6462091 CLARKE | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 32
Technical content
OPERATION & MAINTENANCE INSTRUCTIONS GC04/24 Rev 2 ORIGINAL INSTRUCTIONS BENCHTOP SHAPER/ROUTER MODEL NO: CBTSR2 PART NO: 6462091
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for selecting this Clarke product. The machine is ideal for shaping wood and plastic and also for cutting out knots, cutting grooves, removing recesses, copying curves and logos, etc. The machine must not be used on metal, stone, etc. Please note that setting up and adjustment of this product ideally requires some experience of working with this type of equipment. Save these instructions including all safety warnings and instructions for future reference. SPECIFICATIONS Feature Specification Operating Voltage and Frequency 230V ~ @ 50 Hz Rated Input Wattage: 1500W Table Size (with extension) L x W (mm) 1030 x 360 mm Speeds 11500 rpm to 24000 rpm Ingress protection rating IP20 Spindle height adjustment 0 - 40 mm Shank size 6/8/12mm and ¼” / ½” Max Dimension of workpiece (L x W x H) 650 x 160 x 65 mm Table Insert Sizes 32/47/55/75 mm Dust Extract Adaptor Diameter Outer Dia: 100 mm Inner Dia: 93 mm Sound Pressure 89 dB (A) Sound Power Guaranteed LWa 102 dB Product Weight (Unpacked): 20.9 kg
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com GENERAL POWER TOOL SAFETY WARNINGS 1. Keep the work area tidy.
- Clutter in the work area can lead to accidents. 2. Take environmental influences into account. DO NOT expose power tools to rain. DO NOT use power tools in a damp or wet environment. Make sure that the work area is well lit. DO NOT use power tools where there is a risk of fire or explosion. 3. Protect yourself from electric shock. 4. Keep other persons away. DO NOT let persons, especially childre n, not involved in the work touch the machine and keep them away from the work area. 5. Securely store unused power tools. Unused power tools should be stored in a dry, elevated or enclosed location out of the reach of children. 6. DO NOT overload your power tool. They work better and more safely in the specified output range. 7. Use the correct power tool for the task. DO NOT use low-output power tools for heavy work. DO NOT use the power tool for purposes for which it is not intended. 8. Wear suitable clothing. DO NOT wear loose clothing or jewelry, which can become entangled in moving parts. When working outdoors, anti-slip footwear is recommended. Tie back and restrain long hair. 9. Use protective equipment. Wear protective eye wear. Wear a dusk mask when carry ing out dust-creating work. WARNING: READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. FAILURE TO FOLLOW THE WARNINGS AND INSTRUCTIONS MAY RESULT IN ELECTRIC SHOCK, FIRE AND/OR SERIOUS INJURY.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 10. Connect the dust extract if you will be processing wood, materials similar to wood or plastics. If connections for dust extraction and a collecting device are present, make sure that they are connected and used properly. When processing wood materials and plastics, operation in enclosed spaces is only permitted with the use of a suitable extraction system. 11. DO NOT use the power cable for purposes for which it is not intended. DO NOT use the power cable to pull t he plug out of the socket. Protect the cable from heat, oil and sharp edges. 12. Secure the workpiece. Use clamping devices to hold the wo rkpiece in place as it is held more securely than with your hand. An additional support is necessary for long workpieces (table, trestle, etc.) in order to prevent the machine from tipping over (if not bolted down). Always press the workpiece firmly against the working plate and fence in order to prevent bouncing and twisting of the workpiece. 13. Avoid abnormal posture. Make sure that you have secure footing and always maintain your balance. Avoid awkward hand positions in which a sudden slip could cause one or both hands to come into contact with the cutter bit. 14. Take care of your tools. Keep cutting tools sharp and clean in order to be able to work better and more safely. Check the power cable of the po wer tool regularly and have it replaced by a recognised specialist if damaged. Check extension cables regularly and replace them if damaged. NEVER remove loose splinters, chips or jammed wood pieces from the cutter bit until it has stopped. If the cutter bit is blocked due to abnormal feed force during cutting, turn the machine off and remove the work piece. Ensure that the cutter bit runs freely. Turn the machine back on and start a new cutting operation with less feed force. 15. Before switching on, make sure that any adjusting tools are removed. 16. Avoid inadvertent starting.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com Make sure that the machine is switch ed off when inserting the plug into a power outlet. 17. Stay alert. Pay attention to what you are doin g. DO NOT use the power tool when you are distracted, tired, or under the influence of drugs or alcohol. 18. Check the power tool for potential damage. Protective devices and other parts must be carefully inspected to ensure that they are fault free and function as intended prior to continued use of the power tool. Check whether the moving parts function faultlessly and do not jam or if parts are damaged. All parts must be correctly mounted and all conditions must be fulfilled to ensure fault free operation of themachine. Damaged protective devices and part s must be properly repaired or replaced. DO NOT use faulty or damaged connecting cables. DO NOT use apower tool if the swit ch cannot be switched on and off. 19. The use of other accessories than recommended items can have a risk of injury. 20. Have your power tool repaired by a qualified electrician. This power tool conforms to the app licable safety regulations. Repairs may only be performed by an electrician using original spare parts or accidents could occur. 21. The operator must always stand in front of the machine while working. ADDITIONAL SAFETY INSTRUCTIONS FOR ROUTERS 1. Check that cutting bits are in perfect condition before use. 2. Use table insert rings appropriate for the size of the cutting bits. 3. ALWAYS wear suitable personal protective equipment including: Hearing protection to avoid the ri sk of becoming hearing impaired. Respiratory protection to avoid the risk of inhaling harmful dust. Safety goggles to avoid eye injuries due to flying particles. 4. Beware of injury when handling bi ts and materials with sharp edges. 5. When working with wood, beware of conditions that cause the release of dust, e.g. the type of material to be processed and the correct setting of the hood/guide plates/guides. 6. Support long workpieces suffici ently to hold their position.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 7. Take care of possible rebound due to any guide for a small workpiece being unsuitable. 8. Use additional equipment when processing narrow workpieces. 9. Tools that have not been maintained can trigger uncontrollable situations. Only use sharp, well maintained cutting bits. 10. Before changing cutting bits or making adjustments, switch off the machine. 11. Select a rotational speed that is suitable for the cutting bit and work material used. RESIDUAL RISKS The machine is built according to current and recognized safety regulations. Nevertheless residual risks can occur during work. Danger of injury to fingers and hands by the tool due to inappropriate guidance of the work piece. Injuries caused by a work piece flying off due to lack of restraint or guidance. Health hazards due to wood dust or wood chips. Wear personal protection equipment such as eye protection. Use a ventilation system. Injuries by defective tools. Examin e the tool regularly for soundness. Danger of injury to fingers and hand s during tool changes. Wear suitable working gloves. Danger of injury when switching on the machine. Hazards due to current by use of incorrect electrical connecting cables. Residual risks can be minimized if th e safety instructions and operating instructions are followed in full. SAFETY SYMBOLS ON THE MACHINE OR PACKAGING Read instruction manual before use Wear ear defenders Wear safety glasses Wear a breathing mask. Wear protective gloves
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ELECTRICAL CONNECTIONS This machine is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing, make sure that a plug of identical specification is used. If the colours of the wires in the power cable do not agree with the markings on the plug: Connect the blue wire to the terminal which is marked N. Connect the brown wire to the terminal which is marked L. Connect the yellow and green wire to the terminal which is marked E or We strongly recommend that this machine is connected to the mains supply through a Residual Current Device (RCD) If you are not sure, consult a qualified electrician. DO NOT try to do any repairs. CABLE EXTENSIONS Always use an approved cable extension suitable for the power rating of this machine. The conductor size should also be at least the same size as that on the machine, or larger. WARNING! READ THESE ELECTRICAL SAFETY INSTRUCTIONS FULLY BEFORE CONNECTING THE MACHINE TO THE MAINS SUPPLY. WARNING! THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE: BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH Plug must be BS1363/A approved. Always fit Ensure that the outer sheath of Neutral (Blue) Live (Brown) Earth (Green and a 13 Amp the cable is firmly held by the clamp fuse. Yellow)
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INVENTORY The following items are supplied for fitting/assembly. 1. Fence (52) 2. Sliding Bracket (64) 3. Fence Plate (66) 4. Downwards Pressure Bar (63) 5. Mounting Bracket for the above (56) 6. 2 x Pressure Pads (68) 7. Square Mounting Plates (61) 8. Square Supports (60) 9. Elevating Handle (31) 10. Table Extensions (41 & 71) 11. Kickback Safety Fence (103) 12. Mounting Bracket for the above (104) 13. Dust Extractor Adaptor (53) - (not shown) 14. Transparent Tool Guard (50) - (not shown) 15. 6mm Collet (78) 16. 8mm Collet (77) 17. 12 mm Collet 18. Table Insert Rings (49) 19. Spanners (73) 20. 3mm Hex Key (74) 21. 4mm Hex Key (75) 22. Mitre Fence (99) 23. Push Blocks (72) 24. Fixings Packs 25. Table extension alignment bracket Numbers in brackets refer to pages 26-29.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com COMPONENT INVENTORY
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ASSEMBLY MOUNTING THE MACHINE It is recommended to fix the machine to a workbench using the four holes provided. Holes must be drilled in the workb ench which align with those on the machine base. Each corner must be secured to the workbench using nuts and bolts long enough to go through the workbench (not supplied). The workbench must be large enough to prevent tilting of the machine when working. ASSEMBLING THE FENCE Before starting work the fence must be assembled and fitted to the work table. FITTING THE SLIDING BRACKET TO THE FENCE 1. Insert the carriage bolt into the fence from below as shown. Parts needed for this step 1 x Fence 1 x Sliding bracket 1 x Carriage bolt M6 x 25 1 x Plastic cap nut M6 1 x Washer 6mm
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 2. Drop the sliding bracket over the bolt so that it sits in the grooves on the fence. 3. Secure in place using the washer and plastic cap nut. FITTING THE FENCE PLATES 1. Insert the 4 carriage bolts into the attachment holes and screw them on finger tight with a washer and a plastic cap nut. 2. Slide the fence plates over the carriage bolt heads. Make sure that the fence plates are at the same height. 3. Tighten the plastic cap nut to lock the fence plates in position. Parts needed for this step 4 x Carriage bolt M6 x 20 4 x Plastic cap nut M6 4 x Washers 6mm 2 x Fence plates
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com FITTING THE DOWNWARD PRESSURE BAR 1. Fit the mounting bracket to the central part of the main fence as shown. 2. Secure in place using 2 x M6 x 40 bolts (from below), 2 washers and 2 x M6 nuts supplied. 3. Position the pressure bar and lock in position using the 2 carriage bolts, 2 washers and 2 wing nuts provided. Parts needed for this step 1 x Mounting Bracket 2 x Bolt M6 x 40 2 x Nut M6 4 x Washers 6mm 1 x Pressure Bar 2 x Carriage Bolts M6 x 35 2 x Wingnuts M6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com FITTING THE PRESSURE PADS 1. Insert the 2 square supports in the 2 square sockets on the main part of the fence. 2. Secure them with the 2 Allen screws from below. NOTE: You will need to slide the sliding bracket forward to gain access to one of the holes. Parts needed for this step 2 x Pressure pads 2 x Square mounting plate 2 x Square supports 2 x Clamp 2 x Allen screws M6 x 16 2 x Plastic cap screws M6 x 20 4 x Carriage bolts M6 x 35 4 x Plastic cap nuts M6 4 x Washers 6mm
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 3. Slide the square mounting plate into the clamp as shown. 4. Slide the clamp over the square support as shown. 5. Secure in place by tightening the knob on the clamp. Repeat for the other assembly. 6. Fit the pressure pads to the square mounting plates using 4 carriage bolts, 4 washers and 4 plastic cap nuts.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com FITTING THE FENCE ONTO THE WORKING TABLE 1. Fix the 2 plastic cap screws into the grooves in the fence using the washers and carriage bolts as shown. The longer carriage bolt goes on the right, when viewing the fence from the rear. 2. Put the tops of the carriage bolts through the opening in the table. 3. Position the fence as required and tighten the plastic cap nuts. FITTING THE HANDLE 1. Slide the handle over the shaft making sure it engages with the pin. 2. Secure in place using the nut. Parts needed for this step 1 x Carriage bolt M6 x 20 1 x Carriage bolt M6 x 40 2 x Plastic cap nuts M6 2 x Washers 6mm Parts needed for this step 1 x Handle 1 x Nut (already fitted) M8
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com FITTING THE TABLE EXTENSION 1. Remove the fence and use the table alignment tool to accurately position the table extension for assembly. Tighten the wingnuts to secure in position. 2. Flip the unit upside down onto a smooth flat surface. 3. Attach the extension table to both sides with 4 allen screws M5 x 20, 4 washers and 4 hexagonal nyloc nuts M5. 4. Also secure using 3 allen screws (M5 x 12), 3 washers and 3 spring washers each. 5. Align the table and tighten all screws. 6. Repeat for the other table extension. 7. Flip the unit the right way up again (with assistance if required). Remove the alignment bracket and replace the fence. Parts needed for this step 2 x Table extensions 1 x Table alignment tool 8 x Allen screws M5 x 20 6 x Allen screws M5 x 12 14 x Washers 5mm 8 x Hexagonal nyloc nuts M5 6 x Spring washers 5mm
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com FITTING THE KICKBACK SAFETY FENCE 1. Align the mounting bracket with the two holes on the front of the table. 2. Insert the two cross head screws with washers into the holes and tighten. 3. Install the kickba ck safety fence You can adjust the fence to the thickness of the work piece. 4. After setting, fix it in place with the help of the two carriage bolts, 2 washers and 2 wing nuts. Parts needed for this step 1 x Kickback safety fence 1 x Mounting bracket 2 x Cross head screws with washers M5 x 10 2 x Carriage bolts M6 x 25 2 x Washers 6mm 2 x Wing nuts M6
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com CONNECTING TO A DUST EXTRACTOR Slide the suction hose of the dust extractor unit onto the dust extraction port at the rear of the moulding fence. For hoses with a dia of 100 mm, using the adapter supplied. FITTING THE TRANSPARENT TOOL GUARD 1. Remove downward pressure ba r and bracket shown on page 12. 2. Place transparent tool guard in position as shown. 3. Insert pin to secure. Check to see the guard functions correctly before use.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com BEFORE USE INSTALLING AND CHANGING THE COLLETS AND CUTTING BITS 1. Remove the insert rings from the table. 2. Loosen the securing screw and use the handle to raise the spindle to its highest position. 3. Press and hold the Spindle Lock button. WARNING: BEFORE CARRYING OUT ANY ADJUSTMENT OR MAINTENANCE, MAKE SURE THAT THE MACHINE IS DISCONNECTED FROM THE MAINS SUPPLY.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com 4. Loosen the collet nut using the spanners provided and remove the cutting bit and collet nut if required. 5. Insert the required collet/collet nut and tighten it slightly. 6. Insert the bit into the collet. At least 3/4 of the cutting bit shank must be gripped in the collet before tightening. 7. Press and hold the spindle lock butt on and tighten the collet nut securely. Before every use of the machine make sure that the cutting bit is secure. 8. Place the insert rings back in to their original position. The insert rings must be used in order to keep the spacing between table and cutter to a minimum. Only fit enough insert rings so as to allow the bit to come through the surface of the table without touching the rings. Before switching on check the insert rings are seated correctly. 9. Reconnect the machine to the power supply.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ADJUSTMENTS SPEED CONTROL The speed control has 6 speeds. Determine the optimal setting by testing on a scrap piece of wood. NOTE: The use of the correct setting will increase the life-span of the cutter. It, also affects the quality of the cut. RAISING/LOWERING THE CUTTER To raise or lower the spindle height. 1. Loosen the securing screw. 2. Use the handle to raise or lower the spindle to the required height. 3. Tighten the securing screw. ADJUSTING THE FENCE 1. Loosen the plastic cap screws shown on the back of the fence. 2. Move the fence to the desired position. 3. Re-tighten the plastic cap screws to keep the fence in this position.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OUTFEED FENCE OFFSET Once the workpiece passes the cutting bit it may be thinner then when it started. If so you should adjust the left fence to compensate for the missing material. 1. Loosen the plastic cap screws. 2. Move the left fence towards you slightly and tighten the plastic cap screws. ADJUST THE CROSS-CUTTING JIG 1. Loosen the locking knob. 2. Set the jig to the desired angle. 3. Tighten the locking knob. Always make a sample cut in a piece of waste material in order to guarantee the angles are correct. SWITCHING ON AND OFF Press the green ON (I) button to start the machine. Press the red OFF (O) button to stop the machine.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com USING THE MACHINE 1. Insert an appropriate cutting bit. 2. Adjust the machine spee d and adjust the fence so that the material is supported along its entire length. 3. Switch the machine on by pressing the green ON (I) button. 4. Make sure the workpiece is firmly pressed against the fence. 5. Push the work piece softly from right to left against the turning direction of the cutting bit. Keep your speed constant. DO NOT push too fast as it would slow down the motor. Feeding the work piece too fast will resu lt in poor cutting quality. There is also the risk of damaging the cutting bit or the machine motor. Feeding the work piece too slowly w ill result in burnt spots on the work piece. The correct intake speed depends on the cutting bit size, the material type of the workpiece and the cutting depth. It is recommended to practice first with a piece of scrap wood in order to determine the correct speed. 6. With very hard wood and importan t cuts it may be better to work progressively, taking several shallow cuts until the desired depth is achieved. 7. Switch the machine off by pressing the red OFF (O) button. OVERLOAD SWITCH The machine is fitted with an overload switch to protect the motor. In the event of an overload situation, the machine will cut out automatically. After a short time press the overload reset button to reset the machine.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com MAINTENANCE AND SERVICING CLEANING Keep all safety devices, air vents an d the motor housing free of dirt and dust. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure (always wear PPE when using compressed air). We recommend that you clean the machine as soon as you have finished using it. DO NOT use cleaning agents or solvents as these could attack the plastic parts of the machine. Make sure that no water can enter the machine. The ingress of water into a power tool increases the risk of an electric shock. CUTTING BITS Any resin must be cleaned off the cutti ng bits at regular intervals with an appropriate resin remover. STORAGE Store the machine and accessories ou t of children’s reach in a dark, dry place at above freezing temperature. The ideal storage temperature is between 5 and 30°C. Ideally, store the machine in its original packaging. Cover the machine in order to pr otect it from dust and moisture. Store the operating manual with the machine. WARNING: BEFORE CARRYING OUT MAINTENANCE, MAKE SURE THAT THE MACHINE IS DISCONNECTED FROM THE MAINS SUPPLY.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com COMPONENT PARTS
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com COMPONENT PARTS No Description No Description
1 Chuck 31 Adjusting handle wheel
2 X-Pan head screw & wash er 32 Rise and fall shaft
3 Motor rise & fall guide bar 33 Motor mounting bracket
4 X-Pan head screw 34 Locking knob
5 Motor 35 Locking rod
6 Motor connecting plate 36 Hex socket cap screw
7 Slider 37 Hex socket cap screw
8 Hex socket cap screw 38 Hex socket cap screw
9 Guide profile 39 Spring washer
10 Pointer 40 Flat washer
11 Hex bolt 41 Work table side extension
12 Hex nut 42 Washer
13 Bevel gear support 43 Work table
14 Deep groove ball bearing 44 M5 Locknut
15 Hex nut 45 Hex socket cap screw
16 Hex socket cap screw & washers 46 End cap
17 Hex socket cap screw & washers 47 Straight pin
18 Support assembly 48 Hex socket cap screw
19 Bevel gear 49 Insert ring assembly
20 Vertical adjustment screw 50 Plastic tool cover
21 Circlip 51 Left end cap
22 Flat key 52 Main fence
23 Circlip 53 Dust extract adaptor
24 Vertical adjustment shaft gear 54 M6 Locknut
25 Vertical adjuster 55 Hex bolt M6x40
26 Roll pin 56 Mounting bracket
27 Handle spindle 57 Locking knob
28 Handle cap 58 Square mounting
29 Handle 59 Coachbolt M6x35
30 Dome nut 60 Square support post
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
61 T-bar 95 Circuit board
62 Hex socket cap screw M6x16 96 Rear panel
63 Pressure bar 97 X-Pan head screw/washer
64 Sliding cover bracket 98 Base plate
65 Coachbolt M6x20 99 Metre plate assembly
66 Fence Plate 100 X-Pan head screw/washer
67 X-Pan head screw M5x15 101 Butterfly nut
68 Pressure pad 102 Washer A6
69 Lock knob 103 Safety fence assembly
70 Hex socket cap screw M5x12 104 Mounting bracket
71 Worktable side extension 105 X-Pan head screw/washer
72 Push blocks 106 Coachbolt M6x25
73 Long wrench 107 Chuck ring
74 Allen wrench S4 108 Chuck nut
75 Allen wrench S5 109 Collet
76 Short wrench 110 Chuck ring
77 Chuck 12mm 111 Chuck nut
78 Chuck 6mm 112 Collet
79 Base assembly 113 Chuck ring
80 Transformer box 114 Chuck nut
81 Circuit board 115 Collet
82 Hex nut M4 116 Long fence assembly 1
83 X-Pan head screw 117 Long fence assembly
84 X-Pan head s/t screw 118 Pan head screw M5x12
85 Washer 119 Long fence connector
86 Power plug 120 Washer
87 Cable gland 121 Screw M4x12
88 Circlip 122 Fence
89 Power cable gland 123 Grille
90 X-Pan head screw/washer 124 Dowel
91 Cable clamp 125 S/t screw
92 Front panel 126 Mounting plate
93 Over-current protection 127 Countersunk screw
94 On/off switch 128 S/t screw
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com
129 Plate connecting bracket 138 Table top cover plate B
130 Connecting bar 139 Table top cover plate A
131 Securing knob 140 Self tapping screw
132 Mitre base with scale 141 Switch box cover
133 Screw 142 Connecting box
134 Washer 143 Switch
135 Slide arm 144 Sheath
136 Table top cover plate C 145 X-Pan head screw
137 Table top cover plate D 146 Handle bush
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com ENVIRONMENTAL PROTECTION Through purchase of this tool, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE. In effect, this means that this tool must not be discarded with general waste. Refer to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility. GUARANTEE The machine is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Your receipt is required as proof of purchase. This guarantee is invalid if the machine is found to have been abused, tampered with, or not used for the purpose for which it was intended. Faulty goods must be returned to their place of purchase, it must not be returned to us without prior permission. This guarantee does not effect your statutory rights.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - UK
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATION OF CONFORMITY - CE