CH7105B CHRONTEL | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 7
Technical content
209-1000-133 Rev 1.5 2021-5-20 1 Chrontel CH7105B HDMI to SDTV/VGA Converter FEATURES GENERAL DESCRIPTION HDMI Receiver compliant with HDMI 1.4 specifications Support multiple output formats: — SDTV format (CVBS or S-Video output, NTSC and PAL) — Analog RGB output for VGA with Triple 9-bit DAC up to 200MHz pixel rate. Sync signals can be provided in separated or composite manner. Support VESA and CEA timing standards up to UXGA and 1920x1080@60Hz On-chip Audio encoder which support 2 channel IIS/ S/PDIF audio output VGA output is compliant with VESA VSIS v1r2 specification MCU embedded to handle the control logic Support device boot up by automatically loading firmware from on-chip flash Integrated EDID Buffer TV/VGA connection detection supported HDMI input detection supported Scaler engine integrated for 640x480 safe mode input supported in SDTV output application Support Auto Power Saving mode and low stand-by current Support RGB to YCC conversion in ITU-R BT.601 and 709 color space IIC slave interface and HDMI DDC interface are available for debug and firmware update. Low power architecture RoHS compliant and Halogen free package Offered in 40-Pin QFN package (5 x 5 mm) APPLICATION Car Infotainment Device HDMI to VGA/SDTV Adapter/Docking Station Notebook/Ultrabook IPC Handheld/Portable Device Digital Video Systems Chrontel’s CH7105B is a low -cost, low -power semiconductor device that consists of HDMI receiver, three separate 9 -bit video Digital -to-Analog Converters (DACs), SDTV encoder and audio encoder , which can convert HDMI signals into CVB S/S-Video/VGA outputs with IIS or SPDIF audio output. The HDMI Receiver integrated is compliant with HDMI 1.4b. With sophisticated MCU and the on-chip flash , CH7105B supports auto-boot and EDID buffer. Take the advantage of Firmware auto loaded from the embedded flash, CH7105B can support HDMI input detection, DAC connection detection and determine to enter into SDTV mode or VGA mode or Power saving mode automatically.
2 209-1000-133 Rev 1.5 2021-5-20 IIS/SPDIF CVBS/ S-Video/ VGA DDC HPD TMDS HPD Generator HDMI 1.4 RX Sync Generator CSC Video FIFO Audio FIFO Audio Encoder VGA Encoder SDTV Encoder MCU & EDID Buffer On Chip Flash SPC/SPD GPIOs DDC Equalizer Figure 1: CH7105B Functional Block Diagram
209-1000-133 Rev 1.5 2021-5-20 3
1.0 PIN-OUT
1.1 Package Diagram
DDC_SCL DDC_SDA MCLK RB DVDD DGND SD/SPDIF WS SCLK SPD0 GPIO0 GPIO1 VO VGA_SCL HO/CSYNC DVDD DGND SPC0 AVCC VGA_SDA DAC0 AVCC_DAC XO RBIAS DAC2 DAC1 AVCC_DAC XI HPD RD2P RD2N RD1N AVDD AVCC RD0P RCP RCN RD0N RD1P Figure 2:CH7105B 40-Pin QFN Pin Out
4 209-1000-133 Rev 1.5 2021-5-20
1.2 Pin Description
Table 1: Pin Name Descriptions Pin # Type Symbol Description
4 In DDC_SCL Serial Port Clock to HDMI/DVI Transmitter
This pin functions as the clock bus of the serial port to HDMI or DVI DDC transmitter. This pin require s a pull -up 47 kΩ resistor to the desired voltage level.
5 In/out DDC_SDA Serial Port Data to HDMI/DVI Transmitter
This pin functions as the data bus of the serial port to HDMI or DVI DDC transmitter. This pin require s a pull -up 47 kΩ resistor to the desired voltage level.
6 Out SD/SPDIF I2S Serial Data or SPDIF Output
7 Out WS I2S Word Select
8 Out SCLK I2S Continuous Serial Clock
9 Out MCLK I2S System Clock
10 In RB Chip Reset
Low to 0V for reset. Typical High level is 3.3V
12 In SPC0 Serial Port Clock Input
This pin functions as the clock pin of the serial port. External pull -up
6.8 K resister is required
13 In/out SPD0 Serial Port Data Input / Output
This pin functions as the bi -directional data pin of the serial port. External pull-up 6.8 K resister is required 14,15 In/Out GPIO General Purpose Input/Output
16 Out VO Vertical Sync Signal Output
The amplitude of this pin is from 0 to AVCC
17 Out HO/CSYNC Horizontal Sync Signal Output
The amplitude of this pin is from 0 to AVCC It also functions as a Composite sync output
20 Out VGA_SCL Serial Port Clock Output to VGA Receiver
The pin should be connected to clock signal of VGA DDC. This pin requires a pull-up 10 kΩ resistor to the desired voltage level
21 In/Out VGA_SDA Serial Port Data to VGA Receiver
The pin should be connected to data signal of VGA DDC. This pin requires a pull-up 10 kΩ resistor to the desired voltage level
22 In XI Crystal Input
A parallel resonance crystal should be attached between this pin and XO.
23 Out XO Crystal Output
A parallel resonance crystal should be attached between this pin and XI. If an external CMOS clock is injected to XI, XO should be left open.
25 Out DAC0 VGA Blue Component/S-Video C Component output
26 Out DAC1 VGA Green Component/ S-Video Y Component output
28 Out DAC2 VGA Red Component/ CVBS output
29 In RBIAS Current Set Resistor Input
This pin sets the DAC current. A 10 K, 1% tolerance resistor should be connected between this pin and AVSS using short and wide traces
30 Out HPD HDMI Receiver Hot Plug output
31,32,33, 34,36,37, In RD[2:0]P/N RCP/N HDMI TMDS Input HDMI differential clock and data input pairs
209-1000-133 Rev 1.5 2021-5-20 5 39,40 1 Power VDDPLL PLL Power Supply (1.2V) 2,18 Power DVDD Digital IO Power Supply (1.2V) 3,19 Power DGND Digital Ground 11,38 Power AVCC Analog Power Supply (3.3V) 24,27 Power AVCC_DAC Analog DAC Power Supply (3.3V) 35 Power AVDD HDMI Receiver Analog Power Supply (1.2V) Pad Power GND Power Supply Ground
6 209-1000-133 Rev 1.5 2021-5-20
2.0 PACKAGE DIMENSION
Figure 3: 40 Pin QFN Package Table 2: Table of Dimensions No. of Leads SYMBOL 40 (5 X 5 mm) A B C D E F G H I Milli- meters Notes: 1. Conforms to JEDEC standard JESD-30 MO-220.
209-1000-133 Rev 1.5 2021-5-20 7 Disclaimer This document provides technical information for the user. Chrontel reserves the right to make changes at any tim e without notice to improve and supply the best possible product and is not responsible and does not assume any liability for misapplication or use outside the limits specified in this document. CHRONTEL warrants each part to be free from defects in material and workmanship for a period of one (1) year from date of shipment. Chrontel assumes no liability for errors contained within this document . The customer should make sure that they have the most recent data sheet version. Customers should take appro priate action to ensure their use of the products does not infringe upon any patents. Chrontel, Inc. respects valid patent rights of third parties and does not infringe upon or assist others to infringe upon such rights. Chrontel PRODUCTS ARE NOT AUTHORI ZED FOR AND SHOULD NOT BE USED WITHIN LIFE SUPPORT SYSTEMS OR NUCLEAR FACILITY APPLICATIONS WITHOUT THE SPECIFIC WRITTEN CONSENT OF Chrontel. Life support systems are those intended to support or sustain life and whose failure to perform when used as directed can reasonably expect to result in personal injury or death.
ORDERING INFORMATION
Part Number Package Type Content Protection Operating Temperature Range Minimum Order Quantity CH7105B-BF 40 QFN, Lead-free None Commercial : 0 to 70C 490/Tray CH7105B-BFK 40 QFN, Lead-free HDCP 1.4 Commercial : 0 to 70C 490/Tray CH7105B-BFI 40 QFN, Lead-free None Industrial : -40 to 85C 490/Tray CH7105B-BFIK 40 QFN, Lead-free HDCP 1.4 Industrial : -40 to 85C 490/Tray Chrontel www.chrontel.com E-mail: sales@chrontel.com 2021 Chrontel - All Rights Reserved.