAWINGˆ

// 3 www.kontron.com For T amb = 25 °C, Vin nom, Iout nom, unless otherwise specified ELECTRICAL SPECIFICATIONS ˆ INPUT INPUT VOLTAGE NOMINAL 24, 36, 48, 72, 96, 110 VDC INPUT VOLTAGE OPERATING 16.8 – 137.5 VDC INPUT VOLTAGE RANGE 14.4 – 154 VDC (t<=1.0 sec) STANDBY INPUT POWER Max. 3 W SWITCHING FREQUENCY Typical 100 / 375 kHz (Converter/Step-down Vout 1 ) OUTPUT OUTPUT VOLTAGES 5 V (adjusted to 5.1 V), 3.3 V (adjusted to 3.4 V), 12 V, -12 V, 5 V stby INITIAL SET ACCURACY ±0.5 % (Vout 1,2,3), ±2 % (Vout 4,5) no load MINIMUM LOAD No minimum load required SHORT CIRCUIT Continuous short circuit proof RIPPLE & NOISE Output 1,2,3: <2 % pk-pk. 20 MHz bandwidth Output 4,5: <4 % pk-pk, 20 MHz bandwidth START TIME < 0.9 s MAX. OUTPUT CAPACITANCE 10.000 µF (Vout 1,2,3), 500 µF/A (Vout 4,5) TEMPERATURE COEFFICIENT < 0.01 %/°C (Vout 1,2,3), 0.03 %/°C (Vout 4,5) INPUT UNIT INPUT VOLTAGE NOMINAL V 24 36 46 72 96 110 UNDER VOLTAGE TURN-ON V < 15.0 … 16.5 depends on position of the rotating switch S101 UNDER VOLTAGE TURN-OFF IF POSITION OF S101 IS SET TO V 12 … 14 20 … 21 25 … 28 40 … 42 52 … 56 60 … 64 UNDER VOLTAGE TURN-OFF V 12.0 … 14 in all other positions of the rotating switch S101 INPUT CURRENT DISABLED MODE* INERTIAL FUSE A 16 T *Enable signal open or Inhibit signal low OUTPUT UNIT OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 OUTPUT 5 OUTPUT VOLTAGE NOMINAL V 5.0* 3.3* 12 -12 5 OUTPUT CURRENT NOMINAL A 20 14 10 0.5 0.5** OUTPUT POWER W 100 47 120 6 2.5 OUTPUT POWER MAX. W 120 for Output 3 only; 100 for loading Output 1 or Output 2 with more than 20 % EFFICIENCY @ FULL LOAD OUT 1 % 86 EFFICIENCY @ FULL LOAD OUT 3 % 91 SHORT CIRCUIT CURRENT (TYPICAL) A 44A (pulse) 22A (pulse) 30A (pulse) 1.3A (cont.) 2A (cont.) TRANSIENT RESPONSE 25 %/75 % LOAD STEP mV ± 100 ± 100 ± 200 ± 200 ± 100 *3.3 V adjusted to 3.4 V and 5.0 V adjusted to 5.1 V **for <10 sec, maximum continuous current is 0.3 A

// 4 www.kontron.com ELECTRICAL SPECIFICATIONˆ REGULATION LINE REGULATION < 0.5 % LOAD REGULATION < 1 % (Vout 1,3), <3 % (Vout 2,4,5) at 0 % - 100 % load Value could be higher, depending on the voltage drop of the connector RIPPLE & NOISE Output 1,2,3: <2 % pk-pk. 20 MHz bandwidth Output 4,5: <4 % pk-pk, 20 MHz bandwidth PROTECTION AND CONTROL OVERVOLTAGE PROTECTION 110 … 120 % for Vout 1, 2, 3, 4 OVERCURRENT PROTECTION If Vout1 is shut down due to overload, Vout2 will be switched-off, too OVER TEMPERATURE WARNING DEG = low at +105 °C … 110 °C PCB-temperature with 5 °C hysteresis and auto recovery OVER TEMPERATURE PROTECTION Shutdown at +110 °C … 115 °C PCB-temperature with 5 °C hysteresis and auto recovery ACTIVE REVERSE POLARITY PROTECTION Max. 160 V ACTIVE INRUSH CURRENT LIMITATION Max. 15 A (at t>100 µs) 0.4 A²sec INPUT VOLTAGE DETECTION With the rotating switch S101 the undervoltage levels can be set. See INPUT table. HOLD-UP-TIME >10 ms at full load GREEN LED Blinking indicates: - Vin is lower than adjusted under voltage turn-off value - One of the output voltages 1-4 is not in specified range - Converter is in standby mode Lightning indicates: - Converter is in normal operating mode ENABLE SIGNAL Inputs INH Low Low High High EN Low High Low High Reference to GND Low level: 0 V … 0.8 V, High level: 8 V … 9 V or open The pin sources about 170 µA at low level INHIBIT SIGNAL OFF: INH connected to GND; see table above SUPPLY FAIL SIGNAL Open-collector output, emitter grounded (npn-transistor). Active level: low. Max current 20 mA, Max voltage 9 V, saturation voltage <0.5 V. FAL switches LOW, if one of the outputs 1-4 is out of tolerance of ±10 % or if Vin breaks down. If Vin breaks down, it remains 5ms between the edge of the FAL-Signal and the break down of Vout. DERATING SIGNAL Open-collector output, emitter grounded (npn-transistor). Active level: low. Max current 20 mA, Max voltage 9 V, saturation voltage <0.5 V SENSE +/- Sense connection not required. If accomplished, the voltage at the load is reduced by 100 mV, to provide compensation of voltage drops (max. 0.2 V each line) at Vout1 and Vout2 between power supply and load. The pins Sense return, Sense +5 V and Sens +3.3 V must be connected with the load. The sense signal should not be longer than 0.4m. STANDBY VOLTAGE 5 V/0.5 A (for 10 sec, 0.3 A continuous) REDUNDANT OPERATION Only for outputs 3,4,5, with one additional converter. The wires should be as short as possible.

// 5 www.kontron.com DIN M24/8 POWER SUPPLY CONNECTOR The V1 ... V5 output voltages from the power supply unit to the back- plane are connected via a 32-pole DIN 24/8 male power supply connector. For the pinouts of the DIN M24/8 power supply connector please refer to the following table. ATTENTION! The DC INPUT has changed to different pins, comparred to previ- ous Kontron DC power supplies.Respective rework of target systems is necessary. // Orientation of the DIN M24/8 Power Supply Connector PIN FUNCTION PIN FUNCTION 2 NC Not connected B.17 V out2 +3.3 V Output Voltage 5 NC Not connected B.18 V out2 +3.3 V Output Voltage 8 NC Not connected B.19 V out3 +12 V Output Voltage 11 Case/PE Chassis Ground B.20 V out4 -12V Output Voltage A.13 V out5 +5 V aux C.13 EN Enable Signal A.14 INH Inhibit Signal C.14 DEG Derate Signal A.15 NC Not connected C.15 FAL Supply Fail Signal A.16 S return Sense return C.16 V out2 +3.3 V Output Voltage A.17 S+5 V Sense V out1 C.17 V out2 +3.3 V Output Voltage A.18 S+3.3 V Sense V out2 C.18 V out2 +3.3 V Output Voltage A.19 V out3 +12 V Output Voltage C.19 V out3 +12 V Output Voltage A.20 V out4 -12 V Output Voltage C.20 V out4 -12V Output Voltage B.13 V out2 +3.3 V Output Voltage 22 V out1 +5 V Output Voltage B.14 V out2 +3.3 V Output Voltage 25 GND Ground B.15 V out2 +3.3 V Output Voltage 28 V in + +Input Voltage B.16 V out2 +3.3 V Output Voltage 31 V in - -Input Voltage

// 6 www.kontron.com ELECTRICAL SPECIFICATIONˆ EMC EMC STANDARD EN 50121-3-2:2015 EMISSIONS EN 55011:2009 + A1:2010, Class A* *In Built-in condition the devices may show different EMC properties ESD EN 61000-4-2:2009, level 3 (6kV/8kV), Criteria A BURST EN 61000-4-4:2012, level 3 (2kV), Criteria A SURGE EN 50121-3-2:2015, line to line ±1kV, 42R, and line to case ±2kV, 42R, Criteria A EN61000-4-5:2014, line to line ±0.5kV, and line to PE ±1kV Criteria A CONDUCTED IMMUNITY EN 61000-4-6:2014, level 3 (10V), Criteria A RADIATED IMMUNITY EN 61000-4-3:2006 + A1:2008 + A2:2010, 20V/m, Criteria A SAFETY ITE SAFETY EUROPE EN 62368-1 RAILWAY SAFETY EN 50155 Isolation: 2200 VDC Input/Output, 2200 VDC Input/PE, 710 VDC Output/PE ENVIRONMENT OPERATING TEMPERATURE -40 °C to + 85 °C Class TX: +85 °C max. 10 min. Derating >70 °C continuously STORAGE TEMPERATURE -40 °C to +85 °C VIBRATION / SHOCK / BUMP EN 61373:2010, Cat.1B FIRE & SMOKE tbd INSTALLATION The power supplies have to be installed according to the guidelines currently in force, like other open electronic component assem- blies. Plug in not under voltage. Attention must be paid to sufficient ventilation, carry off heat, fastening and protection against accidential contact. The pin 11 (case/PE) has to be properlyconnected in order to assure operation. ATTENTION! At Pout max (for time > 1 min) a warming up of the front plate up to 15 °C over the ambient temperature is possible. FAULT PROTECTION The power supplies are equipped with a soldered in-time-lag fuse corresponding to IEC 60127-2 for input protection. In case of fault, the supplying current source must be capable to blow the fuse. In some applications 2 fuses would be necessary, one in each input line.

// 7 ˆGLOBAL HEADQUARTERS Kontron Europe GmbH Gutenbergstraße 2

85737 Ismaning, Germany

T el.: + 49 821 4086-0 Fax: + 49 821 4086-111 info@kontron.com www.kontron.com Copyright © 2021 Kontron. All rights reserved. All data is for information purposes only and not guaranteed for legal purposes. Information has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Kontron and the Kontron logo and all other trademarks or registered trademarks are the property of their respective owners and are recognized. Specifications are subject to change without notice. CP3-SVE-M120DC-WV-20210305 - WMH

ORDERING INFORMATION

BLOCK DIAGRAMˆ ˆ ARTICLE DESCRIPTION CP3-SVE-M120DC-WV-E1X CompactPCI DC wide voltage Power Supply 3U/6HP, 120 W. Input voltage nominal 24,36,48,72,96,110 V. Output +3.3 V/14 A, +5 V/20 A, +12 V/10 A, -12 V/0.5 A. M-Connector to backplane, LED, EN50155 compatible, fanless operation, redundant, extended temperature range -40 °C to +70 °C, +85 °C max. 10 minutes (Class TX)