CS2000-CP CIRRUS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 36
Technical content
Features
Delta-Sigma Fractional-N Frequency Synthesis – Generates a Low Jitter 6 - 75 MHz Clock from an 8 - 75 MHz Reference Clock Clock Multiplier / Jitter Reduction – Generates a Low Jitter 6 - 75 MHz Clock from a Jittery or Intermittent 50 Hz to
30 MHz Clock Source
Highly Accurate PLL Multiplication Factor – Maximum Error Less Than 1 PPM in High- Resolution Mode I²C® / SPI™ Control Port Configurable Auxiliary Output Flexible Sourcing of Reference Clock – External Oscillator or Clock Source – Supports Inexpensive Local Crystal Minimal Board Space Required – No External Analog Loop-filter Components General Description The CS2000-CP is an extremely versatile system clocking device that utilizes a programmable phase lock loop. The CS2000-CP is based on a hybrid ana- log-digital PLL architecture comprised of a unique combination of a Delta-Sigma Fractional-N Frequency Synthesizer and a Digital PLL. This architecture allows for both frequency synthesis/clock generation from a stable reference clock as well as generation of a low- jitter clock relative to an external noisy synchronization clock. The design is also unique in that it can generate low-jitter clocks relative to noisy external synchroniza- tion clocks at frequencies as low as 50 Hz. The CS2000-CP supports both I²C and SPI for full software control. The CS2000-CP is available in a 10-pin MSOP pack- age in Commercial (-10°C to +70°C) grade. Customer development kits are also available for device evalua- tion. Please see “Ordering Information” on page 35 for complete details. I²C / SPI Auxiliary Output 6 to 75 MHz PLL Output 3.3 V I²C/SPI Software Control
8 MHz to 75 MHz
Digital PLL & Fractional N Logic Output to Input Clock Ratio N Timing Reference PLL Output Lock Indicator
50 Hz to 30 MHz
JUN '08 DS761PP1 CS2000-CP
2 DS761PP1
4 DS761PP1
- PIN DESCRIPTION Pin Name # Pin Description VD 1 Digital Power (Input) - Positive power supply for the digital and analog sections. GND 2 Ground (Input) - Ground reference. CLK_OUT 3 PLL Clock Output (Output) - PLL clock output. AUX_OUT 4 Auxiliary Output (Output) - This pin outputs a buffered version of one of the input or output clocks, or a status signal, depending on register configuration. CLK_IN 5 Frequency Reference Clock Input (Input) - Clock input for the Digital PLL frequency reference. XTO XTI/REF_CLK Crystal Connections (XTI/XTO) / Timing Reference Clock Input (REF_CLK) (Input/Output) - XTI/XTO are I/O pins for an external crystal which may be used to generate the low-jitter PLL input clock. REF_CLK is an input for an externally generated low-jitter reference clock. AD0/CS 8 Address Bit 0 (I²C) / Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I²C Mode. CS is the chip select signal in SPI Mode. SCL/CCLK 9 Control Port Clock (Input) - SCL/CCLK is the serial clock for the serial control port in I²C and SPI mode. SDA/CDIN 10 Serial Control Data (Input/Output) - SDA is the data I/O line in I²C Mode. CDIN is the input data line for the control port interface in SPI Mode. 5 6 XTO CLK_OUT GND VD XTI/REF_CLK AD0/CS SCL/CCLK SDA/CDIN AUX_OUT CLK_IN
6 DS761PP1
- TYPICAL CONNEC TION DIAGRAM
Figure 1. Typical Connection Diagram
- CHARACTERISTICS AN D SPECIFICATIONS RECOMMENDED OPERATING CONDITIONS GND = 0 V; all voltages with respect to ground. (Note 1) Notes: 1. Device functional operation is guaranteed within thes e limits. Functionality is not guaranteed or implied outside of these limits. Operation outside of these limits may adversely affect device reliability. ABSOLUTE MAXIMUM RATINGS GND = 0 V; all voltages with respect to ground. WARNING: Operation at or beyond these limits may result in permanent damage to the device. Notes: 1. The maximum over/under voltage is limited by the input current except on the power supply pin. DC ELECTRICAL CHARACTERISTICS Test Conditions (unless otherwise specified): VD = 3.1 V to 3.5 V; TA = -10°C to +70°C (Commercial Grade). Notes: 2. To calculate the additional curr ent consumption due to loading (per output pin), multiply clock output frequency by load capacitance and power supply voltage. For example, fCLK_OUT (49.152 MHz) * C L (15 pF) * VD (3.3 V) = 2.4 mA of additional current due to these loading conditions on CLK_OUT. Parameters Symbol Min Typ Max Units DC Power Supply VD 3.1 3.3 3.5 V Ambient Operating Temperature (Power Applied) Commercial Grade T AC -10 - +70 °C Parameters Symb ol Min Max Units DC Power Supply VD -0.3 6.0 V Input Current I IN -± 1 0 m A Digital Input Voltage (Note 1)V IN -0.3 VD + 0.4 V Ambient Operating Temperature (Power Applied) T A -55 125 °C Storage Temperature T stg -65 150 °C Parameters Symbol Min Typ Max Units Power Supply Current - Unloaded ( Note 2)I D -1 2 1 8 m A Power Dissipation - Unloaded ( Note 2)P D -4 0 6 0 m W Input Leakage Current I IN -- ± 1 0 µ A Input Capacitance I C -8-p F High-Level Input Voltage V IH 70% - - VD Low-Level Input Voltage V IL -- 3 0 % V D High-Level Output Voltage (IOH = -1.2 mA) V OH 80% - - VD Low-Level Output Voltage (IOH = 1.2 mA) V OL -- 2 0 % V D
8 DS761PP1
AC ELECTRICAL CHARACTERISTICS Test Conditions (unless otherwise specified): VD = 3.1 V to 3.5 V; TA = -10°C to +70°C (Commercial Grade); CL =1 5p F . Notes: 3. 1 UI (unit interval) corresponds to t SYS_CLK or 1/fSYS_CLK. 4. t CS represents the time from the removal of CLK_IN by which CLK_IN must be re-applied to ensure that PLL_OUT continues while the PLL re-acquires lock. This timeout is based on the internal VCO frequen- cy, with the minimum timeout occurring at the maximum VCO frequency. Lower VCO frequencies will result in larger values of tCS. 5. Only valid in cloc k skipping mode; See “CLK_IN Skipping Mode” on page 14 for more information. 6. fCLK_OUT = 24.576 MHz; Sample size = 10,000 points; AuxOutSrc[1:0] = 11. 7. In accordance with AES-12id-2006 section 3.4.2. Measurements are Time Interval Error taken with 3rd order 100 Hz to 40 kHz bandpass filter. 8. In accordance with AES-12id-2006 section 3.4.1. Measurements are Time Interval Error taken with 3rd order 100 Hz Highpass filter. 9. 1 UI (unit interval) corresponds to t CLK_IN or 1/fCLK_IN. 10. The frequency accuracy of the PLL clock output is directly proportional to the frequency accuracy of the reference clock. Parameters Symbol Conditions Min Typ Max Units Crystal Frequency f XTAL Fundamental Mode 8 - 50 MHz Reference Clock Input Frequency f REF_CLK 8- 7 5 M H z Reference Clock Input Duty Cycle D REF_CLK 45 - 55 % Internal System Clock Frequency f SYS_CLK 8 18.75 MHz Clock Input Frequency (Auto R-Mod Disabled) f CLK_IN 50 Hz - 30 MHz Clock Input Frequency (Auto R-mod Enabled) f CLK_IN Auto R Modifier = 1 Auto R Modifier = 0.5 Auto R Modifier = 0.25 168 138 256 kHz kHz kHz Clock Input Pulse Width (Note 3)p w CLK_IN fCLK_IN < fSYS_CLK/96 fCLK_IN > fSYS_CLK/96 UI ns Clock Skipping Timeout t CS (Notes 4, 5)2 0 - - m s Clock Skipping Input Frequency f CLK_SKIP (Note 5) 50 Hz - 80 kHz PLL Clock Output Frequency f CLK_OUT 6- 7 5 M H z PLL Clock Output Duty Cycle t OD Measured at VD/2 48 50 52 % Clock Output Rise Time t OR 20% to 80% of VD - 1.7 3.0 ns Clock Output Fall Time t OF 80% to 20% of VD - 1.7 3.0 ns Period Jitter t JIT (Note 6) - 70 150 ps rms Base Band Jitter (100 Hz to 40 kHz) (Notes 6, 7) - 50 - ps rms Wide Band JItter (100 Hz Corner) (Notes 6, 8) - 175 - ps rms PLL Lock Time - CLK_IN (Note 9)t LC fCLK_IN < 200 kHz fCLK_IN > 200 kHz 100 200 UI ms PLL Lock Time - REF_CLK t LR fREF_CLK = 8 to 75 MHz - 1 2 ms Output Frequency Synthesis Resolution (Note 10)f err High Resolution High Multiplication ±0.5 ±112 ppm ppm
Inputs: Logic 0 = GND; Logic 1 = VD; CL =2 0p F . Notes: 11. Data must be held for sufficient ti me to bridge the transition time, tf, of SCL. Figure 2. Control Port Timing - I²C Format
10 DS761PP1
Inputs: Logic 0 = GND; Logic 1 = VD; CL =2 0p F . Notes: 12. tspi is only needed before first falling edge of CS after power is applied. tspi = 0 at all other times.
- Data must be held for sufficient time to bridge the transition time of CCLK.
Figure 3. Control Port Timing - SPI Format (Write Only)
4.1 Delta-Sigma Fractional- N Frequency Synthesizer
clock ratio is the value of N that is applied to the delta-sigma modulator (see Figure 4). clock should be stable and jitter-free. Figure 4. Delta-Sigma Fractional-N Frequency Synthesizer
4.2 Hybrid Analog-Digital Phase Locked Loop
to quickly achieve lock and then reduced for optimal jitter rejection.
12 DS761PP1
Figure 5. Hybrid Analog-Digital PLL
4.2.1 Fractional-N Source Selecti on for the Frequency Synthesizer
based on the presence of the Frequency Reference Clock or manually through register controls. Figure 6. Fractional-N Source Selection Overview
5.1 Timing Reference Clock Input
directly affects the performance of the PLL and hence the quality of the PLL output.
5.1.1 Internal Timing Reference Clock Divider
within the valid range as indicated in Figure 7. acteristics” on page 8 for more details.
5.1.2 Crystal Connections (XTI and XTO)
to the “AC Electrical Characteristics” on page 8 for the allowed crystal frequency range. Figure 7. Internal Timing Reference Clock Divider
50 MHz (XTI)
75 MHz (REF_CLK)
Figure 8. External Component Requirements for Crystal Circuit
14 DS761PP1
5.1.3 External Reference Clock (REF_CLK)
5.2 Frequency Reference Clock Input, CLK_IN
5.2.1 CLK_IN Frequency Detector
internal SysClk and the CLK_IN input signal. device to determine the Auto R-Mod value. Table 1. PLL Input Clock Range Indicator ticularly useful when used in conjunction with the Auto R-Mod feature (see section 5.3.4 on page 18).
5.2.2 CLK_IN Skipping Mode
11 Reserved
determined by the ClkOutUnl bit during this time. throughout the missing CLK_IN period including the time while the PLL re-acquires lock. Figure 9. CLK_IN removed for > 223 SysClk cycles
223 SysClk cycles 223 SysClk cycles
Figure 10. CLK_IN removed for < 223 SysClk cycles but > tCS Figure 11. CLK_IN removed for < tCS
16 DS761PP1
5.2.3 Adjusting the Minimum Loop Bandwidth for CLK_IN
the lowest PLL bandwidth setting. See Figure 12. those synchronous to the PLL_OUT domain. the minimum value selected by the ClkIn_BW[2:0] bits. Figure 12. Low bandwidth and new clock domain Figure 13. High bandwidth with CLK_IN domain re-use
5.3 Output to Input Freque ncy Ratio Configuration
5.3.1 User Defined Ratio (R UD), Frequency Synthesizer Mode
The User Defined Ratio, RUD, is a 32-bit un-signed fixed-point number which determines the basis for the desired input to output clock ratio. Up to four different ratios, Ratio0-3, can be stored in the CS2000 register space. The ratio pointed to by the RSel[1:0] bits is the currently selected ratio for the static ratio based Frequency Synthesizer Mode. The 32-bit RUD is represented in a high-resolution 12.20 format where the
12 MSBs represent the integer binary portion while the remaining 20 LSBs represent the fractional binary
portion. The maximum multiplication factor is approximately 4096 with a resolution of 0.954 PPM in this configuration. See “Calculating the User Defined Ratio” on page 33 for more information. The status of internal dividers, such as the internal timing reference clock divider, are automatically taken into account. Therefore R UD is simply the desired ratio of the output to input clock frequencies.
5.3.2 User Defined Ratio (R UD), Hybrid PLL Mode
The same four ratio locations, Ratio0-3, are used to store the User Defi ned Ratios for Hybrid PLL Mode. The User Defined Ratio pointed to by the LockClk[1:0] bits is the currently selected ratio for the dynamic ratio based Hybrid PLL Mode. In addition to the High-Resolution format, a High-Multiplication format is also available. In the High-Multi- plication Format Mode, the 32-bit RUD is represented in a 20.12 format where the 20 MSBs represent the integer binary portion while the remaining 12 LSBs repr esent the fractional binary portion. In this config- uration, the maximum multiplication factor is approximately 1,048,575 with a resolution of 244 PPM. The ratio format default is 20.12. The 20.12 ratio format is only available when both the LFRatioCfg bit is cleared (20.12) and the FracNSrc bit is set (dynamic ratio). In Auto Fractional-N Source Mode (see section 5.3.6.2 on page 20 ) when CLK_IN is not present the LFRatioCfg bit is ignored and the ratio format is 12.20. It is recommended that the 12.20 High-Resolution fo rmat be utilized whenever the desired ratio is less than 4096 since the output frequency accuracy of the PLL is directly proportional to the accuracy of the timing reference clock and the resolution of the RUD. Referenced Control Register Location Referenced Control Register Location
18 DS761PP1
5.3.3 Manual Ratio Modifier (R-Mod)
Table 2. Ratio Modifier
5.3.4 Automatic Ratio Modifier (Aut o R-Mod) - Hybrid PLL Mode Only
ifier is enabled by the AutoRMod bit. Table 3. Automatic Ratio Modifier by the RModSel[2:0] bits and is used to calculate the Effective Ratio (see Section 5.3.5 on page 19).
set to 10), the Frequency Range Indicator would then reflect the frequency range of the audio sample rate. An RUD of 512 would then generate the audio oversampling clocks as shown in Table 4.
5.3.5 Effective Ratio (R EFF)
to be altered to account for internal dividers. tional-N Source Selection for the Frequency Synthesizer” on page 20). Table 4. Example Audio Oversampling Clock Generation from CLK_IN
20 DS761PP1
5.3.6 Fractional-N Source Selection
To select between the static ratio based Frequency Synthesizer Mode and the dynamic ratio based Hybrid PLL Mode, the source for the fractional-N value for the Frequency Synthesizer must be changed. The Fractional-N value can either be sourced directly from the Effective Ratio (static ratio) or from the output of the Digital PLL (dynamic ratio) (see Figure 14 on page 21 ). The setting of this function can be made manual or automatically depending on the presence of CLK_IN.
5.3.6.1 Manual Fractional- N Source Selection for the Frequency Synthesizer
Manual selection of the fractional-N source for th e frequency synthesizer is made by setting the FracNSrc bit to select the desired ratio source. The LockClk[1:0] bits (even if unused) must be set to the same value as the RSel[1:0] bits in order to maintain manual selectability of this function (see Section 5.3.6.2 on page 20).
5.3.6.2 Automatic Fractional-N Source Se lection for the Frequency Synthesizer
Automatic source selection allows for the selection of the frequency synthesizer’s fractional-N value to be made dependent on the presence of the CLK_IN signal. When CLK_IN is present the device will use the dynamic ratio generated from the Digital PLL and CLK_IN for Hybrid PLL Mode. When CLK_IN is not present, the device will use RefClk and the static ratio fo r Frequency Synthesizer Mode. Before switching to SysClk and re-acquiring lock the CS2000 will wait for 223 SysClk cycles after losing CLK_IN (see “CLK_IN Skipping Mode” on page 14). The User Defined Ratio pointed to by RSel[1:0] should contain the desired CLK_OUT to RefClk ra- tio to be used when CLK_IN is not presen t. The User Defined Ratio pointed to by LockClk[1:0] should contain the desired CLK_OUT to CLK_IN ratio to be used when CL K_IN is present. Auto- matic source selection is enabled when the LockClk[1:0] bits are set to point to a different User De- fined Ratio from the one pointed to by the RSel[1:0] bits. When automatic source selection is enabled, the FracNSrc bit (used for manual clock selection) will be ignored. To disable the automatic source selection feature, set the LockClk[1:0] bits and the RSel[1:0] bits to the same value. The FracNSrc bit must then be used to select the desired clock used for the PLL’s frequency reference. Referenced Control Register Location Referenced Control Register Location
5.3.7 Ratio Configuration Summary
Figure 14. Ratio Feature Summary
22 DS761PP1
5.4 PLL Clock Output
The PLL clock output pin (CLK_OUT) provides a buffered version of the output of the frequency synthesizer. The driver can be set to high-impedance with the ClkOutDis bit. CLK_OUT may then be unreliable during an unlock condition. Figure 15. PLL Clock Output Options
5.5 Auxiliary Output
then used to control the output driver ty pe and polarity of the LOCK signal (see section 8.7.2 on page 31). CLK_OUT pin. The driver for the pin can be set to high-impedance using the AuxOutDis bit. Figure 16. Auxiliary Output Selection
5.6 Clock Output Stability Considerations
5.6.1 Output Switching
CS2000 is designed such that re-configuration of the clock routing functions do not result in a partial clock period on any of the active outputs (CLK_OUT and/or AUX_OUT). In particular, enabling or disabling an output, changing the auxiliary output source between REF_CLK and CLK_OUT, changing between Fre- quency Synthesizer and Hybrid PLL Mode, and the automatic disabling of the output(s) during unlock will not cause a runt or partial clock period. The following exceptions/limitations exist:
- Enabling/disabling AUX_OUT when AuxOutSrc = 11 (unlock indicator).
- Switching AuxOutSrc[1:0] to or from 01 (PLL cl ock input) and to or from 11 (unlock indicator) (Transitions between AuxOutSrc[1:0] = [00,10] will not produce a glitch).
- Changing the ClkOutUnl bit while the PLL is in operation. When any of these exceptions occur, a partial clock period on the output may result.
5.6.2 PLL Unlock Conditions
Certain changes to the clock inputs and registers can cause the PLL to lose lock which will affect the pres- ence the clock signal on CLK_OUT. The following outlines which conditions cause the PLL to go un- locked:
- Changes made to the registers which affect the Fr action-N value that is used by the Frequency Syn- thesizer. This includes all the bits shown in Figure 14 on page 21.
- Any discontinuities on the Ti ming Reference Clock, REF_CLK.
- Discontinuities on the Frequency Reference Clock, CLK_IN, except when the Clock Skipping feature is enabled and the requirements of Clock Skipping are satisfied (see “CLK_IN Skipping Mode” on page 14).
- Gradual changes in CLK_IN frequency great er than ±30% from the starting frequency.
- Step changes in CLK_IN frequency.
24 DS761PP1
the AD0/CS pin through a resistor to VD or GND, thereby permanently selecting the desired AD0 bit address state. In both modes the EnDevCfg1 and EnDevCfg2 bits must be set to 1 for normal operation. WARNING: All “Reserved” registers must maintain their default state to ensure proper functional operation.
6.1 SPI Control
device only supports write operations. the data which will be placed into the register designated by the MAP. ment after each byte is read or written, allowing block writes of successive registers.
6.2 I²C Control
In I²C Mode, SDA is a bidirectional dat a line. Data is clocked into and ou t of the device by the clock, SCL. Figure 17. Control Port Timing in SPI Mode
26 DS761PP1
6.3 Memory Address Pointer
The Memory Address Pointer (MAP) byte comes after the address byte and selects the register to be read or written. Refer to the pseudocode above for implementation details.
6.3.1 Map Auto Increment
The device has MAP auto increment capability enabled by the INCR bit (the MSB) of the MAP. If INCR is set to 0, MAP will stay constant for successive I²C writes or reads and SPI writes. If INCR is set to 1, MAP will auto increment after each byte is read or written, allowing block reads or writes of successive regis- ters. 7. REGISTER QU ICK REFERENCE This table shows the register and bit names with their associated default values. EnDevCfg1 and EnDevCfg2 bits must be set to 1 for normal operation. WARNING: All “Reserved” registers must maintain their default state to ensure proper functional operation. Adr Name 7 6 5 4 3 2 1 0 01h Device ID Device4 Device3 Device2 Devic e1 Device0 Revision2 Revision1 Revision0 p2 7 00000 x xx 02h Device Ctrl Unlock FsDet1 FsDet0 Reserved Reserved Reserved AuxOutDis ClkOutDis p2 7 xxx00000 03h Device Cfg 1 RModSel2 RModSel1 RModSel0 RSe l1 RSel0 AuxOutSrc1 AuxOutSrc0 EnDevCfg1 p2 8 00000 0 00 04h Device Cfg 2 Reserved Reserved Reserved Re served AutoRMod LockClk1 LockClk0 FracNSrc p2 9 00000 0 00 05h Global Cfg Reserved Reserved Reserved Res erved Freeze Reserved Reserved EnDevCfg2 p3 0 00000 0 00 06h 09h 32-Bit Ratio 0 0Ah 0Dh 32-Bit Ratio 1 0Eh 11h 32-Bit Ratio 2 12h 15h 32-Bit Ratio 3 16h Funct Cfg 1 ClkSkipEn AuxLockCfg Reserved Ref ClkDiv1 RefClkDiv0 Reserved Reserved Reserved p3 1 00000 0 00 17h Funct Cfg 2 Reserved Reserved Reserved ClkOutUnl LFRatioCfg Reserved Reserved Reserved p3 2 00000 0 00 1Eh Funct Cfg 3 Reserved ClkIn_BW2 ClkIn_BW1 Clk In_BW0 Reserved Reserved Reserved Reserved p3 2 00000 0 00
- REGISTER DESCRIPTIONS In I²C Mode all registers are read/write unless otherwise stated. In SPI mode all registers are write only. All “Re- served” registers must maintain their default state to ensure proper functional operation. The default state of each bit after a power-up sequence or reset is indicated by the shaded row in the bit decode table and in the “Register Quick Reference” on page 26. Control port mode is entered when the device recognizes a valid chip address input on its I²C/SPI serial control pins and the EnDevCfg1 and EnDevCfg2 bits are set to 1. 8.1 Device I.D. and R evision (Address 01h)
8.1.1 Device Identification (Device[4:0]) - Read Only
I.D. code for the CS2000.
8.1.2 Device Revision (Revision[2:0]) - Read Only
CS2000 revision level.
8.2 Device Control (Address 02h)
8.2.1 Unlock Indicator (Unlock) - Read Only
Indicates the lock state of the PLL.
8.2.2 PLL Input Sample Rate Indi cator (FsDet[1:0]) - Read Only
Indicates the range of the frequency of CLK_IN relative to the frequency of SysClk. For audio applications, this can be used to distinguish single-, double-, and quad-speed modes. 76543210 Device4 Device3 Device2 Device1 Device0 Revision2 Revision1 Revision0 Device[4:0] Device 00000 CS2000. REVID[2:0] Revision Level 100 B2. 76543210 Unlock FsDet1 FsDet0 Reserved Reserved Reserved AuxOutDis ClkOutDis Unlock PLL Lock State 0 PLL is Locked. 1 PLL is Unlocked. FsDet[1:0] fSysClk / fCLK_IN 00 > 224. 01 96 to 224. 10 < 96. 11 Reserved. Application: “CLK_IN Frequency Detector” on page 14
28 DS761PP1
8.2.3 Auxiliary Output Disable (AuxOutDis)
This bit controls the output driver for the AUX_OUT pin.
8.2.4 PLL Clock Output Disable (ClkOutDis)
This bit controls the output driver for the CLK_OUT pin.
8.3 Device Configuration 1 (Address 03h)
8.3.1 R-Mod Selection (RModSel[2:0])
Selects the R-Mod value, which is used as a factor in determining the PLL’s Fractional N.
8.3.2 Ratio Selection (RSel[1:0])
Selects one of the four stored User Defined Ratios for use in the static ratio based Frequency Synthesizer Mode. AuxOutDis Output Driver State 0 AUX_OUT output driver enabled. 1 AUX_OUT output driver set to high-impedance. Application: “Auxiliary Output” on page 22 ClkOutDis Output Driver State 0 CLK_OUT output driver enabled. 1 CLK_OUT output driver set to high-impedance. Application: “PLL Clock Output” on page 22 76543210 RModSel2 RModSel1 RModSel0 RSel1 RSe l0 AuxOutSrc1 AuxOutSrc0 EnDevCfg1 RModSel[2:0] R-Mod Selection 000 Left-shift R-value by 0 (x 1). 001 Left-shift R-value by 1 (x 2). 010 Left-shift R-value by 2 (x 4). 011 Left-shift R-value by 3 (x 8). 100 Right-shift R-value by 1 (÷ 2). 101 Right-shift R-value by 2 (÷ 4). 110 Right-shift R-value by 3 (÷ 8). 111 Right-shift R-value by 4 (÷ 16). Application: “Manual Ratio Modifier (R-Mod)” on page 18 RSel[1:0] Ratio Selection 00 Ratio 0. 01 Ratio 1. 10 Ratio 2. 11 Ratio 3. Application: “User Defined Ratio (RUD), Frequency Synthesizer Mode” on page 17
8.3.3 Auxiliary Output Sour ce Selection (AuxOutSrc[1:0])
Selects the source of the AUX_OUT signal. Note: When set to 11, AuxLckCfg sets the polarity and driver type (“AUX PLL Lock Output Configura- tion (AuxLockCfg)” on page 31).
8.3.4 Enable Device Configurat ion Registers 1 (EnDevCfg1)
This bit, in conjunction with EnDevCfg2, enables control port mode. Both bits must be set to 1 during ini- tialization. Note: EnDevCfg2 must also be set to enable control port mode (“SPI / I²C Control Port” on page 24).
8.4 Device Configuration 2 (Address 04h)
8.4.1 Auto R-Modifier Enable (AutoRMod)
Controls the automatic ratio modifier function.
8.4.2 Lock Clock Ratio (LockClk[1:0])
Selects one of the four stored User Defined Ratios for use in the dynamic ratio based Hybrid PLL Mode. AuxOutSrc[1:0] Auxiliary Output Source 00 RefClk. 01 CLK_IN. 10 CLK_OUT. 11 PLL Lock Status Indicator. Application: “Auxiliary Output” on page 22 EnDevCfg1 Register State 0 Disabled. 1 Enabled. Application: “SPI / I²C Control Port” on page 24 76543210 Reserved Reserved Reserved Reserved AutoRMod LockClk1 LockClk0 FracNSrc AutoRMod Automatic R-Mod State 0 Disabled. 1 Enabled. Application: “Automatic Ratio Modifier (Auto R-Mod) - Hybrid PLL Mode Only” on page 18 LockClk[1:0] CLK_IN Ratio Selection 00 Ratio 0. 01 Ratio 1. 10 Ratio 2. 11 Ratio 3. Application: Section 5.3.2 on page 17
30 DS761PP1
8.4.3 Fractional-N Source for Fr equency Synthesizer (FracNSrc)
Selects static or dynamic ratio mode when auto clock switching is disabled.
8.5 Global Configur ation (Address 05h)
8.5.1 Device Configuration Freeze (Freeze)
Setting this bit allows writes to the Device Control and Device Configuration registers (address 02h - 04h) but keeps them from taking effect until this bit is cleared.
8.5.2 Enable Device Configurat ion Registers 2 (EnDevCfg2)
This bit, in conjunction with EnDevCfg1, enables control port mode. Both bits must be set to 1 during ini- tialization. Note: EnDevCfg1 must also be set to enable control port mode (“SPI / I²C Control Port” on page 24).
8.6 Ratio 0 - 3 (Address 06h - 15h)
These registers contain the User Defined Ratios as shown in the “Register Quick Reference” section on page 26. Each group of 4 registers forms a single 32-bit ratio value as shown above. See “Output to Input Frequency Ratio Configuration” on page 17 and “Calculating the User Defined Ratio” on page 33 for more details. FracNSrc Fractional-N Source Selection
0 Static Ratio directly from REFF for Frequency Synthesizer Mode
1 Dynamic Ratio from Digital PLL for Hybrid PLL Mode
Application: “Fractional-N Source Selection” on page 20 76543210 Reserved Reserved Reserved Reserved Freeze Reserved Reserved EnDevCfg2 FREEZE Device Control and Configuration Registers 0 Register changes take effect immediately. 1 Modifications may be made to Device Control and Device Configuration registers (registers 02h-04h) without the changes taking effect until after the FREEZE bit is cleared. EnDevCfg2 Register State 0 Disabled. 1 Enabled. Application: “SPI / I²C Control Port” on page 24 76543210
8.7 Function Configuration 1 (Address 16h)
8.7.1 Clock Skip Enable (ClkSkipEn)
This bit enables clock skipping mode for the PLL and allows the PLL to mainta in lock even when the CLK_IN has missing pulses. Note: fCLK_IN must be < 80 kHz to use this feature.
8.7.2 AUX PLL Lock Output Configuration (AuxLockCfg)
When the AUX_OUT pin is configured as a lock indicator ( AuxOutSrc[1:0] = 11), this bit configures the AUX_OUT driver to either push-pull or open drain. It also determines the polarity of the lock signal. If AUX_OUT is configured as a clock output, the state of this bit is disregarded. Note: AUX_OUT is an unlock indicator, signalling an error condition when the PLL is unlocked. There- fore, the pin polarity is defined relative to the unlock condition.
8.7.3 Reference Clock Input Divider (RefClkDiv[1:0])
Selects the input divider for the timing reference clock. 76543210 ClkSkipEn AuxLockCfg Reserved RefClkDiv 1 RefClkDiv0 Reserved Reserved Reserved ClkSkipEn PLL Clock Skipping Mode 0 Disabled. 1 Enabled. Application: “CLK_IN Skipping Mode” on page 14 AuxLockCfg AUX_OUT Driver Configuration 0 Push-Pull, Active High (output ‘high’ for unlocked condition, ‘low’ for locked condition). 1 Open Drain, Active Low (output ‘low’ for unl ocked condition, high-Z for locked condition). Application: “Auxiliary Output” on page 22 RefClkDiv[1:0] Reference Clock Input Divider REF_CLK Frequency Range 00 ÷4 . 32 MHz to 75 MHz (50 MHz with XTI) 01 ÷ 2. 16 MHz to 37.5 MHz 10 ÷ 1. 8 MHz to 18.75 MHz 11 Reserved. Application: “Internal Timing Reference Clock Divider” on page 13
32 DS761PP1
8.8 Function Configuration 2 (Address 17h)
8.8.1 Enable PLL Clock Out put on Unlock (ClkOutUnl)
Defines the state of the PLL output during the PLL unlock condition.
8.8.2 Low-Frequency Ratio Configuration (LFRatioCfg)
Determines how to interpret the currently indexed 32-bit User Defined Ratio when the dynamic ratio based Hybrid PLL Mode is selected (either manually or automatically, see section 5.3.6 on page 20). Note: When the static ratio based Fr equency Synthesizer Mode is sele cted (either manually or auto- matically), the currently indexed User Defined Ratio will always be interpreted as a 12.20 fixed point value, regardless of the state of this bit.
8.9 Function Configuration 3 (Address 1Eh)
8.9.1 Clock Input Bandwidth (ClkIn_BW[2:0])
Sets the minimum loop bandwidth when locked to CLK_IN. Note: In order to guarantee that a change in minimum bandwidth takes effect, these bits must be set prior to acquiring lock (removing and re-applying CLK_IN can provide the unlock condition necessary to initiate the setting change). In production systems these bits should be configured with the desired values prior to setting the EnDevCfg bits; this guarantees that the setting takes effect prior to acquiring lock. 76543210 Reserved Reserved Reserved ClkOutUnl LFRatioCfg Reserved Reserved Reserved ClkOutUnl Clock Output Enable Status 0 Clock outputs are driven ‘low’ when PLL is unlocked. 1 Clock outputs are always enabled (results in unpredictable output when PLL is unlocked). Application: “PLL Clock Output” on page 22 LFRatioCfg Ratio Bit Encoding Interpretation when Input Clock Source is CLK_IN 0 20.12 - High Multiplier. 1 12.20 - High Accuracy. Application: “User Defined Ratio (RUD), Hybrid PLL Mode” on page 17 76543210 Reserved ClkIn_BW2 ClkIn_BW1 ClkIn_BW0 Reserved Reserved Reserved Reserved ClkIn_BW[2:0] Minimum Loop Bandwidth 000 1 Hz 001 2 Hz 010 4 Hz 011 8 Hz 100 16 Hz 101 32 Hz 110 64 Hz 111 128 Hz Application: “Adjusting the Minimum Loop Bandwidth for CLK_IN” on page 16
- CALCULATING THE US ER DEFINED RATIO
systems without the aid of the evaluation kit. generate a binary or hex value which can be written to the Ratio0-3 registers. culator and write to the register. A few examples have been provided in Table 5. Table 5. Example 12.20 R-Values write to the register. A few examples have been provided in Table 6. Table 6. Example 20.12 R-Values
12.288 MHz/60 Hz=204,800 838860800 32 00 00 00
34 DS761PP1
10.PACKAGE DIMENSIONS Notes: 1. Reference document: JEDEC MO-187 2. D does not include mold flash or prot rusions which is 0.15 mm max. per side. 3. E1 does not include inter-lead flash or protrusions which is 0.15 mm max per side. 4. Dimension b does not include a total allo wable dambar protrusion of 0.08 mm max. 5. Exceptions to JEDEC dimension. THERMAL CHARACTERISTICS INCHES MILLIMETERS NOTE DIM MIN NOM MAX MIN NOM MAX A1 0 -- 0.0059 0 -- 0.15 A2 0.0295 -- 0.0374 0.75 -- 0.95 b 0.0059 -- 0.0118 0.15 -- 0.30 4, 5 Parameter Symbol Min Typ Max Units Junction to Ambient Thermal Impedance JEDEC 2-Layer JEDEC 4-Layer θJA θJA 170 100 °C/W °C/W 10L MSOP (3 mm BODY) PACKAGE DRAWING (Note 1) E N 1 23 e b A1 A2 A D SEATING PLANE E11 L SIDE VIEW END VIEW TOP VIEW c
11.ORDERING INFORMATION 12.REFERENCES 1. Audio Engineering Society AES-12id-2006: “AES Information Document for digital audio measurements - Jitter performance specifications,” May 2007. 2. Philips Semiconductor, “ The I²C-Bus Specification: Version 2,” Dec. 1998. http://www.semiconductors.philips.com 13.REVISION HISTORY Product Description Package Pb-Free Grade Temp Range Container Order# CS2000-CP Clocking Device 10L-MSOP Yes Commercial -10° to +70°C Rail CS2000-CP-CZZ CS2000-CP Clocking Device 10L-MSOP Yes -10° to +70°C Tape and Reel CS2000-CP-CZZR CDK2000 Evaluation Platform - Yes - - - CDK-2000-CLK Release Changes A1 Initial Release A2 Updated AC Electrical Characteristics A3 Updated text for readability Updated application section for “CLK_IN Skipping Mode” on page 14 Added application section for “Adjusting the Minimum Loop Bandwidth for CLK_IN” on page 16 Added register description for “Clock Input Bandwidth (ClkIn_BW[2:0])” on page 32 PP1 Updated “AC Electrical Characteristics” on page 8 Contacting Cirrus Logic Support For all product questions and inquiries, contact a Cirrus Logic Sales Representative. To find one nearest you, go to www.cirrus.com IMPORTANT NOTICE “Preliminary” product information describes products that are in production, but for which full characterization data is not yet available. Cirrus Logic, Inc. and its subsidiaries (“Cirrus”) believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided “AS IS” without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives con- sent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROP- ERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRIT- ICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND CIR- RUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOM- ER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING AT- TORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. I²C is a registered trademark of Philips Semiconductor. SPI is a trademark of Motorola, Inc.