7610193 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 12
Technical content
OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS DL0423 - ISS 4 HYDRAULIC MOTORCYCLE LIFT MODEL NO: CML5 PART NO: 7610193
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE hydraulic motorcycle lift. Before attempting to operate this product, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you can look forward to the product giving you long and satisfactory service. GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended. Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission. This guarantee does not effect your statutory rights. SPECIFICATIONS Model Number CML5 Maximum Load 680 kg Minimum Table Height 135 mm Maximum Table Height 430 mm Overall Length (inc handle) 1200 mm Overall Width 390 mm Weight 37.5 kg
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SAFETY PRECAUTIONS 1. ALWA YS work in accordance with the instruction handbook. 2. NEVER exceed the maximum safe working load of 680 kg, and only use the motorcycle lift for its intended purpose. 3. NEVER use the lift if it has been subjected to an abnormal load or shock. It should be removed from service immediately and fully inspected by qualified personnel, and passed as serviceable, before being used again. 4. NEVER rely upon the hydraulic ram to support the saddle when loaded. Always use the locking bar to hold the saddle in one of the positions provided. 5. ALWA YS use the lift on a solid, flat, level surface. 6. ALWAYS screw down the stabilisers before putting the saddle under load. NOTE: The castors are not designed to take the weight of the motorcycle, but are used merely to move the lift quickly and easily around the workshop. On no account must you raise a loaded platform unless the stabilisers are screwed down, and NEVER use the lift to transport a load. 7. ALWA YS use appropriate safety equipment, such as protective footwear, when using this lift. 8. ALWAYS inspect the lift before use to ensure it is in good condition, and replace any damaged or worn parts. 9. ALWA YS use spare parts supplied by Clarke International. Using non- standard parts could be extremely dangerous. 10. ENSURE the operator is trained in both operational and safety aspects. 11. NEVER leave this lift unattended whilst there is a load on it. 12. NEVER allow children or bystanders anywhere near this lift whilst it is in use. 13. NEVER use this lift to lift people or animals. UNPACKING Check to ensure that no damage has occurred during transit. Any damage should be reported to your Clarke dealer immediately. The following should be included: 1 x Main frame assembly 1 x Lifting pedal 1 x T - Handle assembly and retaining pin 1 x Locking bar handle 1 x Hydraulic pump assy c/w lowering pedal 1 x Pair of ratchet straps
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OVERVIEW ASSEMBLY THE RAM ASSEMBLY 1. Secure the ram assembly to its baseplate using the two M8x25 bolts and M8 Spring washers supplied. 2. Tighten the bolts securely.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com THE LOCKING BAR 1. Locate the locking bar handle in to the socket at each side of the lift. 2. Place a M8 spring washer on to the threads and screw on the M8 nut securely.
- Ensure the locking bar is free to rotate under its own weight. The locking bar should hinge so that the ends engage against one of the ridges on the base. THE RAM TO THE FRAME 1. Lift the saddle manually and hook the ram frame over the ram as shown. 2. Secure in place using the locking screw.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com THE HANDLE AND OPERATING PEDAL The handle is secured to the frame using the pin provided. The operating pedal should be slid into place and secured using the M8x12 bolt supplied. OPERATION NOTE: The operator must be able to watch the lift and the load during all movements. RAISING THE LOAD 1. Position the saddle between the wheels of the motorcycle, as near to the centre of gravity as possible. 2. Pump the operating pedal until the saddle makes light contact with the motorcycle frame, then assess where packing may be required to ensure the motorcycle is well supported and stable.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 3. When the motorcycle is satisfactorily supported and completely stable, screw down the two stabilisers. T h i s r e d u c e s a n y l o a d f r o m t h e castors. 4. Raise the load slowly by pumping the operating pedal. 5. At all times make sure that the motor cycle is fully supported and stable. 6. Once you have reached the desired height, ensure the locking bar is engaged with the notches on the base. 7. Press the release pedal gently, allowing the saddle to lower until the load is taken by the locking bar. Do not work under the raised load until it is secured using the locking bar. 8. Secure the load using the supplied ratchet straps before you begin work. WARNING: UNDER NO CIRCUMSTANCES MUST YOU RELY UPON THE RAM TO SUPPORT THE LOAD. WARNING: ENSURE THE MOTORCYCLE IS FULLY STABILISED BEFORE COMMENCING WORK.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com LOWERING THE LOAD 1. Pump the operating pedal to raise the load slightly and release the locking bar. 2. Push the locking bar against the ram and into the locking bar retaining clip. 3. Press down on the release pedal and allow the load to descend. 4. Remove the locking bar from the locking bar retaining clip before using the lift again. MAINTENANCE BEFORE EACH USE Visually inspect the lift for distortion of parts, cracked welds, damaged wheels or castors, oil leakage from the ram, or any other sign of damage. Should any of these be found, do not use the lift, and have it inspected and repaired by a qualified technician before putting back into use. If necessary, consult your Clarke dealer. If any warning labels becomes illegible, have it replaced. Contact your Clarke dealer. REPAIR Should any repairs be required they should be carried out by qualified service engineers, contact the Clarke Service department on 020 8988 7400. WARNING: TAKE GREAT CARE WHEN LOWERING. YOU ONLY NEED TO PRESS THE RELEASE PEDAL VERY LIGHTLY. TOO HEAVY A TOUCH WILL RESULT IN THE LOAD DESCENDING TOO RAPIDLY WHICH COULD BE HAZARDOUS
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com PARTS LIST MAIN UNIT HARDWARE BOX ITEM NO DESCRIPTION PART NUMBER ITEM NO DESCRIPTION PART NUMBER A Base HTCML5A L Pump Spring HTCML5L B Link HTCML5B M Lock Rear Castor Assy HTCML5M C Lift Saddle HTCML5C N He ight Lock Bar HTCML5N D Height Lock Release HTCML5D O F ront Wheel Assembly HTCML5O E Connecting Rod HTCML5E P Loops HTCML5P F T - Handle HTCML5F Q Clip HTCML5Q G Locking Screw HTCML5G R Height Lock Springs HTCML5R H Return Spring HTCML5H S Lock Position Ridge HTCML5S I Hydraulic Ram HTCML5I T Rubber Pads HTCML5T J Foot Pedal HTCML5J U Oil Fill Plug HTCML5U K Release Pedal HTCML5K
1 Spring Nut
3 Cotter Pin
8 Ratchet Straps
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com PART DIAGRAM
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY